Wideband Filtering Power Divider With Ultra-Wideband Harmonic Suppression and Isolation

In this paper, a wideband filtering power divider (PD) with ultra-wideband harmonic suppression and isolation is proposed. The dual coupled-line sections are embedded to the conventional quarter-wavelength transmission lines, which helps to extend the passband of the PD. With the introduction of the short-circuit stubs shunted at the output ports and the coupled lines with the open-circuit stubs, the ultra-wide stopband can be implemented more efficiently, thus resulting in five transmission zeros from 2 to 6 GHz. Furthermore, the improved isolation structure with series connected a resistor and a capacitor can be utilized to realize the ultra-wide isolation frequency band. Using a single resistor between two output ports, we have achieved an excellent in-band isolation. For demonstration, a wideband filtering PD operating at 1 GHz with a 20-dB bandwidth of 50% and an ultra-wide stopband better than 20 dB from 2 to 6 GHz is designed, fabricated, and measured. The measured results agree well with the anticipation

Wideband bandpass-to-all-stop reconfigurable filtering power divider with bandwidth control and all-passband isolation

A novel wideband bandpass-to-all-stop reconfigurable filtering power divider is proposed in this study, which allows for four-order bandpass-to-all-stop reconfigurable operating function and equal power division. Its circuit configuration includes the cascaded coupled-line sections with tight coupling to extend the impedance transforming. Furthermore, with the introduction of the half-wavelength open-circuit stubs, which controls the bandwidth, extra transmission poles located at the cut-off frequency are generated, thus resulting in high frequency selectivity. Moreover, by using a single resistor between input coupled-lines, the high all-passband isolation can be achieved. The grounding are then loaded to the output coupled-lines to enable bandpass-to-all-stop operating functionality. For demonstration, a prototype operating at 2 GHz is designed, simulated, and measured with a 15 dB bandwidth of 51%, 19 dB stopband rejection up to 5 GHz, and 14.5 dB all-passband isolation, which shows a good agreement between the simulated and measured results

A 3 dB Microstrip Power Divider at 2.2 GHz with Floating Metals

In this paper, a solid, inexpensive power divider of 2.2 GHz with a low-pass filtering response is proposed, analyzed and designed. Following results have been achieved, S11 -14.7 dB, S12 -3.318 dB, S13 -3.008 dB. Design is based on the vertical slits around the corners, and eight floating parallel metals that keep the divider in current free state. It is symmetrical along the middle which provides significant compatibility in manufacturing process. Can be used within microwave band of frequencies in 2-4 GHz spectrum band in electromagnetics. Provides substantial stability and reliability in its working domain

Design of wideband in-phase and out-of-phase power dividers using microstrip-to-slotline transitions and slotline resonators

© 2019 IEEE. A new class of in-phase and out-of-phase power dividers with constant equal-ripple frequency response and wide operating bandwidth is presented in this paper. The proposed design is based on microstrip-to-slotline transitions and slotline resonators. A slotted T-junction is adopted to split the power into two parts and obtain wideband isolation between the two output signals at the same time. The characteristic impedance of the transitions and resonators determines the operating bandwidth and in-band magnitude response. By reversing the placement direction of the slotline-to-microstrip transition, the electrical field is reversed, thus resulting in out-of-phase responses between output ports. A thorough analysis of the relations between the structure and the characteristic functions is provided to guide the selection of parameters of the structure in order to meet the design objectives. In the structure, simulation and measurement are conducted to verify the design method. For both in-phase and out-of-phase cases, more than 110% bandwidth has been achieved with excellent matching at all ports and isolation of output signals. Constant in-band ripple is obtained within the operating band of the power dividers, indicating that the proposed design can realise minimal power deviations, which is extremely desired in wireless systems

Novel Compact Three-Way Filtering Power Divider Using Net-Type Resonators

In this paper, we present a novel compact three-way power divider with bandpass responses. The proposed power divider utilizes folded net-type resonators to realize dual functions of filtering and power splitting as well as compact size. Equal power ratio with low magnitude imbalance is achieved due to the highly symmetric structure. For demonstration, an experimental three way filtering power divider is implemented. Good filtering and power division characteristics are observed in the measured results of the circuit. The area of the circuits is 14.5 mm x 21.9 mm or 0.16 λg x 0.24 λg, where the λg is the guide wavelength of the center frequency at 2.1 GHz

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Compact tri-band Wilkinson power divider based on metamaterial structure for Bluetooth, WiMAX, and WLAN applications

A novel Wilkinson power divider is presented in this paper for triple band operation. It comprises a П-shaped transmission-line coupled to a rectangular split ring resonator metamaterial structure. The μ-negative feature of the rectangular split ring resonator metamaterial structure is investigated by retrieving its constitutive parameters from the S-parameter response. To demonstrate the versatility of the proposed Wilkinson power divider it was designed to cover Bluetooth (2.4 GHz), WiMAX (3.5 GHz), and WLAN (5.2 GHz). The tri-band Wilkinson power divider was fabricated and its performance measured to verify the design. Good agreement between the measured and simulated data is obtained. Measured results show that the tri-band Wilkinson power divider has fractional bandwidth of 3.86%, 5.82%, and 3.89% at 2.4, 3.5, and 5.2 GHz, respectively. In addition, the rectangular split ring resonator metamaterial Wilkinson power divider has a small physical footprint (14 mm ×17.9 mm or 0.15λg×0.19λg), which is 60% smaller than conventional designs