Physical design methodologies for monolithic 3D ICs

The objective of this research is to develop physical design methodologies for monolithic 3D ICs and use them to evaluate the improvements in the power-performance envelope offered over 2D ICs. In addition, design-for-test (DfT) techniques essential for the adoption of shorter term through-silicon-via (TSV) based 3D ICs are explored. Testing of TSV-based 3D ICs is one of the last challenges facing their commercialization. First, a pre-bond testable 3D scan chain construction technique is developed. Next, a transition-delay-fault test architecture is presented, along with a study on how to mitigate IR-drop. Finally, to facilitate partitioning, a quick and accurate framework for test-TSV estimation is developed. Block-level monolithic 3D ICs will be the first to emerge, as significant IP can be reused. However, no physical design flows exist, and hence a monolithic 3D floorplanning framework is developed. Next, inter-tier performance differences that arise due to the not yet mature fabrication process are investigated and modeled. Finally, an inter-tier performance-difference aware floorplanner is presented, and it is demonstrated that high quality 3D floorplans are achievable even under these inter-tier differences. Monolithic 3D offers sufficient integration density to place individual gates in three dimensions and connect them together. However, no tools or techniques exist that can take advantage of the high integration density offered. Therefore, a gate-level framework that leverages existing 2D ICs tools is presented. This framework also provides congestion modeling and produces results that minimize routing congestion. Next, this framework is extended to commercial 2D IC tools, so that steps such as timing optimization and clock tree synthesis can be applied. Finally, a voltage-drop-aware partitioning technique is presented that can alleviate IR-drop issues, without any impact on the performance or maximum operating temperature of the chip.Ph.D

Extending systems-on-chip to the third dimension : performance, cost and technological tradeoffs.

Because of the today's market demand for high-performance, high-density portable hand-held applications, electronic system design technology has shifted the focus from 2-D planar SoC single-chip solutions to different alternative options as tiled silicon and single-level embedded modules as well as 3-D integration. Among the various choices, finding an optimal solution for system implementation dealt usually with cost, performance and other technological trade-off analysis at the system conceptual level. It has been identified that the decisions made within the first 20% of the total design cycle time will ultimately result up to 80% of the final product cost. In this paper, we discuss appropriate and realistic metric for performance and cost trade-off analysis both at system conceptual level (up-front in the design phase) and at implementation phase for verification in the three-dimensional integration. In order to validate the methodology, two ubiquitous electronic systems are analyzed under various implementation schemes and discuss the pros and cons of each of them

CELONCEL: Effective Design Technique for 3-D Monolithic Integration targeting High Performance Integrated Circuits

3-D monolithic integration (3DMI), also termed as sequential integration, is a potential technology for future gigascale circuits. Since the device layers are processed in sequential order, the size of the vertical contacts is similar to traditional contacts unlike in the case of parallel 3-D integration with through silicon vias (TSVs). Given the advantage of such small contacts, 3DMI enables manufacturing multiple active layers very close to each other. In this work we propose two different strategies of stacking standard cells in 3-D without breaking the regularity of the conventional design flow: a) Vertical stacking of diffusion areas (Intra-Cell stacking) that supports complete reuse of 2-D physical design tools and b) vertical stacking of cells over others (Cell-on-Cell stacking). A placement tool (CELONCEL-placer) targeting the Cell-on-Cell placement problem is proposed to allow high quality 3-D layout generation. Our experiments demonstrate the effectiveness of CELONCEL technique, fetching us an area gain of 37.5%, 15.51% reduction in wirelength, and 13.49% improvement in overall delay, compared with a 2-D case when benchmarked across an interconnect dominated low-densityparity-check (LDPC) decoder at 45nm technology node

Signaling in 3-D integrated circuits, benefits and challenges

Three-dimensional (3-D) or vertical integration is a design and packaging paradigm that can mitigate many of the increasing challenges related to the design of modern integrated systems. 3-D circuits have recently been at the spotlight, since these circuits provide a potent approach to enhance the performance and integrate diverse functions within amulti-plane stack. Clock networks consume a great portion of the power dissipated in a circuit. Therefore, designing a low-power clock network in synchronous circuits is an important task. This requirement is stricter for 3-D circuits due to the increased power densities. Synchronization issues can be more challenging for 3-D circuits since a clock path can spread across several planes with different physical and electrical characteristics. Consequently, designing low power clock networks for 3-D circuits is an important issue. Resonant clock networks are considered efficient low-power alternatives to conventional clock distribution schemes. These networks utilize additional inductive circuits to reduce power while delivering a full swing clock signal to the sink nodes. In this research, a design method to apply resonant clocking to synthesized clock trees is proposed. Manufacturing processes for 3-D circuits include some additional steps as compared to standard CMOS processes which makes 3-D circuits more susceptible to manufacturing defects and lowers the overall yield of the bonded 3-D stack. Testing is another complicated task for 3-D ICs, where pre-bond test is a prerequisite. Pre-bond testability, in turn, presents new challenges to 3-D clock network design primarily due to the incomplete clock distribution networks prior to the bonding of the planes. A design methodology of resonant 3-D clock networks that support wireless pre-bond testing is introduced. To efficiently address this issue, inductive links are exploited to wirelessly transmit the clock signal to the disjoint resonant clock networks. The inductors comprising the LC tanks are used as the receiver circuit for the links, essentially eliminating the need for additional circuits and/or interconnect resources during pre-bond test. Recent FPGAs are quite complex circuits which provide reconfigurablity at the cost of lower performance and higher power consumption as compared to ASIC circuits. Exploiting a large number of programmable switches, routing structures are mainly responsible for performance degradation in FPAGs. Employing 3-D technology can providemore efficient switches which drastically improve the performance and reduce the power consumption of the FPGA. RRAM switches are one of the most promising candidates to improve the FPGA routing architecture thanks to their low on-resistance and non-volatility. Along with the configurable switches, buffers are the other important element of the FPGAs routing structure. Different characteristics of RRAM switches change the properties of signal paths in RRAM-based FPGAs. The on resistance of RRAMswitches is considerably lower than CMOS pass gate switches which results in lower RC delay for RRAM-based routing paths. This different nature in critical path and signal delay in turn affect the need for intermediate buffers. Thus the buffer allocation should be reconsidered. In the last part of this research, the effect of intermediate buffers on signal propagation delay is studied and a modified buffer allocation scheme for RRAM-based FPGA routing path is proposed

Optimal Power Delivery Strategy in Modern VLSI Design

Department of Electrical EngineeringIn a modern very-large-scale integration (VLSI) designs, heterogeneous architectural structures and various three-dimensional (3D) integration methods have been used in a hybrid manner. Recently, the industry has combined 3D VLSI technology with the heterogeneous technology of modern VLSI called chiplet. The 3D heterogeneous architectural structure is growing attention because it reduces costs and time-to-market by increasing manufacturing yield with high integration rate and modularization. However, a main design concern of heterogeneous 3D architectural structure is power management for lowering power consumption with maintaining the required power integrity from IR drop. Although the low-power design can be realized in front-end-of-line level by reduced power supply complementary metal???oxide???semiconductor technologies, the overall low-power system performance is available with a proper design of power delivery network (PDN) for chip-level modules and system-level architectural structure. Thus, there is a demand for both the coanalysis and optimization for both chip-level and system-level. We analyzed and optimized power delivery on-chip in various 3D integration environments, and we also have proposed a chip-package-PCB coanalysis methodology at the system level. For through-silicon-via (TSV)-based 3D integration circuit (IC), We have investigated and analyzed the voltage noise in a multi-layer 3D stacking with partial element equivalent circuit (PEEC)-based on-chip PDN and frequency-dependent TSV models. We also have proposed a wire-added multi-paired on-chip PDN structure to reduce voltage noise to reduce IR drop. The performance of TSV-based 3D ICs has also been improved by reducing wake-up time through our proposed adaptive power gating strategy with tapered TSVs. For die-to-wafer 3D IC, we have proposed a power delivery pathfinding methodology, which seeks to identify a nearly optimal PDN for a given design and PDN specification. Our pathfinding methodology exploits models for routability and worst IR drop, which helps reducing iterations between PDN design and circuit design in 3D IC implementation. We also have extended the observation to system-level, we have proposed a power integrity coanalysis methodology for multiple power domains in high-frequency memory systems. Our coanalysis methodology can analyze the tendencies in power integrity by using parametric methods with consideration of package-on-package integration. We have proved that our methodology can predict similar peak-to-peak ripple voltages that are comparable with the realistic simulations of high-speed low-power memory interfaces. Finally, we have proposed analysis and optimization methodologies that are generally applicable to various integration methods used in modern VLSI designs as computer-aided-design-based solutions.clos

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

Méthodologies de conception ASIC pour des systèmes sur puce 3D hétérogènes à base de réseaux sur puce 3D

Dans cette thèse, nous étudions les architectures 3D NoC grâce à des implémentations de conception physiques en utilisant la technologie 3D réel mis en oeuvre dans l'industrie. Sur la base des listes d'interconnexions en déroute, nous procédons à l'analyse des performances d'évaluer le bénéfice de l'architecture 3D par rapport à sa mise en oeuvre 2D. Sur la base du flot de conception 3D proposé en se concentrant sur la vérification temporelle tirant parti de l'avantage du retard négligeable de la structure de microbilles pour les connexions verticales, nous avons mené techniques de partitionnement de NoC 3D basé sur l'architecture MPSoC y compris empilement homogène et hétérogène en utilisant Tezzaron 3D IC technlogy. Conception et mise en oeuvre de compromis dans les deux méthodes de partitionnement est étudiée pour avoir un meilleur aperçu sur l'architecture 3D de sorte qu'il peut être exploitée pour des performances optimales. En utilisant l'approche 3D homogène empilage, NoC topologies est explorée afin d'identifier la meilleure topologie entre la topologie 2D et 3D pour la mise en œuvre MPSoC 3D sous l'hypothèse que les chemins critiques est fondée sur les liens inter-routeur. Les explorations architecturales ont également examiné les différentes technologies de traitement. mettant en évidence l'effet de la technologie des procédés à la performance d'architecture 3D en particulier pour l'interconnexion dominant du design. En outre, nous avons effectué hétérogène 3D d'empilage pour la mise en oeuvre MPSoC avec l'approche GALS de style et présenté plusieurs analyses de conception physiques connexes concernant la conception 3D et la mise en œuvre MPSoC utilisant des outils de CAO 2D. Une analyse plus approfondie de l'effet microbilles pas à la performance de l'architecture 3D à l'aide face-à-face d'empilement est également signalé l'identification des problèmes et des limitations à prendre en considération pendant le processus de conception.In this thesis, we study the exploration 3D NoC architectures through physical design implementations using real 3D technology used in the industry. Based on the proposed 3D design flow focusing on timing verification by leveraging the benefit of negligible delay of microbumps structure for vertical connections, we have conducted partitioning techniques for 3D NoC-based MPSoC architecture including homogeneous and heterogeneous stacking using Tezzaron 3D IC technlogy. Design and implementation trade-off in both partitioning methods is investigated to have better insight about 3D architecture so that it can be exploited for optimal performance. Using homogeneous 3D stacking approach, NoC architectures are explored to identify the best topology between 2D and 3D topology for 3D MPSoC implementation. The architectural explorations have also considered different process technologies highlighting the wire delay effect to the 3D architecture performance especially for interconnect-dominated design. Additionally, we performed heterogeneous 3D stacking of NoC-based MPSoC implementation with GALS style approach and presented several physical designs related analyses regarding 3D MPSoC design and implementation using 2D EDA tools. Finally we conducted an exploration of 2D EDA tool on different 3D architecture to evaluate the impact of 2D EDA tools on the 3D architecture performance. Since there is no commercialize 3D design tool until now, the experiment is important on the basis that designing 3D architecture using 2D EDA tools does not have a strong and direct impact to the 3D architecture performance mainly because the tools is dedicated for 2D architecture design.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF