Solar Thermal Collectors at High Latitudes : Design and performance of non-tracking concentrators

Solar thermal collectors at high latitudes have been studied, with emphasis on concentrating collectors. A novel design of concentrating collector, the Maximum Reflector Collector (MaReCo), especially designed for high latitudes, has been investigated optically and thermally. The MaReCo is an asymmetrical compound parabolic concentrator with a bi-facial absorber. The collector can be adapted to various installation conditions, for example stand-alone, roof- or wall mounted. MaReCo prototypes have been built and outdoor-tested. The evaluation showed that all types work as expected and that the highest annually delivered energy output, 340 kWh/m2, is found for the roof MaReCo. A study of the heat-losses from the stand-alone MaReCo lead to the conclusion that teflon transparent insulation should be placed around the absorber, which decreases the U-value by about 30%. A method was developed to theoretically study the projected radiation distribution incident on the MaReCo bi-facial absorber. The study showed that the geometry of the collectors could be improved by slight changes in the acceptance intervals. It also indicated that the MaReCo design concept could be used also at mid-European latitudes if the geometry is changed. A novel method was used to perform outdoor measurements of the distribution of concentrated light on the absorber and then to calculate the annually collected zero-loss energy, Ea,corr, together with the annual optical efficiency factor. A study using this method indicated that the absorber should be mounted along the 20º optical axis instead of along the 65º optical axis, which leads to an increase of about 20% in Ea,corr. The same absorber mounting is suggested from heat loss measurements. The Ea,corr at 20º absorber mounting angle can be increased by 5% if the absorber fin thickness is changed from 0.5 to 1 mm and by 13% if two 71.5 mm wide fins are used instead of one that is 143 mm wide. If the Ea,corr for the standard stand-alone MaReCo with 143 mm wide absorber mounted at 65º is compared to that of a collector with a 71.5 mm wide absorber mounted at 20º, the theoretical increase is 38%

MonitorX – Experience from a Norwegian-Swedish research project on industry 4.0 and digitalization applied to fault detection and maintenance of hydropower plants

publishedVersio

Measurement of radiation distribution on the absorber in an asymmetric CPC collector

A method to estimate the annual collected energy and the annual average optical efficiency factor is suggested. The radiation distribution on the absorber of an asymmetric CPC collector with a flat bi-facial absorber is measured for three different absorber mounting angles using a photo diode. The annual optical efficiency factors and a relative measure of the annual collected energy are determined for collectors with the absorber fin thickness 0.5 and 1 mm, and for a collector with a teflon convection suppression film mounted around the absorber. With the local optical efficiency factors and the annual incident solar energy distribution considered, the analysis indicates that the energy gain for a mounting angle of 20 is higher than for a collector with 65 absorber mounting angle. The annual collected energy is increased with 6-8% if the absorber fin thickness is increased from 0.5 to 1 mm. The annual average optical efficiency factor is relatively independent of the absorber mounting angle. It was found to be 0.87-0.88 for a collector with a 0.5 mm thick absorber fin and 0.92 for a collector with a 1 mm thick absorber fin or for a collector with 0.5 mm thick absorber fin with a teflon convection suppression film added. The low annual average optical efficiency factor is not caused by the uneven irradiance distribution but by the relatively high U-L-values. (C) 2003 Elsevier Ltd. All rights reserved

The impact of optical and thermal properties on the performance of flat plate solar collectors

The impact of the optical properties on the annual performance of flat plate collectors in a Swedish climate has been estimated with the MINSUN program. The collector parameters were determined with a theoretically based calculation program verified from laboratory measurements. The importance of changes in solar absorptance and thermal emittance of the absorber, the addition of a teflon film or a teflon honeycomb, antireflection treatment of the, cover glazing and combinations of these improvements were investigated. The results show that several improvements can be achieved for solar thermal absorbers. A combined increase in absorptance from 0.95 to 0.97 and a decrease in emittance from 0.10 to 0.05 increase the annual performance with 6.7% at 50 degreesC operating temperature. The increase in performance by installing a teflon film as second glazing was estimated to 5.6% at 50 degreesC. If instead a teflon honeycomb is installed, a twice as high performance increase is obtained, 12.1 %. Antireflection treatment of the cover glazing increases the annual output with 6.5% at 50 degreesC. A combination of absorber improvements together with a teflon honeycomb and an antireflection treated glazing results in a total increase of 24.6% at 50 degreesC. Including external booster reflectors increases the expected annual output at 50 degreesC to 19.9-29.4% depending on reflector material. (C) 2002 Elsevier Science Ltd. All rights reserved