Fast switching current detection at low critical currents

A pulse-and-hold technique is used to measure the switching of small critical current Josephson junctions. This technique allows one to achieve a good binary detection and therefore measure switching probabilities. The technique overcomes limitations on simple square pulses and allows for the measurement of junctions with critical currents of the order of 10nA with bias pulses of the order of 100ns. A correlation analysis of the switching events is performed to show how the switching probability depends on the wait time between repeated bias pulses.Comment: Changed abstract Added reference 1

Compensation of Distribution System Voltage using DVR

A dynamic voltage restorer (DVR) is a power-electronic controller that can protect sensitive loads from disturbances in the supply system. In this paper, it is demonstrated that this device can tightly regulate the voltage at the load terminal against imbalance or harmonic in the source side. The behavior of the device is studied through steady-state analysis, and limits to achievable performance are found. This analysis is extended to the study of transient operation where the generation of the reference voltage of the DVR is discussed. Once the reference signals are generated, they are tracked using a switching band scheme. A suitable structure in which the DVR is realized by voltage-source inverters (VSIs) is also discussed. Particular emphasis to the rating of this device is provided. Extensive simulation results are included to illustrate the operating principles of a DVR

Engineering evaluations and studies. Volume 2: Exhibit B, part 1

Ku-band communication system analysis, S-band system investigations, payload communication investigations, shuttle/TDRSS and GSTDN compatibility analysis are discussed

An Optically Stabilized Fast-Switching Light Emitting Diode as a Light Source for Functional Neuroimaging

Neuroscience research increasingly relies on optical methods for evoking neuronal activity as well as for measuring it, making bright and stable light sources critical building blocks of modern experimental setups. This paper presents a method to control the brightness of a high-power light emitting diode (LED) light source to an unprecedented level of stability. By continuously monitoring the actual light output of the LED with a photodiode and feeding the result back to the LED's driver by way of a proportional-integral controller, drift was reduced to as little as 0.007% per hour over a 12-h period, and short-term fluctuations to 0.005% root-mean-square over 10 seconds. The LED can be switched on and off completely within 100 µs, a feature that is crucial when visual stimuli and light for optical recording need to be interleaved to obtain artifact-free recordings. The utility of the system is demonstrated by recording visual responses in the central nervous system of the medicinal leech Hirudo verbana using voltage-sensitive dyes

Harmonic correction in power supplies feeding non-linear loads

This paper focuses on the design of an electronic circuit which can be used in conjunction with the power supplies used at the input of non-linear loads (computers, TV sets, etc.) in order to filter out the input current harmonics in such loads. The electronic circuit will fill the gaps of the distorted current waveform so that it becomes sinusoidal and also in phase with the mains supply. In this paper different configurations of the proposed electronic circuit are covered (depending on the location with respect to the non-linear load). An optimization algorithm is carried out in order to find the best location, minimum device rating for different type of loads. The proposed circuit monitors the input current, output voltage and power rating of the power supply. The circuit will then decide whether to filter the input current harmonics or the output voltage harmonics. The circuit will also optimize the best switching frequency for the required load so that the power supply operates at the maximum possible efficiency

The Essential Role and the Continuous Evolution of Modulation Techniques for Voltage-Source Inverters in the Past, Present, and Future Power Electronics

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future

Automated routing and control of silicon photonic switch fabrics

Automatic reconfiguration and feedback controlled routing is demonstrated in an 8×8 silicon photonic switch fabric based on Mach-Zehnder interferometers. The use of non-invasive Contactless Integrated Photonic Probes (CLIPPs) enables real-time monitoring of the state of each switching element individually. Local monitoring provides direct information on the routing path, allowing an easy sequential tuning and feedback controlled stabilization of the individual switching elements, thus making the switch fabric robust against thermal crosstalk, even in the absence of a cooling system for the silicon chip. Up to 24 CLIPPs are interrogated by a multichannel integrated ASIC wire-bonded to the photonic chip. Optical routing is demonstrated on simultaneous WDM input signals that are labelled directly on-chip by suitable pilot tones without affecting the quality of the signals. Neither preliminary circuit calibration nor lookup tables are required, being the proposed control scheme inherently insensible to channels power fluctuations

Fluidic Valves for Variable-Configuration Gas Treatment

The paper surveys recent development in the highly specialized field of chemical engineering: vehicle exhaust gas aftertreatment, where variable configuration systems are currently introduced or considered. These respond to varying operating conditions by inserting into the gas treatment flowpath different reactors. The main practical problem are the valves for gas flow switching. Usual mechanical valves are costly, failure prone, heavy (especially the solenoid variants), and not robust enough to withstand the adverse conditions of high temperature, vibration, shocks and dripping water and mud at the usual locations under vehicle body. Fluidic no-moving-part valves, inexpensive and robust, are proposed as an attractive alternative. Especially in their novel axisymmetric layout, they may be very compact, in fact integral with reactor body. The qualitative change brought by the new approaches may provide an inspiration to other areas of chemical engineering