182 research outputs found
Analysis of Tread ICRs for Wheeled Skid-Steer Vehicles on Inclined Terrain
The instantaneous centers of rotation (ICRs) for the two treads of skid-steer vehicles moving with low inertia on hard horizontal terrain almost remain with constant local coordinates, which allows to establish an equivalence with differential-drive locomotion. However, this significant kinematic relationship has not been analyzed yet on sloped ground. One relevant difficulty of studying ICR behavior on inclined terrain, even on a flat surface, is the continuous variation of pitch and roll angles while turning. To overcome this problem, this paper analyzes a dynamic simulation of a skid-steer vehicle on horizontal ground where gravity is substituted by an equivalent external force in such a way that pitch and roll are kept constant. Relevant tread ICR variations on inclined ground have been deduced, which have a significant impact on skid-steer kinematics. These new findings have been corroborated experimentally with a four-wheeled mobile robot that turns on an inclined plane.Spanish Project PID2021-122944OB-I0
Effects of Turning Radius on Skid-Steered Wheeled Robot Power Consumption on Loose Soil
This research highlights the need for a new power model for skid-steered wheeled robots driving on loose soil and lays the groundwork to develop such a model. State-of-the-art power modeling assumes hard ground; under typical assumptions this predicts constant power consumption over a range of small turning radii where the inner wheels are rotating backwards. However, experimental results performed both in the field and in a controlled laboratory sandbox show that, on sand, power is not in fact constant with respect to turning radius. Power peaks by 20% in a newly identified range of turns where the inner wheels rotate backwards but are being dragged forward. This range of turning radii spans from half the rover width to R', the radius at which the inner wheel is not commanded to turn. Data shows higher motor torque and wheel sinkage in this range. To progress toward predicting the required power for a skid-steered wheeled robot to maneuver on loose soil, a preliminary version of a two-dimensional slip-sinkage model is proposed, along with a model of the force required to bulldoze the pile of sand that accumulates next to the wheels as it they are skidding. However, this is shown to be a less important factor contributing to the increased power in small-radius turns than the added inner wheel torque induced by dragging these wheels through the piles of sand they excavate by counter-rotation (in the identified range of turns). Finally, since a direct application of a power model is to design energy-efficient paths, time dependency of power consumption is also examined. Experiments show reduced rover angular velocity in sand around turning radii where the inner wheels are not rotated and this leads to the introduction to a new parameter to consider in path planning: angular slip
Unmanned Ground Vehicles for Smart Farms
Forecasts of world population increases in the coming decades demand new production processes that are more efficient, safer, and less destructive to the environment. Industries are working to fulfill this mission by developing the smart factory concept. The agriculture world should follow industry leadership and develop approaches to implement the smart farm concept. One of the most vital elements that must be configured to meet the requirements of the new smart farms is the unmanned ground vehicles (UGV). Thus, this chapter focuses on the characteristics that the UGVs must have to function efficiently in this type of future farm. Two main approaches are discussed: automating conventional vehicles and developing specifically designed mobile platforms. The latter includes both wheeled and wheel-legged robots and an analysis of their adaptability to terrain and crops
Model Based On-Line Energy Prediction System for Semi-Autonomous Mobile Robots
Maximizing energy autonomy is a consistent challenge when deploying mobile robots in ionizing radiation or other hazardous environments. Having a reliable robot system is essential for successful execution of missions and to avoid manual recovery of the robots in environments that are harmful to human beings. For deployment of robots missions at short notice, the ability to know beforehand the energy required for performing the task is essential. This paper presents a on-line method for predicting energy requirements based on the pre-determined power models for a mobile robot. A small mobile robot, Khepera III is used for the experimental study and the results are promising with high prediction accuracy. The applications of the energy prediction models in energy optimization and simulations are also discussed along with examples of significant energy savings
Towards autonomous mapping in agriculture: A review of supportive technologies for ground robotics
This paper surveys the supportive technologies currently available for ground mobile robots used for autonomous mapping in agriculture. Unlike previous reviews, we describe state-of-the-art approaches and technologies aimed at extracting information from agricultural environments, not only for navigation purposes but especially for mapping and monitoring. The state-of-the-art platforms and sensors, the modern localization techniques, the navigation and path planning approaches, as well as the potentialities of artificial intelligence towards autonomous mapping in agriculture are analyzed. According to the findings of this review, many examples of recent mobile robots provide full navigation and autonomous mapping capability. Significant resources are currently devoted to this research area, in order to further improve mobile robot capabilities in this complex and challenging field
Heterogeneous Drive Mechanisms for Novel Locomotion in Rough Terrain
The smaller the robot the easier it is for it to access voids in a collapsed structure, however small size brings a host of other problems related to constrained resources. One of the primary constraints on small robots is limited motive power to surmount obstacles and navigate rough terrain. This thesis examines the addition of bulk motive force actuators to existing locomotion platforms and the impact of these heterogeneous actuators on conventional steering methods. The steering methods examined are those associated with skid steered vehicles and differential drive vehicles. In developing the Crabinator, a robot composed of a limbed crawler module and a single track drive module, it appeared that the resulting robot did not fit in the regime of differential drive. For that reason the heterogeneous differential drive class was developed. Similarly for the water hammer active tether module this system also did not appear to be a heterogeneous differential drive or skid steered vehicles. This system turned out to be even more general hence the more general class of heterogeneous drive vehicles which has input of accelerations rather then velocities as the previously mentioned classes
Recommended from our members
Operational criteria for battlefield vehicles
textModern military ground vehicles are no longer able to respond effectively to the rapidly changing mission requirements of modern military conflicts. Military vehicle architectures, which utilize passive suspension components and traditional drivetrain/steering systems, do not provide the operational flexibility to meet the demands of the operator. Advances in intelligent actuation technology allow for the development of a new vehicle architecture - the Intelligent Corner Vehicle (ICV). The ICV utilizes intelligent actuator technology to actively control the four degrees of freedom of each wheel of the vehicle - drive, camber, steering, and suspension. The utilization of intelligent actuation requires the characterization of the motions and behavior of the tire and the vehicle chassis in order to effectively apply the tire to the road surface - the development of vehicle performance criteria. A brief review of the state of wheeled military systems is presented. Many modern military vehicles were designed to improve protection at the expense of mobility - a process that has had negative effects on vehicle capability. An overview of the pneumatic tire used for wheeled vehicles is presented, highlighting the nonlinearities of tire behavior. The complexity of tire force generation drives the need for the application of intelligent actuation. Traditional actuation of wheel motion is presented along with a variety of current efforts to apply intelligent actuation to individual degrees of freedom of the tire. These efforts can be shown to improve vehicle performance, but intelligent actuation must be applied to all aspects of tire motion, requiring the use of the ICV architecture and the generation of performance criteria by which the complex motion of the vehicle may be evaluated. The Robotics Research Group has a history of developing and evaluating performance criteria for complex dynamic systems. and review of performance criteria developed for serial chain robotics is presented. These criteria address task independent actuator motion in addition to actuator ranges and limits, and their application to the ICV is discussed. A brief overview of several important concepts of classical vehicle dynamics are presented. The application of criteria derived from these concepts to the ICV architecture is discussed. This report presents the complexities of tire behavior and vehicle motion, the need for alternative architectures (the ICV), and a variety of performance criteria required to evaluate vehicle motion in real time. Criteria that are presented are summarized along with their definition and physical meaning. Future work for the development of the ICV involves the generation of a vehicle model for evaluating the application and range values of the presented criteria.Mechanical Engineerin
- …