Robot Impedance Control and Passivity Analysis with Inner Torque and Velocity Feedback Loops

Impedance control is a well-established technique to control interaction forces in robotics. However, real implementations of impedance control with an inner loop may suffer from several limitations. Although common practice in designing nested control systems is to maximize the bandwidth of the inner loop to improve tracking performance, it may not be the most suitable approach when a certain range of impedance parameters has to be rendered. In particular, it turns out that the viable range of stable stiffness and damping values can be strongly affected by the bandwidth of the inner control loops (e.g. a torque loop) as well as by the filtering and sampling frequency. This paper provides an extensive analysis on how these aspects influence the stability region of impedance parameters as well as the passivity of the system. This will be supported by both simulations and experimental data. Moreover, a methodology for designing joint impedance controllers based on an inner torque loop and a positive velocity feedback loop will be presented. The goal of the velocity feedback is to increase (given the constraints to preserve stability) the bandwidth of the torque loop without the need of a complex controller.Comment: 14 pages in Control Theory and Technology (2016

Fuzzy anti-windup scheme for practical control of point-to-point (Ptp) positioning systems

The Positioning Systems Generally Need A Controller To Achieve High Accuracy, Fast Response And Robustness. In Addition, Ease Of Controller Design And Simplicity Of Controller Structure Are Very Important For Practical Application. For Satisfying These Requirements, Nominal Characteristic Trajectory Following (NCTF) Controller Has Been Proposed As A Practical PTP Positioning Control. However, The Effect Of Actuator Saturation Cannot Be Completely Compensated Due To Integrator Windup Because Of Plant Parameter Variations. This Paper Presents A Method To Improve The NCTF Controller For Overcoming The Problem Of Integrator Windup By Adopting A Fuzzy Anti-Windup Scheme. The Improved NCTF Controller Is Evaluated Through Simulation Using Dynamic Model Of A Rotary Positioning System. The Results Show That The Improved NCTF Controller Is Adequate To Compensate The Effect Of Integrator Windup

Performance and manufacturing considerations for series elastic actuators

Robots are becoming an integral part of our lives. We are already physically connected with them through many robotic applications such as exoskeletons in military, orthosis devices in health care, collaborative robots in industry, etc. While the integration of robots improves the quality of human life, it still poses a safety concern during the physical human-robot interaction. Series Elastic Actuators (SEAs) play an important role in improving the safety of human-robot interaction and collaboration. Considering the fast expansion of robotic applications in our lives and the safety benefits of SEAs, it is conceivable that SEAs are going to play an important role in robotic applications in every aspect of human life. This dissertation focuses on reducing the cost, simplifying the use and improving the performance of SEAs. The first research focus in this dissertation is to reduce the cost of SEAs. Robots are successful in reducing production and service costs when used but the capital cost of robot installations are very high. As robotics research shifts to safe robotic applications, reducing the cost of SEAs will greatly help to deploy this technology in more robotic applications and to increase their accessibility to a broader range of researchers and educators. With this motivation, I present a case study on reducing the cost of a SEA while maintaining high force and position control performance and industrial grade service life. The second research focus in this dissertation is to simplify the laborious gain selection process of the cascaded controllers of SEAs. In order to simplify the gain selection process of the impedance controllers of SEAs, an optimal feedback gain selection methodology was developed. Using this method, the feedback gains of the cascaded PD-type impedance controllers of SEAs can easily be calibrated. The developed method allows the users to find the highest feedback gains for a desired phase-margin. Beyond the low-cost realization and simple controller tuning of SEAs, performance improvements on SEAs are possible utilizing the series elasticity in these actuators. As the third research focus in this dissertation, a sequential convex optimization-based motion planning technique is developed in order to improve the joint velocity capabilities of SEAs with nonlinearities. By using this method, higher joint velocities, that are not achievable with the rigid counterparts of SEAs can be achievedMechanical Engineerin

Dynamic modeling, property investigation, and adaptive controller design of serial robotic manipulators modeled with structural compliance

Research results on general serial robotic manipulators modeled with structural compliances are presented. Two compliant manipulator modeling approaches, distributed and lumped parameter models, are used in this study. System dynamic equations for both compliant models are derived by using the first and second order influence coefficients. Also, the properties of compliant manipulator system dynamics are investigated. One of the properties, which is defined as inaccessibility of vibratory modes, is shown to display a distinct character associated with compliant manipulators. This property indicates the impact of robot geometry on the control of structural oscillations. Example studies are provided to illustrate the physical interpretation of inaccessibility of vibratory modes. Two types of controllers are designed for compliant manipulators modeled by either lumped or distributed parameter techniques. In order to maintain the generality of the results, neither linearization is introduced. Example simulations are given to demonstrate the controller performance. The second type controller is also built for general serial robot arms and is adaptive in nature which can estimate uncertain payload parameters on-line and simultaneously maintain trajectory tracking properties. The relation between manipulator motion tracking capability and convergence of parameter estimation properties is discussed through example case studies. The effect of control input update delays on adaptive controller performance is also studied

Deformation Control in Rest-to-Rest Motion of Mechanisms with Flexible Links

This paper develops and validates experimentally a feedback strategy for the reduction of the link deformations in rest-to-rest motion of mechanisms with flexible links, named Delayed Reference Control (DRC). The technique takes advantage of the inertial coupling between rigid-bodymotion and elasticmotion to control the undesired link deformations by shifting in time the position reference through an action reference parameter. The action reference parameter is computed on the fly based on the sensed strains by solving analytically an optimization problem. An outer control loop is closed to compute the references for the position controllers of each actuator, which can be thought of as the inner control loop. The resulting multiloop architecture of the DRC is a relevant advantage over several traditional feedback controllers: DRC can be implemented by just adding an outer control loop to standard position controllers. A validation of the proposed control strategy is provided by applying the DRC to the real-time control of a four-bar linkage