Fast, non-monte-carlo estimation of transient performance variation due to device mismatch

This paper describes an efficient way of simulating the effects of device random mismatch on circuit transient characteristics, such as variations in delay or in frequency. The proposed method models DC random offsets as equivalent AC pseudo-noises and leverages the fast, linear periodically time-varying (LPTV) noise analysis available from RF circuit simulators. Therefore, the method can be considered as an extension to DC match analysis and offers a large speed-up compared to the traditional Monte-Carlo analysis. Although the assumed linear perturbation model is valid only for small variations, it enables easy ways to estimate correlations among variations and identify the most sensitive design parameters to mismatch, all at no additional simulation cost. Three benchmarks measuring the variations in the input offset voltage of a clocked comparator, the delay of a logic path, and the frequency of an oscillator demonstrate the speed improvement of about 100-1000x compared to a 1000-point Monte-Carlo method

Discovering an active subspace in a single-diode solar cell model

Predictions from science and engineering models depend on the values of the model's input parameters. As the number of parameters increases, algorithmic parameter studies like optimization or uncertainty quantification require many more model evaluations. One way to combat this curse of dimensionality is to seek an alternative parameterization with fewer variables that produces comparable predictions. The active subspace is a low-dimensional linear subspace defined by important directions in the model's input space; input perturbations along these directions change the model's prediction more, on average, than perturbations orthogonal to the important directions. We describe a method for checking if a model admits an exploitable active subspace, and we apply this method to a single-diode solar cell model with five input parameters. We find that the maximum power of the solar cell has a dominant one-dimensional active subspace, which enables us to perform thorough parameter studies in one dimension instead of five

Robust and Efficient Uncertainty Quantification and Validation of RFIC Isolation

Modern communication and identification products impose demanding constraints on reliability of components. Due to this statistical constraints more and more enter optimization formulations of electronic products. Yield constraints often require efficient sampling techniques to obtain uncertainty quantification also at the tails of the distributions. These sampling techniques should outperform standard Monte Carlo techniques, since these latter ones are normally not efficient enough to deal with tail probabilities. One such a technique, Importance Sampling, has successfully been applied to optimize Static Random Access Memories (SRAMs) while guaranteeing very small failure probabilities, even going beyond 6-sigma variations of parameters involved. Apart from this, emerging uncertainty quantifications techniques offer expansions of the solution that serve as a response surface facility when doing statistics and optimization. To efficiently derive the coefficients in the expansions one either has to solve a large number of problems or a huge combined problem. Here parameterized Model Order Reduction (MOR) techniques can be used to reduce the work load. To also reduce the amount of parameters we identify those that only affect the variance in a minor way. These parameters can simply be set to a fixed value. The remaining parameters can be viewed as dominant. Preservation of the variation also allows to make statements about the approximation accuracy obtained by the parameter-reduced problem. This is illustrated on an RLC circuit. Additionally, the MOR technique used should not affect the variance significantly. Finally we consider a methodology for reliable RFIC isolation using floor-plan modeling and isolation grounding. Simulations show good comparison with measurements

Bond graph based sensitivity and uncertainty analysis modelling for micro-scale multiphysics robust engineering design

Components within micro-scale engineering systems are often at the limits of commercial miniaturization and this can cause unexpected behavior and variation in performance. As such, modelling and analysis of system robustness plays an important role in product development. Here schematic bond graphs are used as a front end in a sensitivity analysis based strategy for modelling robustness in multiphysics micro-scale engineering systems. As an example, the analysis is applied to a behind-the-ear (BTE) hearing aid. By using bond graphs to model power flow through components within different physical domains of the hearing aid, a set of differential equations to describe the system dynamics is collated. Based on these equations, sensitivity analysis calculations are used to approximately model the nature and the sources of output uncertainty during system operation. These calculations represent a robustness evaluation of the current hearing aid design and offer a means of identifying potential for improved designs of multiphysics systems by way of key parameter identification

Global sensitivity analysis of the single particle lithium-ion battery model with electrolyte

The importance of global sensitivity analysis (GSA) has been well established in many scientific areas. However, despite its critical role in evaluating a model’s plausibility and relevance, most lithium ion battery models are published without any sensitivity analysis. In order to improve the lifetime performance of battery packs, researchers are investigating the application of physics based electrochemical models, such as the single particle model with electrolyte (SPMe). This is a challenging research area from both the parameter estimation and modelling perspective. One key challenge is the number of unknown parameters: the SPMe contains 31 parameters, many of which are themselves non-linear functions of other parameters. As such, relatively few authors have tackled this parameter estimation problem. This is exacerbated because there are no GSAs of the SPMe which have been published previously. This article addresses this gap in the literature and identifies the most sensitive parameter, preventing time being wasted on refining parameters which the output is insensitive to

Mixed-signal CNN array chips for image processing

Due to their local connectivity and wide functional capabilities, cellular nonlinear networks (CNN) are excellent candidates for the implementation of image processing algorithms using VLSI analog parallel arrays. However, the design of general purpose, programmable CNN chips with dimensions required for practical applications raises many challenging problems to analog designers. This is basically due to the fact that large silicon area means large development cost, large spatial deviations of design parameters and low production yield. CNN designers must face different issues to keep reasonable enough accuracy level and production yield together with reasonably low development cost in their design of large CNN chips. This paper outlines some of these major issues and their solutions

Significance Driven Hybrid 8T-6T SRAM for Energy-Efficient Synaptic Storage in Artificial Neural Networks

Multilayered artificial neural networks (ANN) have found widespread utility in classification and recognition applications. The scale and complexity of such networks together with the inadequacies of general purpose computing platforms have led to a significant interest in the development of efficient hardware implementations. In this work, we focus on designing energy efficient on-chip storage for the synaptic weights. In order to minimize the power consumption of typical digital CMOS implementations of such large-scale networks, the digital neurons could be operated reliably at scaled voltages by reducing the clock frequency. On the contrary, the on-chip synaptic storage designed using a conventional 6T SRAM is susceptible to bitcell failures at reduced voltages. However, the intrinsic error resiliency of NNs to small synaptic weight perturbations enables us to scale the operating voltage of the 6TSRAM. Our analysis on a widely used digit recognition dataset indicates that the voltage can be scaled by 200mV from the nominal operating voltage (950mV) for practically no loss (less than 0.5%) in accuracy (22nm predictive technology). Scaling beyond that causes substantial performance degradation owing to increased probability of failures in the MSBs of the synaptic weights. We, therefore propose a significance driven hybrid 8T-6T SRAM, wherein the sensitive MSBs are stored in 8T bitcells that are robust at scaled voltages due to decoupled read and write paths. In an effort to further minimize the area penalty, we present a synaptic-sensitivity driven hybrid memory architecture consisting of multiple 8T-6T SRAM banks. Our circuit to system-level simulation framework shows that the proposed synaptic-sensitivity driven architecture provides a 30.91% reduction in the memory access power with a 10.41% area overhead, for less than 1% loss in the classification accuracy.Comment: Accepted in Design, Automation and Test in Europe 2016 conference (DATE-2016

Surrogate based Optimization and Verification of Analog and Mixed Signal Circuits

Nonlinear Analog and Mixed Signal (AMS) circuits are very complex and expensive to design and verify. Deeper technology scaling has made these designs susceptible to noise and process variations which presents a growing concern due to the degradation in the circuit performances and risks of design failures. In fact, due to process parameters, AMS circuits like phase locked loops may present chaotic behavior that can be confused with noisy behavior. To design and verify circuits, current industrial designs rely heavily on simulation based verification and knowledge based optimization techniques. However, such techniques lack mathematical rigor necessary to catch up with the growing design constraints besides being computationally intractable. Given all aforementioned barriers, new techniques are needed to ensure that circuits are robust and optimized despite process variations and possible chaotic behavior. In this thesis, we develop a methodology for optimization and verification of AMS circuits advancing three frontiers in the variability-aware design flow. The first frontier is a robust circuit sizing methodology wherein a multi-level circuit optimization approach is proposed. The optimization is conducted in two phases. First, a global sizing phase powered by a regional sensitivity analysis to quickly scout the feasible design space that reduces the optimization search. Second, nominal sizing step based on space mapping of two AMS circuits models at different levels of abstraction is developed for the sake of breaking the re-design loop without performance penalties. The second frontier concerns a dynamics verification scheme of the circuit behavior (i.e., study the chaotic vs. stochastic circuit behavior). It is based on a surrogate generation approach and a statistical proof by contradiction technique using Gaussian Kernel measure in the state space domain. The last frontier focus on quantitative verification approaches to predict parametric yield for both a single and multiple circuit performance constraints. The single performance approach is based on a combination of geometrical intertwined reachability analysis and a non-parametric statistical verification scheme. On the other hand, the multiple performances approach involves process parameter reduction, state space based pattern matching, and multiple hypothesis testing procedures. The performance of the proposed methodology is demonstrated on several benchmark analog and mixed signal circuits. The optimization approach greatly improves computational efficiency while locating a comparable/better design point than other approaches. Moreover, great improvements were achieved using our verification methods with many orders of speedup compared to existing techniques