Mechanical Properties of Hot Rolled Ribbed and Plain Steel Rods

This study focuses on microstructure and mechanical behaviour of 3PS (Semi-killed mild steel) hot rolled ribbed and plain carbon steel. 3PS billet steel samples and hot rolled ribbed and plain steel rods of different heat numbers and profiles were characterized for its chemical composition, microstructure, and tensile behaviour. The composition analysis of 5 (five) 3PS billet samples shows that there was no appreciable variation in chemical composition of the hot-rolled plain and ribbed steel rods. The microstructures of as-received steel billet (3PS) examination revealed large grains of ferrite and pearlite while those of hot-rolled 3 PS mild steel samples of different heat numbers contain smaller grains of ferrite and some amount of pearlite. The results also indicated that yield and ultimate tensile strength reach maximum values (492 and 361 N/mm2) at 0.31% elongation for heat number 43 while maximum values for heat number 56 (478 and 362 N/mm2) at 0.33 % respectively. The ribbed steel rod of the same diameter as plain steel exhibit slightly better mechanical properties with higher values of yield and ultimate tensile strength. There is consistency in the chemical composition of the as-received billet and the hot rolled products

Evaluation of Noise Pollution and Effects on Workers during Wheat Processing

This study assessed the intensity and likely effects of noise on workers during wheat processing. Noise measurements were taken using HD600 sound level meter. Subjective assessment of the effects of noise was undertaken using semi structured questionnaire. Also audiometric test was conducted on workers using AD229e diagnostic audiometer. The results of the study show that during wheat processing operations, the noise level in the factory ranges between 56.0 dB(A) and100.9 dB(A). Also, only 25.6 % of all the readings was below the specified limit of 85 dB(A). Workers are also observed to have certain forms of physiological and psychological disorders related to noise. The audiometric test results revealed that 33 % of the examined workers have defect in their left or right ear. Based on these results, WHO Class-5 hearing protector is recommended to be worn by workers in the processing sections while room acoustics should be upgraded to absorb some sounds transmitted to offices

Determination of the Optimal Tilt Angle for Solar Photovoltaic Panel in Ilorin, Nigeria

The optimal tilt angle of solar photovoltaic panel in Ilorin, Nigeria was determined. The solar panel was first mounted at 0o to the horizontal and after ten minutes, the voltage and current generated with the corresponding atmospheric temperature were recorded. The same procedure was repeated for 2o to 30o at a succession of 2o at ten minutes time interval over the entire measurement period. The result obtained shows that the average optimal tilt angle at which a solar panel will be mounted for maximum power performance at fixed position in Ilorin is 22o. This optimum angle of tilt of the solar panel and the orientation are dependent on the month of the year and the location of the site of study

Hydrokinetic energy resource estimates of River ERO at Lafiagi, Kwara State, North-Central Nigeria

Exploiting the kinetic energy of water currents is considered a smart and cost-effective renewable energy solution without requiring the construction of a dam or of large civil works. Field studies were performed at a selected site along the Ero River, one of the tributaries of River Niger, North-central Nigeria to assess the hydrokinetic energy conversion potentials of the river reach. Relevant data and tools dealing with the hydrology, topography, bathymetry and digital elevation models were used together with year round on-site measurements for the determination of the hydraulic and hydrological parameters. These were used to obtain the instantaneous stream velocities and to compute the power estimates. Preliminary results show that monthly averaged hydrokinetic power of the range 0.034kW-2.3MW can be obtained with the highest values being generated between July and November, with stream velocities above 0.7ms-1. The highest energy value obtainable was 14.76MW while the lowest was 0.11715W. The values also compare well with estimates gleaned from a previous study.Keywords: Hydrokinetic Power, Energy Resource, River Ero, Water Resource

Mechanical Properties Improvement Evaluation of Medium Carbon Steel Quenched in Different Media

The effect of quenching on the mechanical properties of medium carbon steels using coconut (CW) water, pap water (PW) and spent engine oil (SPE) which have been largely considered as wastes was investigated. All specimens were normalized at a temperature of 840°C in order to remove residual stresses induced during machining operations. Various specimens were heated to ranges of 730-790°C and soaked for the range of 30-60 minutes respectively. Brinnel hardness tester was used to obtain the hardness values while Testometric M500-50AT model machine was used for the tensile test of the specimens. The highest hardness value (609.97 BHN) was obtained from the specimen heated to 790°C quenched in pap water as compared with 166.4 BHN for the normalized as-received sample. The yield (YS) and ultimate tensile (UTS) strengths of the quenched specimens were better than the normalized as-received sample. SPEquenched samples yielded the highest YS and UTS combined. The hardness value increased while YS and UTS decreased with soaking time for different temperatures. The highest hardness value for the specimens was obtained from coconut and pap water. Rather than been considered as wastes, coconut water, pap water and spent engine oil can improve the mechanical properties of medium carbon steel when used as quenching media

nical Properties Improvement Evaluation of Medium Carbon Steel Quenched in Different Media

The effect of quenching on the mechanical properties of medium carbon steels using coconut (CW) water, pap water (PW) and spent engine oil (SPE) which have been largely considered as wastes was investigated. All specimens were normalized at a temperature of 840°C in order to remove residual stresses induced during machining operations. Various specimens were heated to ranges of 730-790°C and soaked for the range of 30-60 minutes respectively. Brinnel hardness tester was used to obtain the hardness values while Testometric M500-50AT model machine was used for the tensile test of the specimens. The highest hardness value (609.97 BHN) was obtained from the specimen heated to 790°C quenched in pap water as compared with 166.4 BHN for the normalized as-received sample. The yield (YS) and ultimate tensile (UTS) strengths of the quenched specimens were better than the normalized as-received sample. SPEquenched samples yielded the highest YS and UTS combined. The hardness value increased while YS and UTS decreased with soaking time for different temperatures. The highest hardness value for the specimens was obtained from coconut and pap water. Rather than been considered as wastes, coconut water, pap water and spent engine oil can improve the mechanical properties of medium carbon steel when used as quenching media

Effect of plumage colour on carcass characteristics and meat quality of Nigeria local turkeys

This study examined the effect of plumage colour on carcass characteristics and meat quality of Nigeria local turkeys. Nine 14 weeks local turkeys of different plumage colour (3 blacks, 3 white, and 3 mixed colour) were studied during the experiment. The birds were allotted into treatments based on the 3 plumage colours. Data taken were carcass weight, dressing percentage, prime cuts and relative organs’ weights, pH, drip loss, cook loss, meat colour and sensory attributes of cooked meat. Data collected were subjected to analysis of variance using SPSS version 25. The result obtained revealed that plumage colour affects the pH of turkey meat with a significantly higher carcass pH (5.68) from the mixed colour plumage group. It was also noted that, carcass weight, prime cuts and relative organ weight showed no significant difference (P > 0.05) irrespective of plumage colours. Similarly, the drip loss, cook loss and meat colour (lightness, redness and yellowness) were not influenced by plumage colour of the turkey while the sensory evaluation revealed that black plumaged birds group were more juicy, and had the best aroma and overall acceptability compared to others. It is therefore concluded that plumage colour affects the pH and juiciness, aroma and overall acceptability of Nigeria local turkey meat

Dataset on the evaluation of chemical and mechanical properties of steel rods from local steel plants and collapsed building sites

The quality of steel rods used in structural applications has been subjected to continuous scrutiny by researchers in Nigeria. In this data article, the experimental data on the chemical and mechanical properties of steel rods from collapsed building sites and local steel plants have been reported. The chemical composition consisting of carbon, manganese, silicon, sulphur, phosphorus among other elements were recorded using an optical emission spectrometer. Some of the main elements were used to evaluate the carbon equivalent value and the results are reported in this article. The yield strength, ultimate tensile strength and percentage elongation were also presented as obtained from the universal testing machine. The hardness values of the steel rod samples were also presented. Keywords: Mechanical properties, Collapsed building, Steel rods, Chemical compositions, Percentage elongatio

Dataset on the evaluation of chemical and mechanical properties of steel rods from local steel plants and collapsed building sites

The quality of steel rods used in structural applications has been subjected to continuous scrutiny by researchers in Nigeria. In this data article, the experimental data on the chemical and mechanical properties of steel rods from collapsed building sites and local steel plants have been reported. The chemical composition consisting of carbon, manganese, silicon, sulphur, phosphorus among other elements were recorded using an optical emission spectrometer. Some of the main elements were used to evaluate the carbon equivalent value and the results are reported in this article. The yield strength, ultimate tensile strength and percentage elongation were also presented as obtained from the universal testing machine. The hardness values of the steel rod samples were also presented