Subcarrier and Power Allocation for LDS-OFDM System

Low Density Signature-Orthogonal Frequency Division Multiplexing (LDS-OFDM) has been introduced recently as an efficient multiple access technique. In this paper, we focus on the subcarrier and power allocation scheme for uplink LDS-OFDM system. Since the resource allocation problem is not convex due to the discrete nature of subcarrier allocation, the complexity of finding the optimal solutions is extremely high. We propose a heuristic subcarrier and power allocation algorithm to maximize the weighted sum-rate. The simulation results show that the proposed algorithm can significantly increase the spectral efficiency of the system. Furthermore, it is shown that LDS-OFDM system can achieve an outage probability much less than that for OFDMA system

Fifty Years of Noise Modeling and Mitigation in Power-Line Communications.

Building on the ubiquity of electric power infrastructure, power line communications (PLC) has been successfully used in diverse application scenarios, including the smart grid and in-home broadband communications systems as well as industrial and home automation. However, the power line channel exhibits deleterious properties, one of which is its hostile noise environment. This article aims for providing a review of noise modeling and mitigation techniques in PLC. Specifically, a comprehensive review of representative noise models developed over the past fifty years is presented, including both the empirical models based on measurement campaigns and simplified mathematical models. Following this, we provide an extensive survey of the suite of noise mitigation schemes, categorizing them into mitigation at the transmitter as well as parametric and non-parametric techniques employed at the receiver. Furthermore, since the accuracy of channel estimation in PLC is affected by noise, we review the literature of joint noise mitigation and channel estimation solutions. Finally, a number of directions are outlined for future research on both noise modeling and mitigation in PLC

Reducing the Peak to Average Power Ratio of LDS-OFDM signals

Low Density Signature-Orthogonal Frequency Division Multiplexing (LDS-OFDM) has been introduced recently as an efficient multiple access technique. High Peak to Average Power Ratio (PAPR) is an important obstacle to multicarrier communication systems. This paper concentrates on the PAPR investigation and its reduction for LDS-OFDM signals. Specifically, we will investigate the impact of subcarrier allocation schemes and the phases of the signatures on the PAPR of LDS-OFDM signals. Firstly, the PAPR of LDS-OFDM with conventional signatures is investigated. Then we propose two methods for PAPR reduction; Newman phases and DFT pre-coding. The former method is simple and doesn't imply changes in the system structure while the DFT pre-coding implies a modification in the system. Simulation results show that using Newman phases considerably reduces the PAPR of LDS-OFDM. Further PAPR reduction is achieved using DFT pre-coded LDS-OFDM on the cost of higher complexity

잔향 환경에서의 인공 음향 신호를 이용한 음향 센서 위치 추정 기술

학위논문 (박사)-- 서울대학교 대학원 공과대학 전기·컴퓨터공학부, 2017. 8. 김남수.Widespread use of smart devices has brought a growth of user-customized services. In particular, localization techniques have been gaining attention due to increase of location-based services (LBS). Most of LBS services such as navigation systems, traffic alerts or augmented reality (AR) services depend on the GPS for its accuracy and speed, however, its operation is limited to the outdoor environments. The demand of indoor LBS is rapidly growing due to the growth of automated home and IoT technology. There have been studies via WiFi, Bluetooth or RFID, but their performance has been unsatisfactory for their limitation such as the requirement of additional equipment or guarantee of the line of sight. Among various sensors used for indoor localization, we focus on the acoustic sensors, i.e. microphones. There are several advantages in using the acoustic signals for indoor localization. There is no need for additional apparatus since loudspeakers are pre-installed in most of the buildings for the purpose of announcement or playing background music and mobile devices such as cellphones or tablets are equipped with microphones and loudspeakers. Even the prevailing popularity of IoT services helps accessibility of acoustical sensors and loudspeakers. In addition, acoustic signals have advantages of being able to detect signals through obstacles unlike cameras of RFID. In this thesis, we propose a position estimation system using acoustic signals to maximize these advantages. We aim to estimate the position of the target user with an acoustic sensor based on the recording of signals from the fixed loudspeakers installed around the room. We target to estimate the position of the acoustic sensor with high accuracy and low-complexity in a large space with high reverberation. Particularly, we try not to affect human hearing by using inaudible frequency bands. In order to estimate the position, it is important to estimate the direct path signal rather than the signal due to reverberation or reflection. To do this, we present various localization techniques as following. First, we propose the source data structure to operate in the large reverberant environments. In the large space, the consideration of the near-far effect is required which refers to a situation when the desired signal is far away, it is difficult to receive the desired signal due to the interference of closer unwanted signals. In wireless communications, it can be dealt with by interaction of transmitter and receiver by feedback of channel information. However, it is difficult in the acoustic system since there is no feedback between the transmitter and receiver. We borrowed the structure called OFDMA-CDM and modified it to deal with the near-far effect. In the reverberant environment, the amplitude of reverberation is often larger than the direct path signal. We proposed the technique to estimate the direct path signal. Second, we propose a method for accurate location estimation in the highly reverberant environments. In the high reverberation condition, more spurious reflections occur, which makes it difficult to estimate the time delay of the direct path signal. If the time delay estimation is wrong, it is likely that the position estimate does not converge by an estimation method. In the proposed method, position candidates are obtained from most of the received signals including signals even from spurious reflections. The unreliable candidates are filtered out by the agreement test and rank the rest candidates by their reliability to find accurate target position. We can estimate the receiver's position even in the condition of attenuated direct path signal or high reverberation by using the proposed method. Third, we proposed a low-complexity localization method to work in the highly reverberant environment. This method is based on the particle filter that estimates the position by weighted particles whose weights are computed by the likelihood. We designed likelihood function that efficiently calculates likelihood in the region with the direct path signal so that more reliable position can be obtained. The proposed method enables location estimation with high precision with a relatively small amount of computation in severe reverberation. The proposed methods are evaluated in simulated environments with different reverberation time. The performances are verified in different parameters and compared with other localization methods. In addition, the performance is evaluated in the real reverberant environment with a large space. A series of experiments has shown the superiority of the proposed methods and it is appropriate to apply in the actual environment.1 Introduction 1 2 Acoustic Receiver Localization System 7 2.1 Source data structure 8 2.2 Localization from the received signal 12 2.3 TDE in reverberant environments 16 2.4 Near-far effect 18 3 Indoor Localization using Inaudible Acoustic Signals 21 3.1 Introduction 21 3.2 Acoustic source design and synchronization 22 3.2.1 Reverberation in multipath environments 23 3.2.2 Source data structure for ARL 23 3.2.3 Signal presence detection 30 3.2.4 Direct path detection 30 3.3 Performance evaluation 32 3.3.1 Experimental setup and system configuration 33 3.3.2 Evaluation of acoustic data structure 34 3.3.3 Performance of the direct path detection algorithm 36 3.3.4 Performance in a real room 36 3.4 Summary 38 4 Robust Time Delay Estimation for Acoustic Indoor Localization in Reverberant Environments 39 4.1 Introduction 39 4.2 Robust TDE 40 4.3 Performance evaluation 45 4.3.1 Performance evaluation in a real room 46 4.3.2 Performance evaluation in simulated reverberant conditions 47 4.4 Summary 50 5 Indoor Localization Based on Particle Filtering 53 5.1 Introduction 53 5.2 A framework of positioning method using particle filter 54 5.2.1 State and dynamic models 55 5.2.2 Bayesian framework using particle filter 56 5.2.3 Likelihood function 57 5.3 ARL in reverberant environment 59 5.3.1 Peak quality 59 5.3.2 Efficient calculation of the likelihood function 60 5.3.3 Finding the direct path region 61 5.4 Performance evaluation 64 5.4.1 Performance in a simulated environment 65 5.4.2 Performance in the actual environment 87 5.5 Summary 89 6 Conclusions 91 Bibliography 95 요약 105Docto

Iterative Detection for Overloaded Multiuser MIMO OFDM Systems

Inspired by multiuser detection (MUD) and the ‘Turbo principle’, this thesis deals with iterative interference cancellation (IIC) in overloaded multiuser multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) systems. Linear detection schemes, such as zero forcing (ZF) and minimum mean square error (MMSE) cannot be used for the overloaded system because of the rank deficiency of channel matrix, while the optimal approach, the maximum likelihood (ML) detection has high computational complexity. In this thesis, an iterative interference cancellation (IIC) multiuser detection scheme with matched filter and convolutional codes is considered. The main idea of this combination is a low complexity receiver. Parallel interference cancellation (PIC) is employed to improve the multiuser receiver performance for overloaded systems. A log-likelihood ratio (LLR) converter is proposed to further improve the reliability of the soft value converted from the output of the matched filter. Simulation results show that the bit error rate (BER) performance of this method is close to the optimal approach for a two user system. However, for the four user or more user system, it has an error floor of the BER performance. For this case, a channel selection scheme is proposed to distinguish whether the channel is good or bad by using the mutual information based on the extrinsic information transfer (EXIT) chart. The mutual information can be predicted in a look-up table which greatly reduces the complexity. For those ‘bad’ channels identified by the channel selection, we introduce two adaptive transmission methods to deal with such channels: one uses a lower code rate, and the other is multiple transmissions. The use of an IIC receiver with the interleave-division multiple access (IDMA) to further improve the BER performance without any channel selection is also investigated. It has been shown that this approach can remove the error floor. Finally, the influence of channel accuracy on the IIC is investigated. Pilot-based Wiener filter channel estimation is used to test and verify how much the IIC is influenced by the channel accuracy

New concepts for EMC standards applicable to multimedia products

In het vakgebied van Elektromagnetische Compatibiliteit (EMC) kunnen globaal twee fenomenen beschouwd worden: de emissie en de immuniteit van elektronische producten.\ud Emissiemetingen van elektronische producten worden uitgevoerd voor de bescherming van radio systemen. We spreken van een emissiemeting via geleiding als er een stroom wordt gemeten en van een meting van emissie via straling als een elektromagnetische veldgrootheid gemeten wordt. Immuniteitstesten worden uitgevoerd om elektronische producten te testen op de bestendigheid tegen elektromagnetische stoorsignalen