Formation of porous membranes for drug delivery systems

Highly crystalline porous hollow poly (-lactide) (PLLA) fibres suitable for the delivery of various drugs were obtained using a dry-wet spinning process. The pore structure of the fibres could be regulated by changing the spinning systems and spinning conditions. Using the spinning system PLLA-dioxane-water, fibres with a dense toplayer and a spongy sublayer were obtained. The spinning system PLLA-chloroform/toluene-methanol yielded fibres with a very open porous structure. The membrane formation of the former system probably occurs by liquid-liquid demixing followed by crystallization of the polymer rich phase. In the membrane formation process of the spinning system, PLLA-chloroform/toluene-methanol crystallization probably plays a dominant role. The membrane formation process will be related to basic principles of phase separation. The fibres are suitable for the long term zero order delivery of the contraceptive 3-ketodesogestrel and the short term zero order delivery of the cytostatic agent, cisplatin. The drugs are released by dissolution of the drug crystals in the fibre core followed by diffusion through the membrane structure. Short term release of adriamycin could be obtained through an adsorption-desorption mechanism. The pore structures of the fibres have a large influence on the release rates of the drugs investigated. When fibres with dense toplayers were used, low release rates of drugs were observed whereas fibres with well interconnected pore structures over the fibre wall showed very high release rates

A technique for the measurement of reinforcement fibre tensile strength at sub-millimetre gauge lengths

The strength of composite reinforcement fibres is normally measured on samples of much greater length than the actual residual fibre lengths found in many composite materials. This is due to a number of limitations of the standard techniques which are employed. We present a description of a technique which enables values for the tensile strength of composite reinforcement fibres at short gauge lengths to be obtained. The technique is based on an adaptation of a micro-mechanical test apparatus for fibre pullout measurements. Data is presented which was obtained at gauge lengths of 180-380 µm on E-glass and S-2 glass® fibres taken from different chopped reinforcement products. The technique can be used at gauge lengths as short as 20 µm. The data indicates that the values of average fibre strength in these products are significantly below the pristine glass strength values

The compounding of short fibre reinforced thermoplastic composites

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.It is generally accepted that the mechanical properties of short fibre reinforced thermoplastics do not correspond with the high mechanical properties of fibres used to reinforce them. A study is made into the methods of compounding reinforcing fibres into thermoplastics to produce short fibre reinforced thermoplastics of enhanced properties. The initial method chosen for investigation is the twin screw extrusion compounding process. Variables such as fibre feeding arrangement and extrusion screw design are found to be factors influencing the properties of carbon and glass reinforced nylon 6,6. Use is made of computer programs to predict properties, assess compound quality and estimate fibre-matrix bond strength. Investigations indicate that the presence of reinforcing fibres with enhanced lengths does not result in the predicted property increases. The reasons for this shortfall are believed to lie in unfavourable fibre orientation in injection mouldings and the reduced strain to break of these materials. Short Kevlar reinforced thermoplastics are compounded and their mechanical properties assessed. The reasons for the poor mechanical properties for these materials are identified as a poor bond strength between fibre and matrix, the formation of points of weakness within the fibres by the compounding and moulding processes and the coiled arrangement of fibres present in injection mouldings. A method suitable for the routine assessment of fibre-matrix bond strength is used to examine combinations of fibre and thermoplastic matrix. A comparison is made of the values derived from this method with values calculated from stress-strain curves of injection mouldings. This allows an understanding of the nature of the fibre-matrix bond yielded by compounding and injection moulding steps. A description is given of a novel method designed to overcome the limitations of conventional compounding routes to produce long fibre reinforced injection moulding feedstock. Further work is necessary before this method is a feasible production technique

Sodium channel inactivation kinetics of rat sensory and motor nerve fibres and their modulation by glutathione

Na+ channel currents of rat motor and sensory nerve fibres were studied with the patch-clamp technique on enzymatically demyelinated axons. Differences between motor and sensory fibres in multi-channel inactivation kinetics and the gating of late single-channel currents were investigated. In the axon-attached mode, inactivation of multi-channel Na+ currents in sensory axons was best fitted with a single time constant while for motor axons two time constants were needed. Late single-channel currents in sensory axons were characterized by short openings whereas motor axons exhibited additional long single-channel openings. In contrast, in excised, inside-out membrane patches, no differences between motor and sensory fibres were found: in both types of fibre inactivation of multi-channel Na+ currents proceeded with two time constants and late single-channel currents showed short and long openings. After application of the reducing agent glutathione to the cytoplasmic side of excised inside-out patches, inactivation of Na+ currents in both motor and sensory fibres proceeded with a single, fast exponential time constant and late currents appeared with short openings only. These data indicate that the axonal metabolism may contribute to the different inactivation kinetics of Na+ currents in motor and sensory nerve fibres

Nanocellulose as building block for novel materials

This thesis describes the fabrication of novel green materials using nanocellulose as the building block. Bacterial cellulose (BC) was used as the nanocellulose predominantly in this work. BC is highly crystalline pure cellulose with an inherent fibre diameter in the nano-scale. A single BC nanofibre was found to possess a Young’s modulus of 114 GPa. All these properties are highly favourable for using BC as a nanofiller/reinforcement in green nanocomposite materials. In this work, the surface of BC was rendered hydrophobic by grafting organic acids with various aliphatic chain lengths. These surface-modified BC was used as nanofiller for poly(L-lactide) (PLLA). Direct wetting measurements showed that the BC nanofibre-PLLA interface was improved due to the hydrophobisation of BC with organic acids. This led to the production of BC reinforced PLLA nanocomposites with improved tensile properties. Nanocellulose can also be obtained by grinding of wood pulp, producing nanofibrillated cellulose (NFC). The surface and bulk properties of one type of NFC and BC were compared in this work. Furthermore, the reinforcing ability of NFC and BC was also studied and it was observed that there is no significant difference in the mechanical performance of NFC or BC reinforced nanocomposites. A novel method based on slurry dipping to coat sisal fibres with BC was developed to modify the surface of natural fibres. This method can produce either (i) a densely BC coating layer or (ii) “hairy” BC coated sisal fibres. Randomly oriented short BC coated sisal fibre reinforced hierarchical composites were manufactured. It was found that hierarchical (nano)composites containing BC coated sisal fibres and BC dispersed in the matrix were required to produce composites with improved mechanical properties. This slurry dipping method was also extended to produce robust short sisal fibre preforms. By infusing this preform with a bio-based thermosetting resin followed by curing, green composites with significantly improved mechanical properties were produced. BC was also used as stabiliser and nano-filler for the production of macroporous polymers made by frothing of acrylated epoxidised soybean oil followed by microwave curing

Unidirectional Rotation Neurones in the Optomotor System of the Crab, Carcinus

1. Among the optomotor fibres to the eye muscles in Carcinus a class was found which responds to unidirectional fast rotations around various body axes. All had large signals and are therefore of large diameter. 2. In one set of these fibres which fires especially for rotations around the dorsoventral axis, it could be shown that discharges take place especially during accelerations and that, when a rotation in the null direction is suddenly stopped, a short discharge occurs. The fibres for other axes behave in a similar manner. 3. For rotations around the ventro-dorsal axis, but not for other directions, mediumsized fibres are present which, in contrast to the fast fibres, respond to visual stimulation, as well as to body rotations in darkness, thus combining the input properties of the unidirectional fast rotatory and the unidirectional purely optokinetic small fibres. Their sensitivity to visual input is for low rotation velocities, to body rotations is for high rotation velocities

Regenerating the strength of thermally recycled glass fibres using hot sodium hydroxide

Results are presented from the ReCoVeR project on the regeneration of the strength of thermally conditioned glass fibres. Thermal recycling of end-of-life glass fibre reinforced composites or composite manufacturing waste delivers fibres with virtually no residual strength or value. Composites produced from such fibres also have extremely poor mechanical performance. Data is presented showing that a short hot sodium hydroxide solution treatment of such recycled fibres can more than triple their strength and restore their ability to act as an effective reinforcement in second life composite materials. The implications of these results for real materials reuse of recycled glass fibres as replacement for pristine reinforcement fibres are discussed

Lightweight metallic matrix composites. Development of new composites material reinforced with carbon structures

Carbon nano/micro-structures used as fillers in metallic lightweight alloys matrix composites are receiving considerable attention in scientific research and industrial applications. Aluminum and magnesium are the most studied light metals used as matrices in metal composites materials principally for their low density (respectively 2.7 g/cm3 and 1.7 g/cm3) and low melting temperature (around 660 °C for both metals). A good interaction between matrix and fillers is the first step to obtain an increase in bulk properties; furthermore, the manufacturing procedure of the composite is fundamental in terms of quality of fillers dispersion. In this work the influence of surface modifications for three classes of carbon fillers for aluminum and magnesium alloy (AZ63) as matrices is studied. In particular, the selected fillers are short carbon micro fibres (SCMFs), carbon woven fabrics (CWF) and unidirectional yarn carbon fibres (UYFs). The surface modification was carried out by a direct coating of pure nickel on fibres. The electroless pure nickel plating was chosen as coating technique and the use of hydrazine as reducing agent has prevented the co-deposition of other elements (such as P or B). SEM and EDS analyses were performed to study the effect of surface modifications. The mechanical properties of manufactured composites were evaluated by four point flexural tests according to ASTM C1161 (room temperature). Results confirm improved interactions between matrix and fillers, and the specific interaction was studied for any chosen reinforcement