High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

Circuits and Systems for On-Chip RF Chemical Sensors and RF FDD Duplexers

Integrating RF bio-chemical sensors and RF duplexers helps to reduce cost and area in the current applications. Furthermore, new applications can exist based on the large scale integration of these crucial blocks. This dissertation addresses the integration of RF bio-chemical sensors and RF duplexers by proposing these initiatives. A low power integrated LC-oscillator-based broadband dielectric spectroscopy (BDS) system is presented. The real relative permittivity ε’r is measured as a shift in the oscillator frequency using an on-chip frequency-to-digital converter (FDC). The imaginary relative permittivity ε”r increases the losses of the oscillator tank which mandates a higher dc biasing current to preserve the same oscillation amplitude. An amplitude-locked loop (ALL) is used to fix the amplitude and linearize the relation between the oscillator bias current and ε”r. The proposed BDS system employs a sensing oscillator and a reference oscillator where correlated double sampling (CDS) is used to mitigate the impact of flicker noise, temperature variations and frequency drifts. A prototype is implemented in 0.18 µm CMOS process with total chip area of 6.24 mm^2 to operate in 1-6 GHz range using three dual bands LC oscillators. The achieved standard deviation in the air is 2.1 ppm for frequency reading and 110 ppm for current reading. A tunable integrated electrical balanced duplexer (EBD) is presented as a compact alternative to multiple bulky SAW and BAW duplexers in 3G/4G cellular transceivers. A balancing network creates a replica of the transmitter signal for cancellation at the input of a single-ended low noise amplifier (LNA) to isolate the receive path from the transmitter. The proposed passive EBD is based on a cross-connected transformer topology without the need of any extra balun at the antenna side. The duplexer achieves around 50 dB TX-RX isolation within 1.6-2.2 GHz range up to 22 dBm. The cascaded noise figure of the duplexer and LNA is 6.5 dB, and TX insertion loss (TXIL) of the duplexer is about 3.2 dB. The duplexer and LNA are implemented in 0.18 µm CMOS process and occupy an active area of 0.35 mm^2

UWB FastlyTunable 0.550 GHz RF Transmitter based on Integrated Photonics

Currently, due to the 6G revolution, applications ranging from communication to sensing are experiencing an increasing and urgent need of software-defined ultra-wideband (UWB) and tunable radio frequency (RF) apparatuses with low size, weight, and power consumption (SWaP). Unfortunately, the coexistence of ultra-wideband and software-defined operation, tunability and low SWaP represents a big issue in the current RF technologies. Recently, photonic techniques have been demonstrated to support achieving the desired features when applied in RF UWB transmitters, introducing extremely wide operation and instantaneous bandwidth, tunable filtering, tunable photonics-based microwave mixing with very high port-to-port isolation, and intrinsic immunity to electromagnetic interferences. Moreover, the recent advances in photonics integration also allow to obtain very compact devices. In this article, to the best of our knowledge, the first example of a complete tunable software-defined RF transmitter with low footprint (i.e. on photonic chip) is presented exceeding the state-of-the-art for the extremely large tunability range of 0.5-50 GHz without any parallelization of narrower-band components and with fast tuning (< 200 s). This first implementation represents a breakthrough in microwave photonics

Smart Devices and Systems for Wearable Applications

Wearable technologies need a smooth and unobtrusive integration of electronics and smart materials into textiles. The integration of sensors, actuators and computing technologies able to sense, react and adapt to external stimuli, is the expression of a new generation of wearable devices. The vision of wearable computing describes a system made by embedded, low power and wireless electronics coupled with smart and reliable sensors - as an integrated part of textile structure or directly in contact with the human body. Therefore, such system must maintain its sensing capabilities under the demand of normal clothing or textile substrate, which can impose severe mechanical deformation to the underlying garment/substrate. The objective of this thesis is to introduce a novel technological contribution for the next generation of wearable devices adopting a multidisciplinary approach in which knowledge of circuit design with Ultra-Wide Band and Bluetooth Low Energy technology, realization of smart piezoresistive / piezocapacitive and electro-active material, electro-mechanical characterization, design of read-out circuits and system integration find a fundamental and necessary synergy. The context and the results presented in this thesis follow an “applications driven” method in terms of wearable technology. A proof of concept has been designed and developed for each addressed issue. The solutions proposed are aimed to demonstrate the integration of a touch/pressure sensor into a fabric for space debris detection (CApture DEorbiting Target project), the effectiveness of the Ultra-Wide Band technology as an ultra-low power data transmission option compared with well known Bluetooth (IR-UWB data transmission project) and to solve issues concerning human proximity estimation (IR-UWB Face-to-Face Interaction and Proximity Sensor), wearable actuator for medical applications (EAPtics project) and aerospace physiology countermeasure (Gravity Loading Countermeasure Skinsuit project)

Ultra-Wideband Transceiver with Error Correction for Cortical Interfaces in NanometerCMOS Process

This dissertation reports a high-speed wideband wireless transmission solution for the tight power constraints of cortical interface application. The proposed system deploysImpulse Radio Ultra-wideband (IR-UWB) technique to achieve very high-rate communication. However, impulse radio signals suffer from significant attenuation within the body,and power limitations force the use of very low-power receiver circuits which introduce additional noise and jitter. Moreover, the coils’ self-resonance has to be suppressed to minimize the pulse distortion and inter-symbol interference, adding significant attenuation. To compensate these losses, an Error correction code (ECC) layer is added for functioning reliably to the system. The performance evaluation is made by modeling a pair of physically fabricated coils, and the results show that the ECC is essential to obtain the system’s reliability. Furthermore, the gm/ID methodology, which is based on the complete exploration ofall inversion regions that the transistors are biased, is studied and explored for optimizingthe system at the circuit-level. Specific focuses are on the RF blocks: the low noise am-plifier (LNA) and the injection-locked voltage controlled oscillator (IL-VCO). Through the analytical deduction of the circuit’s features as the function of the gm/ID for each transistor, it is possible to select the optimum operating region for the circuit to achieve the target specification. Other circuit blocks, including the phase shifter, frequency divider,mixer, etc. are also described and analyzed. The prototype is fabricated in a 65-nm CMOS(Complementary Metal-Oxide-Semiconductor) process

Novel RF CMOS Integrated Circuits and Systems for Broadband Dielectric Spectroscopy

Broadband dielectric spectroscopy has proven to be a valuable technique for characterization of chemicals and biomaterials. It has the great potential to become an indispensable and cost-effective tool in point-of-care medical applications due to its label-free and non-invasive operation. However, most of the existing dielectric spectroscopy instruments require bulky, heavy and expensive measurement set-up, restricting their use to only special applications in industry and laboratories. Therefore, integrated dielectric spectroscopy on silicon capable of direct detection of chemicals/biomaterials' complex permittivity can yield significant cost and size reduction, system integration, portability, enormous processing, and high throughput. A CMOS wideband dielectric spectroscopy system is proposed for chemical and biological material characterization. The complex permittivity detection is performed using a configurable harmonic-rejecting receiver capable of indirectly measuring the complex admittance of sensing capacitor exposed to the material-under-test (MUT) and subject to RF signal excitation with a frequency range of 0.62-10 GHz. The sensing capacitor is embedded in a voltage divider topology with a fixed capacitor and the relative variations in the magnitude and phase of the voltages across the capacitors are used to find the real and imaginary parts of the permittivity. The sensor achieves an rms permittivity error of less than 1% over the entire operation bandwidth. Using a sub-harmonic mixing scheme, the system can perform complex permittivity measurements from 0.62 to 10 GHz while requiring an input signal source with frequency range of only from 5 to 10 GHz. Thereby, the permittivity measurement system can be easily made self-sustained by implementing a 5-10 GHz frequency synthesizer on the same chip. One of the key building blocks in such a frequency synthesizer is the voltage-controlled oscillator (VCO) which has to cover an octave of frequency range. A novel low-phase-noise wide-tuning range VCO is presented using a triple-band LC resonator. The implemented VCO in 0.18μm CMOS technology achieves a continuous tuning range of 86.7% from 5.12 GHz to 12.95 GHz while drawing 5 to 10 mA current from 1-V supply. The measured phase noise at 1 MHz offset from carrier frequencies of 5.9, 9.12 and 12.25 GHz is -122.9, -117.1 and -110.5 dBc/Hz, respectively. Also, a dual-band quadrature voltage-controlled oscillator (QVCO) is presented using a transformer-based high-order LC-ring resonator which inherently provides quadrature signals without requiring noisy coupling transistors as in traditional approaches. The proposed resonator shows two possible oscillation frequencies which are exploited to realize a wide-tuning range QVCO employing a mode-switching transistor network. Due to the use of transformers, the oscillator has minimal area penalty compared to the conventional designs. The implemented prototype in a 65-nm CMOS process achieves a continuous tuning range of 77.8% from 2.75 GHz to 6.25 GHz while consuming 9.7 to 15.6 mA current from 0.6-V supply. The measured phase noise figure-of-merit (FoM) at 1 MHz offset ranges from 184 dB to 188.2 dB throughout the entire tuning range. The QVCO also exhibits good quadrature accuracy with 1.5º maximum phase error and occupies a relatively small silicon area of 0.35 mm^2

Analysis And Design Of Wideband Passive Mixer-First Receivers

This dissertation focuses on the design of wideband SAW-less receivers for softwaredefined radios. The entire body of work is based on a single RF front-end architecture type: a passive mixer connected directly to the antenna port of the radio, without an LNA or matching network up front. This structure is inherently wideband which allows for a single receiver front-end to operate at a wide range of frequencies, as tuned by its local oscillator (LO). Additionally, the mixer exhibits the property of transparency from the baseband port of the radio to the RF port of the radio, and vice versa. The focus of the first half of the thesis is on developing a simple theoretical framework for the impedance characteristics of the passive mixer, and implementing a maximally flexible receiver which utilizes the mixer's transparency to the fullest extent. Additionally, it is shown that mixing with 8 non-overlapping phases instead of the traditional 4 has benefits beyond harmonic rejection extending to improved noise performance and increased impedance tuning range. This receiver exhibits low noise figure (~3dB), excellent wideband linearity (IIP3[GREATER-THAN OR EQUAL TO]25dBm), and unprecedented RF impedance control from the baseband side of the passive mixer. Another wideband receiver is presented which explores increasing the number of LO phases even further to 16 and 32, increasing the impedance matching range. The same chip contains a circuit technique for alleviating the shunting effects of LO phase overlap on mixer conversion gain, noise, and impedance match range. Finally in a new design, the power consumption of the receiver architecture is decreased by a factor of 5x (and not scaling with RF frequency). This is done using a resonant LO drive with 8 non-overlapping phases, incorporating the large mixer gate capacitance directly into the LC tank of the VCO. Baseband power consumption is also reduced by reusing current in the four baseband amplifier channels, and performing harmonic rejection, all in one stage of amplification

Integrated RF oscillators and LO signal generation circuits

This thesis deals with fully integrated LC oscillators and local oscillator (LO) signal generation circuits. In communication systems a good-quality LO signal for up- and down-conversion in transmitters is needed. The LO signal needs to span the required frequency range and have good frequency stability and low phase noise. Furthermore, most modern systems require accurate quadrature (IQ) LO signals. This thesis tackles these challenges by presenting a detailed study of LC oscillators, monolithic elements for good-quality LC resonators, and circuits for IQ-signal generation and for frequency conversion, as well as many experimental circuits. Monolithic coils and variable capacitors are essential, and this thesis deals with good structures of these devices and their proper modeling. As experimental test devices, over forty monolithic inductors and thirty varactors have been implemented, measured and modeled. Actively synthesized reactive elements were studied as replacements for these passive devices. At first glance these circuits show promising characteristics, but closer noise and nonlinearity analysis reveals that these circuits suffer from high noise levels and a small dynamic range. Nine circuit implementations with various actively synthesized variable capacitors were done. Quadrature signal generation can be performed with three different methods, and these are analyzed in the thesis. Frequency conversion circuits are used for alleviating coupling problems or to expand the number of frequency bands covered. The thesis includes an analysis of single-sideband mixing, frequency dividers, and frequency multipliers, which are used to perform the four basic arithmetical operations for the frequency tone. Two design cases are presented. The first one is a single-sideband mixing method for the generation of WiMedia UWB LO-signals, and the second one is a frequency conversion unit for a digital period synthesizer. The last part of the thesis presents five research projects. In the first one a temperature-compensated GaAs MESFET VCO was developed. The second one deals with circuit and device development for an experimental-level BiCMOS process. A cable-modem RF tuner IC using a SiGe process was developed in the third project, and a CMOS flip-chip VCO module in the fourth one. Finally, two frequency synthesizers for UWB radios are presented