Synchronization of a WDM Packet-Switched Slotted Ring

In this paper, we present two different strategies of slot synchronization in wavelength-division-multiplexing (WDM) packet-switched slotted-ring networks. Emphasis is given to the architecture behind the WDM Optical Network Demonstrator over Rings (WONDER) project, which is based on tunable transmitters and fixed receivers. The WONDER experimental prototype is currently being developed at the laboratories of Politecnico di Torino. In the former strategy, a slotsynchronization signal is transmitted by the master station on a dedicated control wavelength; in the latter, slave nodes achieve slot synchronization aligning on data packets that are received from the master. The performance of both synchronization strategies, particularly in terms of packet-collision probability, was evaluated by simulation. The technique based on transmitting a timing signal on a dedicated control wavelength achieves better performance, although it is more expensive due to the need for an additional wavelength. However, the technique based on aligning data packets that are received from the master, despite attaining lower timing stability, still deserves further study, particularly if limiting the number of wavelengths and receivers is a major requirement. Some experimental results, which were measured on the WONDER prototype, are also shown. Measurement results, together with theoretical findings, demonstrate the good synchronization performance of the prototype

A high-speed optical star network using TDMA and all-optical demultiplexing techniques

The authors demonstrate the use of time-division multiplexing (TDM) to realize a high capacity optical star network. The fundamental element of the demonstration network is a 10 ps, wavelength tunable, low jitter, pulse source. Electrical data is encoded onto three optical pulse trains, and the resultant low duty cycle optical data channels are multiplexed together using 25 ps fiber delay lines. This gives an overall network capacity of 40 Gb/s. A nonlinear optical loop mirror (NOLM) is used to carry out the demultiplexing at the station receiver. The channel to be switched out can be selected by adjusting the phase of the electrical signal used to generate the control pulses for the NOLM. By using external injection into a gain-switched distributed feedback (DFB) laser we are able to obtain very low jitter control pulses of 4-ps duration (RMS jitter <1 ps) after compression of the highly chirped gain switched pulses in a normal dispersive fiber. This enables us to achieve excellent eye openings for the three demultiplexed channels. The difficulty in obtaining complete switching of the signal pulses is presented. This is shown to be due to the deformation of the control pulse in the NOLM (caused by the soliton effect compression). The use of optical time-division multiplexing (OTDM) with all-optical switching devices is shown to be an excellent method to allow us to exploit as efficiently as possible the available fiber bandwidth, and to achieve very high bit-rate optical networks

Power Control In Optical CDMA

Optical CDMA (OCDMA) is the multiplexing technique over the fiber optics medium to increase the number of users and this is a step towards all optical Passive Optical Networks (PON). Optical OFDM, WDM and Optical TDM have also been studied in this thesis which are also candidates to all optical passive optical networks. One of the main features of Optical CDMA over other multiplexing techniques is that it has smooth capacity. The capacity of OCDMA is constrained by the interference level. Hence, when some users are offline or requesting less data rates, then the capacity will be increased in the network. Same feature could be obtained in other multiplexing techniques, but they will need much more complicated online organizers. However, in OCDMA it is critical to adjust the transmission power to the right value; otherwise, near-far problem may greatly reduce the network capacity and performance. In this thesis Power control concepts are analyzed in optical CDMA star networks. It is applied so that the QoS of the network get enhanced and all users after the power control have their desired signal to interference (SIR) value. Moreover, larger number of users can be accommodated in the network. Centralized power control algorithm is considered for this thesis. In centralized algorithm noiseless case and noisy case have been studied. In this thesis several simulations have been performed which shows the QoS difference before and after power control. The simulation results are validated also by the theoretical computation.fi=Opinnäytetyö kokotekstinä PDF-muodossa.|en=Thesis fulltext in PDF format.|sv=Lärdomsprov tillgängligt som fulltext i PDF-format

Simulation of 1 x 2 OTDM router employing symmetric Mach-Zehnder switches

In high-speed all-optical time division multiplexed (OTDM) routers it is desirable to carry out data routing, switching, clock recovery and synchronisation in the optical domain in order to avoid the bottleneck due to optoelectronics conversion. The authors propose an optical switch based on all-optical symmetric Mach–Zehnder (SMZ) switching and investigate its characteristics. The proposed switch is to be used as a building block for a simple 1x2 OTDM router for asynchronous OTDM packet routing, where clock recovery, address recognition and payload routing are all carried out in the optical domain. Simulation and numerical results demonstrate that clock recovery, address recognition and payload routing are possible with small amounts of crosstalk. Also presented are simulation results for bit error rate (BER) performance for the 1x2 router. For a BER of 10e-9 the receiver sensitivity is -26 dB compared with baseline detection without a router of -38 dB. The proposed router displays great potential for use in ultrahigh- speed OTDM networks

BER performance analysis of 100 and 200 Gbit/s all-optical OTDM node using symmetric Mach-Zehnder switches

New insight to the feasibility of all-optical ultra speed switching up to 200 Gb/s. The technique will reduce the dependency and bottleneck on the electronic-to-optical-to-electronic conversion. Current conversion speed is up to 40 Gb/s in laboratories. The novel clock extraction technique proposed shows the potential of an all-optical switch. The research results are directly relevant to the access technology where optical fibre and RF is competing to be the solution. The growing demands of bandwidth will exceed RF capability while the optical fibre will be the optimum solution. A PhD project (Le-Minh) funded by the University Studentship, completed in 2007

Fully-photonic digital radio over fibre for future super-broadband access network applications

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel UniversityIn this thesis a Fully-Photonic DRoF (FP-DRoF) system is proposed for deploying of future super-broadband access networks. Digital Radio over Fibre (DRoF) is more independent of the fibre network impairments and the length of fibre than the ARoF link. In order for fully optical deployment of the signal conversion techniques in the FP-DRoF architecture, two key components an Analogue-to-Digital Converter (ADC) and a Digital-to-Analogue Converter (DAC)) for data conversion are designed and their performance are investigated whereas the physical functionality is evaluated. The system simulation results of the proposed pipelined Photonic ADC (PADC) show that the PADC has 10 GHz bandwidth around 60 GHz of sampling rate. Furthermore, by changing the bandwidth of the optical bandpass filter, switching to another band of sampling frequency provides optimised performance condition of the PADC. The PADC has low changes on the Effective Number of Bit (ENOB) response versus analogue RF input from 1 GHz up to 22 GHz for 60 GHz sampling frequency. The proposed 8-Bit pipelined PADC performance in terms of ENOB is evaluated at 60 Gigasample/s which is about 4.1. Recently, different methods have been reported by researchers to implement Photonic DACs (PDACs), but their aim was to convert digital electrical signals to the corresponding analogue signal by assisting the optical techniques. In this thesis, a Binary Weighted PDAC (BW-PDAC) is proposed. In this BW-PDAC, optical digital signals are fully optically converted to an analogue signal. The spurious free dynamic range at the output of the PDAC in a back-to-back deployment of the PADC and the PDAC was 26.6 dBc. For further improvement in the system performance, a 3R (Retiming, Reshaping and Reamplifying) regeneration system is proposed in this thesis. Simulation results show that for an ultrashort RZ pulse with a 5% duty cycle at 65 Gbit/s using the proposed 3R regeneration system on a link reduces rms timing jitter by 90% while the regenerated pulse eye opening height is improved by 65%. Finally, in this thesis the proposed FP-DRoF functionality is evaluated whereas its performance is investigated through a dedicated and shared fibre links. The simulation results show (in the case of low level signal to noise ratio, in comparison with ARoF through a dedicated fibre link) that the FP-DRoF has better BER performance than the ARoF in the order of 10-20. Furthermore, in order to realize a BER about 10-25 for the ARoF, the power penalty is about 4 dBm higher than the FP-DRoF link. The simulation results demonstrate that by considering 0.2 dB/km attenuation of a standard single mode fibre, the dedicated fibre length for the FP-DRoF link can be increased to about 20 km more than the ARoF link. Moreover, for performance assessment of the proposed FP-DRoF in a shared fibre link, the BER of the FP-DRoF link is about 10-10 magnitude less than the ARoF link for -19 dBm launched power into the fibre and the power penalty of the ARoF system is 10 dBm more than the FP-DRoF link. It is significant to increase the fibre link’s length of the FP-DRoF access network using common infrastructure. In addition, the simulation results are demonstrated that the FP-DRoF with non-uniform Wavelength Division Multiplexing (WDM) is more robust against four wave mixing impairment than the conventional WDM technique with uniform wavelength allocation and has better performance in terms of BER. It is clearly verified that the lunched power penalty at CS for DRoF link with uniform WDM techniques is about 2 dB higher than non-uniform WDM technique. Furthermore, uniform WDM method requires more bandwidth than non-uniform scheme which depends on the total number of channels and channels spacing

Research of the optical communications groups at University of Aveiro and Institute of Telecommunications - Aveiro Pole

This paper summarizes the research activities of the optical communications group at University of Aveiro and Institute of Telecommunications – Aveiro pole. Several activities like clock recovery systems, both electrical and all optical, electrical equalizers for very high bit rate DST systems, post-detection filters for multigigabit optical receivers, soliton systems, simulation work on WDM, DST, EDFA and short pulse generation for high bit rate systems are presented

Analysis of jitter impact on high speed transmissions of wavelength-division multiplexing networks

In this study, we conduct a thorough assessment of the effect of jitter occurrence in high speed 10 Gbps and 200 GHz Wavelength-Division Multiplexing (WDM) optical network. First, we present a simulation model to study the effect of jitter presence in the proposed network and then determine the maximum amount of jitter which the network can withstand. The model is then employed to predict the types of jitter received at the end of the transmission line. For the input power level of 0 dBm and Bit Error Rate (BER) of 1E09, the observed total jitter, JT, random jitter, JR and deterministic jitter, JD is 0.2676 UI, 0.1602 UI and 0.1073 UI, respectively