Imaging Local Sources of Intermodulation in Superconducting Microwave Devices

This work presents new experimental results on low-temperature (LT) characterization of local rf properties of passive superconducting (SC) microwave devices using a novel Laser Scanning Microscope (LSM). In this technique, a modulated laser beam is focused onto and scanned over the surface of a resonant SC device to probe the spatial distribution of rf current. The highly localized photo-induced change of the kinetic inductance of the SC device produces both a shift of the resonant frequency f_0 and change of the quality factor Q. An image of these changes is recorded as the laser spot is scanned over the device. We present the first measurements of spatially resolved intermodulation response in a High Temperature Superconducting (HTS) co-planar waveguide resonator, opening up a new window into the local origins of nonlinearity in the HTS materials.Comment: 4 Pages, to be published in IEEE Trans. Appl. Supercond., June 200

Observation of breathers in Josephson ladders

We report on the observation of spatially-localized excitations in a ladder of small Josephson junctions. The excitations are whirling states which persist under a spatially-homogeneous force due to the bias current. These states of the ladder are visualized using a low temperature scanning laser microscopy. We also compute breather solutions with high accuracy in corresponding model equations. The stability analysis of these solutions is used to interpret the measured patterns in the I-V characteristics

Roles of intrinsic anisotropy and pi-band pairbreaking effects on critical currents in tilted c-axis MgB2 films probed by magneto-optical and transport measurements

Investigations of MgB2 and Fe-based superconductors in recent years have revealed many unusual effects of multiband superconductivity but manifestations of anisotropic multiband effects in the critical current density Jc have not been addressed experimentally, mostly because of the difficulties to measure Jc along the c-axis. To investigate the effect of very different intrinsic anisotropies of sigma and pi electron bands in MgB2 on current transport, we grew epitaxial films with tilted c-axis (THETA ~ 19.5{\deg}), which enabled us to measure the components of Jc both along the ab-plane and the c-axis using magneto-optical and transport techniques. These measurements were combined with scanning and transmission electron microscopy, which revealed terraced steps on the surface of the c-axis tilted films. The measured field and temperature dependencies of the anisotropic Jc(H) show that Jc,L parallel to the terraced steps is higher than Jc,T perpendicular to the terraced steps, and Jc of thinner films (50 nm) obtained from transport experiments at 0.1 T reaches ~10% of the depairing current density Jd in the ab plane, while magneto-optical imaging revealed much higher Jc at lower fields. To analyze the experimental data we developed a model of anisotropic vortex pinning which accounts for the observed behavior of Jc in the c-axis tilted films and suggests that the apparent anisotropy of Jc is affected by current pairbreaking effects in the weaker {\pi} band. Our results indicate that the out-of-plane current transport mediated by the {\pi} band could set the ultimate limit of Jc in MgB2 polycrystals.Comment: 21 pges, 13 figure

Magnetic field induced control of breather dynamics in a single plaquette of Josephson junctions

We present a theoretical study of inhomogeneous dynamic (resistive) states in a single plaquette consisting of three Josephson junctions. Resonant interactions of such a breather state with electromagnetic oscillations manifest themselves by resonant current steps and voltage jumps in the current-voltage characteristics. An externally applied magnetic field leads to a variation of the relative shift between the Josephson current oscillations of two resistive junctions. By making use of the rotation wave approximation analysis and direct numerical simulations we show that this effect allows to effectively control the breather instabilities, e. g. to increase (decrease) the height of the resonant steps and to suppress the voltage jumps in the current-voltage characteristics.Comment: 4 pages, 3 figure

Penentration of dynamic localized states in DC-driven Josephson junction ladders by discrete jumps

We give a theoretical study of unusual resistive (dynamic) localized states in anisotropic Josephson junction ladders, driven by a DC current at one edge. These states comprise nonlinearly coupled rotating Josephson phases in adjacent cells, and with increasing current they are found to expand into neighboring cells by a sequence of sudden jumps. We argue that the jumps arise from instabilities in the ladder's superconducting part, and our analytic expressions for the peculiar voltage (rotational frequency) ratios and I-V curves are in very good agreement with direct numerical simulations.Comment: Accepted, Physical Review E. 5 pages, 5 figures. Revtex, with postscript figure

Engineering current density over 5 kA mm-2 at 4.2 K, 14 T in thick film REBCO tapes

We report on remarkably high in-field performance at 4.2 K achieved in >4 μm thick rare earth barium copper oxide (REBCO) samples with Zr addition. Two different samples have been measured independently at Lawrence Berkeley National Laboratory and the National High Magnetic Field Laboratory, achieving critical current densities (J ) of 12.21 MA cm and 12.32 MA cm at 4.2 K, 14 T (), respectively, which corresponds to equivalent critical current (I ) values of 2247 and 2119 A/4 mm. These I values are about two times higher than the best reported performance of REBCO tapes to date and more than five times higher than the commercial HTS tapes reported in a recent study. The measured J values, with a pinning force of ∼1.7 T N m are almost identical to the highest value reported for thin (∼1 μm thick) REBCO at the field and temperature, but extended to very thick (>4 μm) films. This results in an engineering current density (J ) above 5 kA mm at 4.2 K, 14 T, which is more than five times higher than Nb Sn and nearly four times higher than the highest reported value of all superconductors other than REBCO at this field and temperature. The reported results have been achieved by utilizing an advanced metal organic chemical vapor deposition system. This study demonstrates the remarkable level of in-field performance achievable with REBCO conductors at 4.2 K and strong potential for high-field magnet applications. c c c c e 3 -2 -2 -3 -

New Fe-based superconductors: properties relevant for applications

Less than two years after the discovery of high temperature superconductivity in oxypnictide LaFeAs(O,F) several families of superconductors based on Fe layers (1111, 122, 11, 111) are available. They share several characteristics with cuprate superconductors that compromise easy applications, such as the layered structure, the small coherence length, and unconventional pairing, On the other hand the Fe-based superconductors have metallic parent compounds, and their electronic anisotropy is generally smaller and does not strongly depend on the level of doping, the supposed order parameter symmetry is s wave, thus in principle not so detrimental to current transmission across grain boundaries. From the application point of view, the main efforts are still devoted to investigate the superconducting properties, to distinguish intrinsic from extrinsic behaviours and to compare the different families in order to identify which one is the fittest for the quest for better and more practical superconductors. The 1111 family shows the highest Tc, huge but also the most anisotropic upper critical field and in-field, fan-shaped resistive transitions reminiscent of those of cuprates, while the 122 family is much less anisotropic with sharper resistive transitions as in low temperature superconductors, but with about half the Tc of the 1111 compounds. An overview of the main superconducting properties relevant to applications will be presented. Upper critical field, electronic anisotropy parameter, intragranular and intergranular critical current density will be discussed and compared, where possible, across the Fe-based superconductor families