Effects of pH and Temperature on Oilfield Scale Formation

Water flooding is one of the most influential methods for pressure maintenance and enhanced oil recovery. However, water flooding is likely to develop the formation of oilfield scale. Scale formation in reservoirs, due to the mixing of injection water and formation water, could cause formation damage and production limit. Therefore, it is necessary to simulate the compatibility of brine and injection water. Scale prediction is performed using many thermodynamic and/or kinetic based models. In this study, simulations with speciation (ion pairing) are studied, which is a thermodynamic based tool. The utilization of reservoir conditions, formation water analysis, and sea water analysis as the inputs in this method resulted to the accurate prediction of potential scales. In this study, the factors impacting on the scale potential such as pH, temperature, and mixing ratio were also investigated. The obtained results showed that calcite and aragonite were the major scale potential to precipitate. Finally, the results illustrated the important effect of pH and temperature on different scales formation

Experimental investigation into l-Arg and l-Cys eco-friendly surfactants in enhanced oil recovery by considering IFT reduction and wettability alteration

Surfactant flooding is an important technique used to improve oil recovery from mature oil reservoirs due to minimizing the interfacial tension (IFT) between oil and water and/or altering the rock wettability toward water-wet using various surfactant agents including cationic, anionic, non-ionic, and amphoteric varieties. In this study, two amino-acid based surfactants, named lauroyl arginine (l-Arg) and lauroyl cysteine (l-Cys), were synthesized and used to reduce the IFT of oil–water systems and alter the wettability of carbonate rocks, thus improving oil recovery from oil-wet carbonate reservoirs. The synthesized surfactants were characterized using Fourier transform infrared spectroscopy and nuclear magnetic resonance analyses, and the critical micelle concentration (CMC) of surfactant solutions was determined using conductivity, pH, and turbidity techniques. Experimental results showed that the CMCs of l-Arg and l-Cys solutions were 2000 and 4500 ppm, respectively. It was found that using l-Arg and l-Cys solutions at their CMCs, the IFT and contact angle were reduced from 34.5 to 18.0 and 15.4 mN/m, and from 144° to 78° and 75°, respectively. Thus, the l-Arg and l-Cys solutions enabled approximately 11.9% and 8.9% additional recovery of OOIP (original oil in place). It was identified that both amino-acid surfactants can be used to improve oil recovery due to their desirable effects on the EOR mechanisms at their CMC ranges

Geochemical study of the early cretaceous Fahliyan oil reservoir in the northwest Persian Gulf

Three crude oil samples from the Fahliyan Formation in ‘KG’ and ‘F’ fields in the northwest Persian Gulf, namely KG-031, F9A-3H and F15-3H for the geochemical study. In this study, the physicochemical properties, gas chromatography (GC, GC Mass) and (Detailed Hydrocarbon Analysis) DHA analyses for the collected Fahliyan oils were carried out. The API, Trace Element (Ni, V) and S% parameters indicated that the Fahliyan oil was generated from a source rock which deposited in reducing environment condition with a carbonate-shale compound lithology. Moreover, low pour point, higher S% and low viscosity parameters of “KG” sample confirmed the existence of medium oil characteristics in this field. In addition, the geochemical outcomes of GC, GC–MS and DHA analyses indicated that the ‘KG’ oils are more aromatic compared with ‘F’ oil; while biomarkers revealed that Fahliyan reservoir oil is highly mature and was formed from a carbonate source rock containing types II, III kerogen. Thus, sterane/hopane biomarkers (C24/C23 and C22/C21 ratios) revealed that Fahliyan oil originated from carbonate source rocks deposited in an anoxic to dysoxic environment, which is consistent with the above analyses. It was identified that the source rock age is early Cretaceous to late Jurassic. It can be reported that the Fahliyan oils from both fields were generated in the same source rock and have almost the same physical properties, and will have the same production strategy

Application of underbalanced tubing conveyed perforation in horizontal wells: A case study of perforation optimization in a giant oil field in Southwest Iran

Underbalanced perforation can substantially reduce formation damage and improve the efficiency of production operation. The field in question is a giant oil field in Southwest Iran, with over 350,000 bbl/day production rates. Reservoir X is the main reservoir of the field and includes 139 horizontal wells out of the total of 185 production wells drilled in the field. Despite its technical difficulties, under-balance perforation has been proven to result in high productivity ratios and has been shown to reduce workover costs if appropriately conducted. Therefore, this study investigated a customized underbalanced tubing conveyed perforation to enhance oil production. First, post-drilling formation damage was estimated using Perforating Completion Solution Kits. Next, high-density guns (types 73 and 127) with high melting explosives were selected based on the reservoir and well specifications. angles of 60◦ and 90◦ , shot densities of 16 and 20 shots per meter, perforation diameters of By conducting a sensitivity analysis using schlumberger perforating analyzer program, shot 8 and 10 mm, and helix hole distribution were selected as optimized perforation parameters and resulted in productivity ratios up to 1.18. The current study provides a case study of applying a combination of two previously proven technologies, tubing convoyed and underbalanced perforation, in Iran’s giant oilfield. The method used and the outcome could be used to analyze the efficiency of applying the technology in other green or mature fields.Cited as: Mohammadian, E., Dastgerdi, M. E., Manshad, A. K., Mohammadi, A. H., Liu, B., Iglauer, S., Keshavarz, A. Application of underbalanced tubing conveyed perforation in horizontal wells: A case study of perforation optimization in a giant oil field in Southwest Iran. Advances in Geo-Energy Research, 2022, 6(4): 296-305. https://doi.org/10.46690/ager.2022.04.0

Economic and productivity evaluation of different horizontal drilling scenarios: Middle East oil fields as case study

Development of high-density oil and gas fields presents a great challenge to the energy industry due to the low productivity of individual wells and their high drilling cost. We thus compared the productivity, associated costs and economical revenues gained from two field development scenarios, with multilateral and horizontal drilling, to evaluate the optimal drilling and completion conditions in a giant heavy oil reservoir in the Middle East. Well path design was identified as one of the most complex parameters depending on the well-testing results, field production and reservoir simulation data. The fishbone well of four branches with a length of 300 m each and 30° deviation from the main hole was identified to be drilled and completed using open-hole sidetrack as the best approach. The fishbone structure raised production by 393%, while drilling cost only increased by 130% compared with a conventional horizontal well

Insight into nano-chemical enhanced oil recovery from carbonate reservoirs using environmentally friendly nanomaterials

The use of nanoparticles (NPs) in enhanced oil recovery (EOR) processes is very effective in reducing the interfacial tension (IFT) and surface tension (ST) and altering the wettability of reservoir rocks. The main purpose of this study was to use the newly synthesized nanocomposites (KCl / SiO2 / Xanthan NCs) in EOR applications. Several analytical techniques including X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM) were applied to confirm the validity of the synthesized NCs. From the synthesized NCs, nanofluids were prepared at different concentrations of 100-2000 ppm and characterized using electrical conductivity, IFT, and ST measurements. From the obtained results, it can be observed that 1000 ppm is the optimal concentration of the synthesized NCs that had the best performance in EOR applications. The nanofluid with 1000 ppm KCl / SiO2 / Xanthan NCs enabled reducing the IFT and ST from 33 and 70 to 29 and 40 mN/m, respectively. However, the contact angle was highly decreased under the influence of the same nanofluid to 41° and the oil recovery improved by an extra 17.05 % OOIP. To sum up, KCl / SiO2 / Xanthan NCs proved highly effective in altering the wettability of rocks from oil-wet to water-wet and increasing the cumulative oil production

Experimental investigation of the effect of Vitagnus plant extract on enhanced oil recovery process using interfacial tension (IFT) reduction and wettability alteration mechanisms

© 2020, The Author(s). Surfactant flooding is a chemical enhanced oil recovery (cEOR) process wherein anionic, cationic, non-ionic, and amphoteric surfactants are injected into oil reservoirs to produce more hydrocarbon. These chemical and industrial agents might cause some economic and environmental challenges. Recently, injection of natural surfactants, as new environmentally friendly EOR agents, for improving oil recovery has been proposed by researchers. In this study, the extract of Vitagnus, a natural surfactant, was used to minimize the interfacial tension (IFT) and alter the rock wettability towards the strong water-wet system, thereby improving the oil recovery from the carbonate rock The conductivity, pH, and turbidity measurements were undertaken to identify the critical micelle concentration (CMC) of the surfactant solutions prepared by mixing 500, 1000, 2000, 3000, 4000, 5000, 6000, and 7000 ppm of the Vitagnus extract and distilled water. The obtained experimental results reveal that the optimum CMC value of the used surfactant was 3000 ppm. At this CMC value, the IFT reduced from 29.5 to 5.28 mN/m, and the contact angle of the oil droplet on the surface of the carbonate rock decreased from 114° to 29°. Accordingly, during the tertiary process, oil recovery was improved from 44% to 54.6% OOIP (original oil in place) by injecting 2.25 PVs of the VIT3000 surfactant containing 3000 ppm of the plant extract

Effect of environment-friendly non-ionic surfactant on interfacial tension reduction and wettability alteration; Implications for enhanced oil recovery

© 2020 by the authors. Licensee MDPI, Basel, Switzerland. Production from mature oil reservoirs can be optimized by using the surfactant flooding technique. This can be achieved by reducing oil and water interfacial tension (IFT) and modifying wettability to hydrophilic conditions. In this study, a novel green non-ionic surfactant (dodecanoyl-glucosamine surfactant) was synthesized and used to modify the wettability of carbonate reservoirs to hydrophilic conditions as well as to decrease the IFT of hydrophobic oil-water systems. The synthesized non-ionic surfactant was characterized by Fourier transform infrared spectroscopy (FTIR) and chemical shift nuclear magnetic resonance (HNMR) analyses. Further pH, turbidity, density, and conductivity were investigated to measure the critical micelle concentration (CMC) of surfactant solutions. The result shows that this surfactant alters wettability from 148.93° to 65.54° and IFT from 30 to 14 dynes/cm. Core-flooding results have shown that oil recovery was increased from 40% (by water flooding) to 59% (by surfactant flooding). In addition, it is identified that this novel non-ionic surfactant can be used in CO2 storage applications due to its ability to alter the hydrophobicity into hydrophilicity of the reservoir rocks

Synthesis, characterization, and assessment of a CeO2@Nanoclay nanocomposite for enhanced oil recovery

© 2020 by the authors. Licensee MDPI, Basel, Switzerland. In this paper, synthesis and characterization of a novel CeO2 /nanoclay nanocomposite (NC) and its effects on IFT reduction and wettability alteration is reported in the literature for the first time. The NC was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectroscopy (EDS), and EDS MAP. The surface morphology, crystalline phases, and functional groups of the novel NC were investigated. Nanofluids with different concentrations of 100, 250, 500, 1000, 1500, and 2000 ppm were prepared and used as dispersants in porous media. The stability, pH, conductivity, IFT, and wettability alternation characteristics of the prepared nanofluids were examined to find out the optimum concentration for the selected carbonate and sandstone reservoir rocks. Conductivity and zeta potential measurements showed that a nanofluid with concentration of 500 ppm can reduce the IFT from 35 mN/m to 17 mN/m (48.5% reduction) and alter the contact angle of the tested carbonate and sandstone reservoir rock samples from 139◦ to 53◦ (38% improvement in wettability alteration) and 123◦ to 90◦ (27% improvement in wettability alteration), respectively. A cubic fluorite structure was identified for CeO2 using the standard XRD data. FESEM revealed that the surface morphology of the NC has a layer sheet morphology of CeO2/SiO2 nanocomposite and the particle sizes are approximately 20 to 26 nm. TGA analysis results shows that the novel NC has a high stability at 90◦C which is a typical upper bound temperature in petroleum reservoirs. Zeta potential peaks at concentration of 500 ppm which is a sign of stabilty of the nanofluid. The results of this study can be used in design of optimum yet effective EOR schemes for both carbobate and sandstone petroleum reservoirs

Synergistic efficiency of zinc oxide/montmorillonite nanocomposites and a new derived saponin in liquid/liquid/solid interface-included systems: Application in nanotechnology-assisted enhanced oil recovery

Oil production faces challenges such as limited oil production from carbonate reservoirs, high oil production costs, and environmental issues. Chemical flooding as an enhanced oil recovery (EOR) method (CEOR) can increase oil production by the use of chemical additives such as surfactants into the reservoirs. Surfactants can increase oil recovery by interfacial tension (IFT) reduction and alteration of the rock wettability from oil-wet to water-wet. The synthesis of chemicals such as synthetic surfactants is usually costly and harmful to the environment. To solve these problems, many researchers have oriented on the use of natural surfactants instead of synthetic ones within the CEOR process. A new approach to increase the efficiency of CEOR is the synergizing of the chemical additives with nanoparticles as a hybrid fluid, which is known as the nanotechnology-assisted EOR method. In this research, a natural surfactant derived from Cyclamen persicum (CP) plant was extracted, and its performance was optimized with the zinc oxide/montmorillonite (ZnO/MMT) nanocomposite in a synergistic usage. At the optimum concentration of the surfactant, the measurements of the IFT and the contact angle show 57.78 and 61.58 % optimizations, respectively. Also, in the presence of NaCl, the performance of CP is improved. IFT and contact angle measurements were also conducted for ZnO/MMT nanofluids and CP-ZnO/MMT as hybrid nanofluids. Results indicate that ZnO/MMT nanocomposites can alter the wettability of the carbonate rock to the water-wet state. Also, the CP-ZnO/MMT hybrid nanofluid shows a good potential in both IFT reduction and altering wettability from oil-wet to water-wet. Finally, to investigate the effects of solutions on increasing oil recovery factor (RF), the optimum concentrations of the surfactant, nanocomposite, and hybrid solutions were selected for dynamic core flooding experiments, and improvements showed oil RF increases of 8.2, 6, and 13 %, respectively