Energy efficient anti-collision algorithm for the RFID networks

Energy efficiency is crucial for radio frequency identification (RFID) systems as the readers are often battery operated. The main source of the energy wastage is the collision which happens when tags access the communication medium at the same time. Thus, an efficient anti-collision protocol could minimize the energy wastage and prolong the lifetime of the RFID systems. In this regard, EPCGlobal-Class1-Generation2 (EPC-C1G2) protocol is currently being used in the commercial RFID readers to provide fast tag identification through efficient collision arbitration using the Q algorithm. However, this protocol requires a lot of control message overheads for its operation. Thus, a reinforcement learning based anti-collision protocol (RL-DFSA) is proposed to provide better time system efficiency while being energy efficient through the minimization of control message overheads. The proposed RL-DFSA was evaluated through extensive simulations and compared with the variants of EPC-Class 1 Generation 2 algorithms that are currently being used in the commercial readers. The results show conclusively that the proposed RL-DFSA performs identically to the very efficient EPC-C1G2 protocol in terms of time system efficiency but readily outperforms the compared protocol in the number of control message overhead required for the operation

From M-ary Query to Bit Query: a new strategy for efficient large-scale RFID identification

The tag collision avoidance has been viewed as one of the most important research problems in RFID communications and bit tracking technology has been widely embedded in query tree (QT) based algorithms to tackle such challenge. Existing solutions show further opportunity to greatly improve the reading performance because collision queries and empty queries are not fully explored. In this paper, a bit query (BQ) strategy based Mary query tree protocol (BQMT) is presented, which can not only eliminate idle queries but also separate collided tags into many small subsets and make full use of the collided bits. To further optimize the reading performance, a modified dual prefixes matching (MDPM) mechanism is presented to allow multiple tags to respond in the same slot and thus significantly reduce the number of queries. Theoretical analysis and simulations are supplemented to validate the effectiveness of the proposed BQMT and MDPM, which outperform the existing QT-based algorithms. Also, the BQMT and MDPM can be combined to BQMDPM to improve the reading performance in system efficiency, total identification time, communication complexity and average energy cost

From M-ary Query to Bit Query: a new strategy for efficient large-scale RFID identification

The tag collision avoidance has been viewed as one of the most important research problems in RFID communications and bit tracking technology has been widely embedded in query tree (QT) based algorithms to tackle such challenge. Existing solutions show further opportunity to greatly improve the reading performance because collision queries and empty queries are not fully explored. In this paper, a bit query (BQ) strategy based Mary query tree protocol (BQMT) is presented, which can not only eliminate idle queries but also separate collided tags into many small subsets and make full use of the collided bits. To further optimize the reading performance, a modified dual prefixes matching (MDPM) mechanism is presented to allow multiple tags to respond in the same slot and thus significantly reduce the number of queries. Theoretical analysis and simulations are supplemented to validate the effectiveness of the proposed BQMT and MDPM, which outperform the existing QT-based algorithms. Also, the BQMT and MDPM can be combined to BQMDPM to improve the reading performance in system efficiency, total identification time, communication complexity and average energy cost

Energy aware improved least and most significant bit arbitration algorithm for WORM tags

AbstractPassive Radio Frequency Identification systems have gained enormous attention and popularity especially after its adoption in time and data critical systems. Theoretically, these systems have the potential to read over 100 tags per second in applications which are well insulated from RF noise. Nevertheless, this may not be the case in practical systems, as tag collision is one of the major deterrents affecting the recognition rate. This paper exhaustively analyses the existing probabilistic, deterministic and hybrid algorithms on collision resolutions. In probabilistic algorithms, tags send their entire ID to the RFID reader in respective slots while tags in deterministic algorithms respond bit by bit based on the RFID reader’s query. To minimize identification delay, tag communication overhead and high energy consumption, a new energy efficient collision resolution strategy named Improved Least and Most Significant Bit Algorithm (LaMSBA) is introduced to effectively singulate a tag and increase the identification efficiency in changing tag population even when the bits in tag ID’s are randomly or uniformly distributed. Extensive simulation studies show that LaMSBA can be chosen as better alternatives for dense time and data critical RFID enabled systems. In addition, M/G/1 Queuing model is suitably identified and the the analytical results concluded that LaMSBA is able to maintain the steady state condition even when Class 1 tags arrive at the rate of 15 tags/second in the reader’s interrogation zone

Case Study: Installing RFID Systems in Supermarkets

Radio frequency identification technology (RFID) is considered as the reference technology for wireless identification and item traceability. Supermarkets are one of those scenarios where the RFID potential can be harnessed. In theory, RFID in supermarkets shows several advantages compared with traditional barcode systems, offering real‐time inventory, stock control, cash queues, among others. In practice, its massive and global implementation is still being delayed due to the high quantity of factors that degrade the RFID system performance in these scenarios, causing uncontrolled items and identification losses and, at the end, economical losses. Some works in the scientific literature studied a single or a set of problems related to RFID performance, mostly focused on a specific communication layer: antennas and hardware design, interferences at physical layer, medium access control (MAC) protocols, security issues, or middleware challenges. However, there are no works describing in depth the set of factors affecting RFID performance in a specific scenario and contemplating the entire communication layer stack. The first challenge of this chapter is to provide a complete analysis of those physical and environmental factors, hardware and software limitations, and standard and regulation restrictions that have a direct impact on the RFID system performance in supermarkets. This analysis is addressed by communication layers, paying attention to the point of view of providers, supermarket companies, and final customers. Some of the most feasible and influential research works that address individual problems are also enumerated. Finally, taking the results extracted from this study, this chapter provides a Guide of Good Practices (GGPs), giving a global vision for addressing a successful RFID implementation project, useful for researchers, developers, and installers

RAC-Multi: Reader Anti-Collision Algorithm for Multichannel Mobile RFID Networks

At present, RFID is installed on mobile devices such as mobile phones or PDAs and provides a means to obtain information about objects equipped with an RFID tag over a multi-channeled telecommunication networks. To use mobile RFIDs, reader collision problems should be addressed given that readers are continuously moving. Moreover, in a multichannel environment for mobile RFIDs, interference between adjacent channels should be considered. This work first defines a new concept of a reader collision problem between adjacent channels and then suggests a novel reader anti-collision algorithm for RFID readers that use multiple channels. To avoid interference with adjacent channels, the suggested algorithm separates data channels into odd and even numbered channels and allocates odd-numbered channels first to readers. It also sets an unused channel between the control channel and data channels to ensure that control messages and the signal of the adjacent channel experience no interference. Experimental results show that suggested algorithm shows throughput improvements ranging from 29% to 46% for tag identifications compared to the GENTLE reader anti-collision algorithm for multichannel RFID networks

Passive RFID-Based Inventory of Traffic Signs on Roads and Urban Environments

This paper presents a system with location functionalities for the inventory of traffic signs based on passive RFID technology. The proposed system simplifies the current video-based techniques, whose requirements regarding visibility are difficult to meet in some scenarios, such as dense urban areas. In addition, the system can be easily extended to consider any other street facilities, such as dumpsters or traffic lights. Furthermore, the system can perform the inventory process at night and at a vehicle’s usual speed, thus avoiding interfering with the normal traffic flow of the road. Moreover, the proposed system exploits the benefits of the passive RFID technologies over active RFID, which are typically employed on inventory and vehicular routing applications. Since the performance of passive RFID is not obvious for the required distance ranges on these in-motion scenarios, this paper, as its main contribution, addresses the problem in two different ways, on the one hand theoretically, presenting a radio wave propagation model at theoretical and simulation level for these scenarios; and on the other hand experimentally, comparing passive and active RFID alternatives regarding costs, power consumption, distance ranges, collision problems, and ease of reconfiguration. Finally, the performance of the proposed on-board system is experimentally validated, testing its capabilities for inventory purposesMinisterio de Economía y Competitividad TEC2016-80396-C2-2-

Stability of synchronous queued RFID networks

Queued Radio Frequency Identification (RFID) networks arise naturally in many applications, where tags are grouped into batches, and each batch must be processed before the next reading job starts. In these cases, the system must be able to handle all incoming jobs, keeping the queue backlogs bounded. This property is called stability. Besides, in RFID networks, it is common that some readers cannot operate at the same time, due to mutual interferences. This fact reduces the maximum traffic that readers can process since they have to share the channel. Synchronous networks share the channel using a TDMA approach. The goal of this work is to analytically determine whether a synchronous queued RFID network attains stable operation under a given incoming traffic. Stability depends on the service rate, which is characterized in this paper using an exact numerical method based on a recursive analytical approach, overcoming the limitations of previous works, which were based on simplifications. We also address different flow optimization problems, such as computing the maximum joint traffic that a network can process stably, selecting the minimal number of readers to process a given total load, or determining the optimal timeslot duration, which are novel in the RFID literature.This work was supported by the Project AIM, (AEI/FEDER, EU) under Grant TEC2016-76465-C2-1-R

Stability of synchronous queued RFID networks

Queued Radio Frequency Identification (RFID) networks arise naturally in many applications, where tags are grouped into batches, and each batch must be processed before the next reading job starts. In these cases, the system must be able to handle all incoming jobs, keeping the queue backlogs bounded. This property is called stability. Besides, in RFID networks, it is common that some readers cannot operate at the same time, due to mutual interferences. This fact reduces the maximum traffic that readers can process since they have to share the channel. Synchronous networks share the channel using a TDMA approach. The goal of this work is to analytically determine whether a synchronous queued RFID network attains stable operation under a given incoming traffic. Stability depends on the service rate, which is characterized in this paper using an exact numerical method based on a recursive analytical approach, overcoming the limitations of previous works, which were based on simplifications. We also address different flow optimization problems, such as computing the maximum joint traffic that a network can process stably, selecting the minimal number of readers to process a given total load, or determining the optimal timeslot duration, which are novel in the RFID literature.Ministerio de Economía, Industria y Competitividad | Ref. TEC2016-76465-C2-1-