Dynamic range and sensitivity improvement of infrared detectors using BiCMOS technology

The field of infrared (IR) detector technology has shown vast improvements in terms of speed and performance over the years. Specifically the dynamic range (DR) and sensitivity of detectors showed significant improvements. The most commonly used technique of implementing these IR detectors is the use of charge-coupled devices (CCD). Recent developments show that the newly investigated bipolar complementary metal-oxide semiconductor (BiCMOS) devices in the field of detector technology are capable of producing similar quality detectors at a fraction of the cost. Prototyping is usually performed on low-cost silicon wafers. The band gap energy of silicon is 1.17 eV, which is too large for an electron to be released when radiation is received in the IR band. This means that silicon is not a viable material for detection in the IR band. Germanium exhibits a band gap energy of 0.66 eV, which makes it a better material for IR detection. This research is aimed at improving DR and sensitivity in IR detectors. CCD technology has shown that it exhibits good DR and sensitivity in the IR band. CMOS technology exhibits a reduction in prototyping cost which, together with electronic design automation software, makes this an avenue for IR detector prototyping. The focus of this research is firstly on understanding the theory behind the functionality and performance of IR detectors. Secondly, associated with this, is determining whether the performance of IR detectors can be improved by using silicon germanium (SiGe) BiCMOS technology instead of the CCD technology most commonly used. The Simulation Program with Integrated Circuit Emphasis (SPICE) was used to realise the IR detector in software. Four detectors were designed and prototyped using the 0.35 µm SiGe BiCMOS technology from ams AG as part of the experimental verification of the formulated hypothesis. Two different pixel structures were used in the four detectors, which is the silicon-only p-i-n diodes commonly found in literature and diode-connected SiGe heterojunction bipolar transistors (HBTs). These two categories can be subdivided into two more categories, which are the single-pixel-single-amplifier detectors and the multiple-pixel-single-amplifier detector. These were needed to assess the noise performance of different topologies. Noise influences both the DR and sensitivity of the detector. The results show a unique shift of the detecting band typically seen for silicon detectors to the IR band, accomplished by using the doping feature of HBTs using germanium. The shift in detecting band is from a peak of 250 nm to 665 nm. The detector still accumulates radiation in the visible band, but a significant portion of the near-IR band is also detected. This can be attributed to the reduced band gap energy that silicon with doped germanium exhibits. This, however, is not the optimum structure for IR detection. Future work that can be done based on this work is that the pixel structure can be optimised to move the detecting band even more into the IR region, and not just partially.Dissertation (MEng)--University of Pretoria, 2013.Electrical, Electronic and Computer Engineeringunrestricte

Realization of a low noise amplifier using 0.35 um SiGe-BicMOS Technology for IEEE 802.11a applications /

The trend demand for towards interactive multimedia services has forced the development of new wireless systems that has greater bandwidths. The evolution of current wireless communication systems has been very rapid. The main goal has been small-size and low-cost transceivers that can be designed for different applications. Data communication systems in compliant with IEEE 802.11a wireless local area network (WLAN) standard has found widespread use, meeting the market demands, for the last few years. Next generation WLAN operates in the 5-6 GHz frequency range. A front-end receiver capable of operating within this frequency range is essential to meet the current and future of products. One of the critical components, allowing the common use of the technology can be attributed to the high performance Low Noise Amplifiers (LNA) in the receiver chain of the 802.11a transceivers. In IEEE 802.11a, there are three frequency bands; 5.15GHz - 5.25GHz, 5.25GHz - 5.35GHz and 5.725GHz - 5.825GHz. In this thesis, we designed and fabricated a single-stage cascode amplifier with emitter inductive degeneration using 0.35 ´m-SiGe BiCMOS process for IEEE 802.11a receivers. The electromagnetic (EM) simulations of the passive components are performed by using Agilent MOMENTUM® tool and all the parasitic components are extracted and compensated, a crucial step for optimizing the performance parameters of the LNA. The simulation results are very similar to measurement results, confirming the effectiveness of design methodology provided in this work

SiGe BiCMOS front-end circuits for X-Band phased arrays

The current Transmit/Receive (T/R) modules have typically been implemented using GaAs- and InP-based discrete monolithic microwave integrated circuits (MMIC) to meet the high performance requirement of the present X-Band phased arrays. However their cost, size, weight, power consumption and complexity restrict phased array technology only to certain military and satellite applications which can tolerate these limitations. Therefore, next generation X-Band phased array radar systems aim to use low cost, silicon-based fully integrated T/R modules. For this purpose, this thesis explores the design of T/R module front-end building blocks based on new approaches and techniques which can pave the way for implementation of fully integrated X-Band phased arrays in low-cost SiGe BiCMOS process. The design of a series-shunt CMOS T/R switch with the highest IP1dB, compared to other reported works in the literature is presented. The design focuses on the techniques, primarily, to achieve higher power handling capability (IP1dB), along with higher isolation and better insertion loss of the T/R switch. Also, a new T/R switch was implemented using shunt NMOS transistors and slow-wave quarter wavelength transmission lines. It presents the utilization of slow-wave transmissions lines in T/R switches for the first time in any BiCMOS technology to the date. A fully integrated DC to 20 GHz SPDT switch based on series-shunt topology was demonstrated. The resistive body oating and on-chip impedance transformation networks (ITN) were used to improve power handling of the switch. An X-Band high performance low noise ampli er (LNA) was implemented in 0.25 μm SiGe BiCMOS process. The LNA consists of inductively degenerated two cascode stages with high speed SiGe HBT devices to achieve low noise gure (NF), high gain and good matching at the input and output, simultaneously. The performance parameters of the LNA collectively constitute the best Figure-of-Merit value reported in similar technologies, to the best of author's knowledge. Furthermore, a switched LNA was implemented SiGe BiCMOS process for the first time at X-Band. The resistive body floating technique was incorporated in switched LNA design, for the first time, to improve the linearity of the circuit further in bypass mode. Finally, a complete T/R module with a state-of-the-art performance was implemented using the individually designed blocks. The simulations results of the T/R module is presented in the dissertation. The state-of-the-art performances of the presented building blocks and the complete module are attributed to the unique design methodologies and techniques

Phase noise reduction of a 0.35 μm BiCMOS SiGe 5 GHz Voltage Controlled Oscillator

The research conducted in this dissertation studies the issues regarding the improvement of phase noise performance in a BiCMOS Silicon Germanium (SiGe) cross-coupled differential-pair voltage controlled oscillator (VCO) in a narrowband application as a result of a tail-current shaping technique. With this technique, low-frequency noise components are reduced by increasing the signal amplitude without consuming additional power, and its effect on overall phase noise performance is evaluated. The research investigates effects of the tail-current as a main contributor to phase noise, and also other effects that may influence the phase noise performance like inductor geometry and placement, transistor sizing, and the gain of the oscillator. The hypothesis is verified through design in a standard 0.35 μm BiCMOS process supplied by Austriamicrosystems (AMS). Several VCOs are fabricated on-chip to serve for a comparison and verify that the employment of tail-current shaping does improve phase noise performance. The results are then compared with mathematical models and simulated results, to confirm the hypothesis. Simulation results provided a 3.3 dBc/Hz improvement from -105.3 dBc/Hz to -108.6 dBc/Hz at a 1 MHz offset frequency from the 5 GHz carrier when employing tail-current shaping. The relatively small increase in VCO phase noise performance translates in higher modulation accuracy when used in a transceiver, therefore this increase can be regarded as significant. Parametric analysis provided an additional 1.8 dBc/Hz performance enhancement in phase noise that can be investigated in future works. The power consumption of the simulated VCO is around 6 mW and 4.1 mW for the measured prototype. The circuitry occupies 2.1 mm2 of die area. CopyrightDissertation (MEng)--University of Pretoria, 2010.Electrical, Electronic and Computer Engineeringunrestricte

Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

Silicon Germanium BiCMOS Comparator Designed for Use in An Extreme Environment Analog to Digital Converter

This thesis demonstrates the process of creating a radiation hardened and extreme temperature operating comparator from start to finish in the 90 nm SiGe 9HP process node. This includes the entire design flow from examining comparator topologies, to designing the initial comparator circuits, to simulating the comparator over a temperature range of -196°C to 125°C, and finally the testing of the fabricated circuit. To verify the circuit would work at low temperatures, several new device models were created that could be used for simulations at -196°C. In addition to its properties as a standalone comparator, the circuit was also used as a building block in a SAR ADC that would be used for extreme environments

SiGe BiCMOS ICs for X-Band 7-Bit T/R module with high precision amplitude and phase control

Over the last few decades, phased array radar systems had been utilizing Transmit/Receive (T/R) modules implemented in III-V semiconductor based technologies. However, their high cost, size, weight and low integration capability created a demand for seeking alternative solutions to realize T/R modules. In recent years, SiGe BiCMOS technologies are rapidly growing their popularity in T/R module applications by virtue of meeting high performance requirements with more reduced cost and power dissipation with respect to III-V technologies. The next generation phased array radar systems require a great number of fully integrated, high yield, small-scale and high accuracy T/R modules. In line with these trends, this thesis presents the design and implementation of the first and only 7-Bit X-Band T/R module with high precision amplitude and phase control in the open literature, which is realized in IHP 0.25μ SiGe BiCMOS technology. In the scope of this thesis, sub-blocks of the designed T/R module such as low noise amplifier (LNA), inter-stage amplifier, SiGe Hetero-Junction Bipolar Transistor (HBT) Single- Pole Double-Throw (SPDT) switch and 7-Bit digitally controlled step attenuator are extensively discussed. The designed LNA exhibits Noise Figure (NF) of 1.7 dB, gain of 23 dB, Output Referred Compression Point (OP1dB) of 16 dBm while the inter-stage amplifier gives measured NF of 3 dB, gain of 15 dB and OP1dB of 18 dBm. Moreover, the designed SPDT switch has an Insertion Loss (IL) of 1.7 dB, isolation of 40 dB and OP1dB of 28 dBm. Lastly, the designed 7-Bit SiGe HBT digitally controlled step attenuator demonstrates IL of 8 dB, RMS attenuation error of 0.18 dB, RMS phase error of 2° and OP1dB of 16 dBm. The 7-Bit T/R module is constructed by using the sub-blocks given above, along with a 7- Bit phase shifter (PS) and a power amplifier (PA). Post-layout simulation results show that the designed T/R module exhibits a gain of 38 dB, RMS phase error of 2.6°, RMS amplitude error of 0.82 dB and Rx-Tx isolation of 80 dB across X-Band. The layout of T/R module occupies an area of 11.37 mm2