3D printing of modified-release aminosalicylate (4-ASA and 5-ASA) tablets

The aim of this study was to explore the potential of fused-deposition 3-dimensional printing (FDM 3DP) to produce modified-release drug loaded tablets. Two aminosalicylate isomers used in the treatment of inflammatory bowel disease (IBD), 5-aminosalicylic acid (5-ASA, mesalazine) and 4-aminosalicylic acid (4-ASA), were selected as model drugs. Commercially produced polyvinyl alcohol (PVA) filaments were loaded with the drugs in an ethanolic drug solution. A final drug-loading of 0.06% w/w and 0.25% w/w was achieved for the 5-ASA and 4-ASA strands, respectively. 10.5mm diameter tablets of both PVA/4-ASA and PVA/5-ASA were subsequently printed using an FDM 3D printer, and varying the weight and densities of the printed tablets was achieved by selecting the infill percentage in the printer software. The tablets were mechanically strong, and the FDM 3D printing was shown to be an effective process for the manufacture of the drug, 5-ASA. Significant thermal degradation of the active 4-ASA (50%) occurred during printing, however, indicating that the method may not be appropriate for drugs when printing at high temperatures exceeding those of the degradation point. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) of the formulated blends confirmed these findings while highlighting the potential of thermal analytical techniques to anticipate drug degradation issues in the 3D printing process. The results of the dissolution tests conducted in modified Hank's bicarbonate buffer showed that release profiles for both drugs were dependent on both the drug itself and on the infill percentage of the tablet. Our work here demonstrates the potential role of FDM 3DP as an efficient and low-cost alternative method of manufacturing individually tailored oral drug dosage, and also for production of modified-release formulations

Fused-filament 3D printing (3DP) for fabrication of tablets

The use of fused-filament 3D printing (FF 3DP) to fabricate individual tablets is demonstrated. The technology permits the manufacture of tablets containing drug doses tailored to individual patients, or to fabrication of tablets with specific drug-release profiles. Commercially produced polyvinyl alcohol (PVA) filament was loaded with a model drug (fluorescein) by swelling of the polymer in ethanolic drug solution. A final drug-loading of 0.29% w/w was achieved. Tablets of PVA/fluorescein (10 mm diameter) were printed using a 3D printer. It was found that changing the degree of infill percentage in the printer software varied the weight and volume of the printed tablets. The tablets were mechanically strong and no significant thermal degradation of the active occurred during printing. Dissolution tests were conducted in modified Hank's buffer. The results showed release profiles were dependent on the infill percentage used to print the tablet. The study indicates that FF 3DP has the potential to offer a new solution for fabricating personalized-dose medicines or unit dosage forms with controlled-release profiles. In addition, the low cost of FDM printers means the paradigm of extemporaneous or point-of-use manufacture of personalized-dose tablets is both feasible and attainable

Ink-jet printing versus solvent casting to prepare oral films: Effect on mechanical properties and physical stability.

The aim of this work was to compare and contrast the mechanical properties and physical stabilities of oral films prepared with either thermal ink-jet printing (TIJP) or solvent casting (SC). Clonidine hydrochloride was selected as a model drug because of its low therapeutic dose and films were prepared using cellulose polymers. Mechanical testing showed that the printed films had Young's moduli and tensile strength values similar to the free film, while casted films were significantly more brittle. The drug also appeared to crystallize out of casted films during stress testing whereas printed films remained unchanged. The dissolution behavior of printed and cast films were similar, because of the rapid disintegration of the polymer. The conclusion is that printing resulted in a better film than casting because the drug resided on the film, rather than in the film where it could exert a plasticizing effect

Emergence of 3D Printed Dosage Forms: Opportunities and Challenges

The recent introduction of the first FDA approved 3D-printed drug has fuelled interest in 3D printing technology, which is set to revolutionize healthcare. Since its initial use, this rapid prototyping (RP) technology has evolved to such as extent that it is currently being used in a wide range of applications including in tissue engineering, dentistry, construction, automotive and aerospace. However, in the pharmaceutical industry this technology is still in its infancy and its potential yet to be fully explored. This paper presents various 3D printing technologies such as stereolithographic, powder based, selective laser sintering, fused deposition modelling and semi-solid extrusion 3D printing. It also provides a comprehensive review of previous attempts at using 3D printing technologies on the manufacturing dosage forms with a particular focus on oral tablets. Their advantages particularly with adaptability in the pharmaceutical field have been highlighted, including design flexibility and control and manufacture which enables the preparation of dosage forms with complex designs and geometries, multiple actives and tailored release profiles. An insight into the technical challenges facing the different 3D printing technologies such as the formulation and processing parameters is provided. Light is also shed on the different regulatory challenges that need to be overcome for 3D printing to fulfil its real potential in the pharmaceutical industry

An Overview of 3D Printing Technologies for Soft Materials and Potential Opportunities for Lipid-based Drug Delivery Systems

Purpose: Three-dimensional printing (3DP) is a rapidly growing additive manufacturing process and it is predicted that the technology will transform the production of goods across numerous fields. In the pharmaceutical sector, 3DP has been used to develop complex dosage forms of different sizes and structures, dose variations, dose combinations and release characteristics, not possible to produce using traditional manufacturing methods. However, the technology has mainly been focused on polymer-based systems and currently, limited information is available about the potential opportunities for the 3DP of soft materials such as lipids. / Methods: This review paper emphasises the most commonly used 3DP technologies for soft materials such as inkjet printing, binder jetting, selective laser sintering (SLS), stereolithography (SLA), fused deposition modeling (FDM) and semi-solid extrusion, with the current status of these technologies for soft materials in biological, food and pharmaceutical applications. / Result: The advantages of 3DP, particularly in the pharmaceutical field, are highlighted and an insight is provided about the current studies for lipid-based drug delivery systems evaluating the potential of 3DP to fabricate innovative products. Additionally, the challenges of the 3DP technologies associated with technical processing, regulatory and material issues of lipids are discussed in detail. / Conclusion: The future utility of 3DP for printing soft materials, particularly for lipid-based drug delivery systems, offers great advantages and the technology will potentially support patient compliance and drug effectiveness via a personalised medicine approach