Testing microelectronic biofluidic systems

According to the 2005 International Technology Roadmap for Semiconductors, the integration of emerging nondigital CMOS technologies will require radically different test methods, posing a major challenge for designers and test engineers. One such technology is microelectronic fluidic (MEF) arrays, which have rapidly gained importance in many biological, pharmaceutical, and industrial applications. The advantages of these systems, such as operation speed, use of very small amounts of liquid, on-board droplet detection, signal conditioning, and vast digital signal processing, make them very promising. However, testable design of these devices in a mass-production environment is still in its infancy, hampering their low-cost introduction to the market. This article describes analog and digital MEF design and testing method

Redundant Logic Insertion and Fault Tolerance Improvement in Combinational Circuits

This paper presents a novel method to identify and insert redundant logic into a combinational circuit to improve its fault tolerance without having to replicate the entire circuit as is the case with conventional redundancy techniques. In this context, it is discussed how to estimate the fault masking capability of a combinational circuit using the truth-cum-fault enumeration table, and then it is shown how to identify the logic that can introduced to add redundancy into the original circuit without affecting its native functionality and with the aim of improving its fault tolerance though this would involve some trade-off in the design metrics. However, care should be taken while introducing redundant logic since redundant logic insertion may give rise to new internal nodes and faults on those may impact the fault tolerance of the resulting circuit. The combinational circuit that is considered and its redundant counterparts are all implemented in semi-custom design style using a 32/28nm CMOS digital cell library and their respective design metrics and fault tolerances are compared

Quantifiable Assurance: From IPs to Platforms

Hardware vulnerabilities are generally considered more difficult to fix than software ones because they are persistent after fabrication. Thus, it is crucial to assess the security and fix the vulnerabilities at earlier design phases, such as Register Transfer Level (RTL) and gate level. The focus of the existing security assessment techniques is mainly twofold. First, they check the security of Intellectual Property (IP) blocks separately. Second, they aim to assess the security against individual threats considering the threats are orthogonal. We argue that IP-level security assessment is not sufficient. Eventually, the IPs are placed in a platform, such as a system-on-chip (SoC), where each IP is surrounded by other IPs connected through glue logic and shared/private buses. Hence, we must develop a methodology to assess the platform-level security by considering both the IP-level security and the impact of the additional parameters introduced during platform integration. Another important factor to consider is that the threats are not always orthogonal. Improving security against one threat may affect the security against other threats. Hence, to build a secure platform, we must first answer the following questions: What additional parameters are introduced during the platform integration? How do we define and characterize the impact of these parameters on security? How do the mitigation techniques of one threat impact others? This paper aims to answer these important questions and proposes techniques for quantifiable assurance by quantitatively estimating and measuring the security of a platform at the pre-silicon stages. We also touch upon the term security optimization and present the challenges for future research directions

AI/ML Algorithms and Applications in VLSI Design and Technology

An evident challenge ahead for the integrated circuit (IC) industry in the nanometer regime is the investigation and development of methods that can reduce the design complexity ensuing from growing process variations and curtail the turnaround time of chip manufacturing. Conventional methodologies employed for such tasks are largely manual; thus, time-consuming and resource-intensive. In contrast, the unique learning strategies of artificial intelligence (AI) provide numerous exciting automated approaches for handling complex and data-intensive tasks in very-large-scale integration (VLSI) design and testing. Employing AI and machine learning (ML) algorithms in VLSI design and manufacturing reduces the time and effort for understanding and processing the data within and across different abstraction levels via automated learning algorithms. It, in turn, improves the IC yield and reduces the manufacturing turnaround time. This paper thoroughly reviews the AI/ML automated approaches introduced in the past towards VLSI design and manufacturing. Moreover, we discuss the scope of AI/ML applications in the future at various abstraction levels to revolutionize the field of VLSI design, aiming for high-speed, highly intelligent, and efficient implementations

Modelling and Test Generation for Crosstalk Faults in DSM Chips

In the era of deep submicron technology (DSM), many System-on-Chip (SoC) applications require the components to be operating at high clock speeds. With the shrinking feature size and ever increasing clock frequencies, the DSM technology has led to a well-known problem of Signal Integrity (SI) more especially in the connecting layout design. The increasing aspect ratios of metal wires and also the ratio of coupling capacitance over substrate capacitance result in electrical coupling of interconnects which leads to crosstalk problems. In this thesis, first the work carried out to model the crosstalk behaviour between aggressor and victim by considering the distributed RLGC parameters of interconnect and the coupling capacitance and mutual conductance between the two nets is presented. The proposed model also considers the RC linear models of the CMOS drivers and receivers. The behaviour of crosstalk in case of under etching problem has been studied and modelled by distributing and approximating the defect behaviour throughout the nets. Next, the proposed model has also been extended to model the behaviour of crosstalk in case of one victim is influenced by several aggressors by considering all aggressors have similar effect (worst-case) on victim. In all the above cases simulation experiments were also carried out and compared with well-known circuit simulation tool PSPICE. It has been proved that the generated crosstalk model is faster and the results generated are within 10% of error margin compared to latter simulation tool. Because of the accuracy and speed of the proposed model, the model is very useful for both SoC designers and test engineers to analyse the crosstalk behaviour. Each manufactured device needs to be tested thoroughly to ensure the functionality before its delivery. The test pattern generation for crosstalk faults is also necessary to test the corresponding crosstalk faults. In this thesis, the well-known PODEM algorithm for stuck-at faults is extended to generate the test patterns for crosstalk faults between single aggressor and single victim. To apply modified PODEM for crosstalk faults, the transition behaviour has been divided into two logic parts as before transition and after transition. After finding individually required test patterns for before transition and after transition, the generated logic vectors are appended to create transition test patterns for crosstalk faults. The developed algorithm is also applied for a few ISCAS 85 benchmark circuits and the fault coverage is found excellent in most circuits. With the incorporation of proposed algorithm into the ATPG tools, the efficiency of testing will be improved by generating the test patterns for crosstalk faults besides for the conventional stuck-at faults. In generating test patterns for crosstalk faults on single victim due to multiple aggressors, the modified PODEM algorithm is found to be more time consuming. The search capability of Genetic Algorithms in finding the required combination of several input factors for any optimized problem fascinated to apply GA for generating test patterns as generating the test pattern is also similar to finding the required vector out of several input transitions. Initially the GA is applied for generating test patterns for stuck-at faults and compared the results with PODEM algorithm. As the fault coverage is almost similar to the deterministic algorithm PODEM, the GA developed for stuck-at faults is extended to find test patterns for crosstalk faults between single aggressor and single victim. The elitist GA is also applied for a few ISCAS 85 benchmark circuits. Later the algorithm is extended to generate test patterns for worst-case crosstalk faults. It has been proved that elitist GA developed in this thesis is also very useful in generating test patterns for crosstalk faults especially for multiple aggressor and single victim crosstalk faults

Defect-based testing of LTS digital circuits

A Defect-Based Test (DBT) methodology for Superconductor Electronics (SCE) is presented in this thesis, so that commercial production and efficient testing of systems can be implemented in this technology in the future. In the first chapter, the features and prospects for SCE have been presented. The motivation for this research and the outline of the thesis were also described in Chapter 1. It has been shown that high-end applications such as Software-Defined Radio (SDR) and petaflop computers which are extremely difficult to implement in top-of-the-art semiconductor technologies can be realised using SCE. But, a systematic structural test methodology had yet to be developed for SCE and has been addressed in this thesis. A detailed introduction to Rapid Single-Flux Quantum (RSFQ) circuits was presented in Chapter 2. A Josephson Junction (JJ) was described with associated theory behind its operation. The JJ model used in the simulator used in this research work was also presented. RSFQ logic with logic protocols as well as the design and implementation of an example D-type flip-flop (DFF) was also introduced. Finally, advantages and disadvantages of RSFQ circuits have been discussed with focus on the latest developments in the field. Various techniques for testing RSFQ circuits were discussed in Chapter 3. A Process Defect Monitor (PDM) approach was presented for fabrication process analysis. The presented defect-monitor structures were used to gather measurement data, to find the probability of the occurrence of defects in the process which forms the first step for Inductive Fault Analysis (IFA). Results from measurements on these structures were used to create a database for defects. This information can be used as input for performing IFA. "Defect-sprinkling" over a fault-free circuit can be carried out according to the measured defect densities over various layers. After layout extraction and extensive fault simulation, the resulting information will indicate realistic faults. In addition, possible Design-for-Testability (DfT) schemes for monitoring Single-Flux Quantum (SFQ) pulses within an RSFQ circuit has also been discussed in Chapter 3. The requirement for a DfT scheme is inevitable for RSFQ circuits because of their very high frequency of operation and very low operating temperature. It was demonstrated how SFQ pulses can be monitored at an internal node of an SCE circuit, introducing observability using Test-Point Insertion (TPI). Various techniques were discussed for the introduction of DfT and to avoid the delay introduced by the DfT structure if it is required. The available features in the proposed design for customising the detector make it attractive for a detailed DBT of RSFQ circuits. The control of internal nodes has also been illustrated using TPI. The test structures that were designed and implemented to determine the occurrence of defects in the processes can also be used to locate the position for the insertion of the above mentioned DfT structures

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Autonomous Systems, Robotics, and Computing Systems Capability Roadmap: NRC Dialogue

Contents include the following: Introduction. Process, Mission Drivers, Deliverables, and Interfaces. Autonomy. Crew-Centered and Remote Operations. Integrated Systems Health Management. Autonomous Vehicle Control. Autonomous Process Control. Robotics. Robotics for Solar System Exploration. Robotics for Lunar and Planetary Habitation. Robotics for In-Space Operations. Computing Systems. Conclusion

Design for pre-bond testability in 3D integrated circuits

In this dissertation we propose several DFT techniques specific to 3D stacked IC systems. The goal has explicitly been to create techniques that integrate easily with existing IC test systems. Specifically, this means utilizing scan- and wrapper-based techniques, two foundations of the digital IC test industry. First, we describe a general test architecture for 3D ICs. In this architecture, each tier of a 3D design is wrapped in test control logic that both manages tier test pre-bond and integrates the tier into the large test architecture post-bond. We describe a new kind of boundary scan to provide the necessary test control and observation of the partial circuits, and we propose a new design methodology for test hardcore that ensures both pre-bond functionality and post-bond optimality. We present the application of these techniques to the 3D-MAPS test vehicle, which has proven their effectiveness. Second, we extend these DFT techniques to circuit-partitioned designs. We find that boundary scan design is generally sufficient, but that some 3D designs require special DFT treatment. Most importantly, we demonstrate that the functional partitioning inherent in 3D design can potentially decrease the total test cost of verifying a circuit. Third, we present a new CAD algorithm for designing 3D test wrappers. This algorithm co-designs the pre-bond and post-bond wrappers to simultaneously minimize test time and routing cost. On average, our algorithm utilizes over 90% of the wires in both the pre-bond and post-bond wrappers. Finally, we look at the 3D vias themselves to develop a low-cost, high-volume pre-bond test methodology appropriate for production-level test. We describe the shorting probes methodology, wherein large test probes are used to contact multiple small 3D vias. This technique is an all-digital test method that integrates seamlessly into existing test flows. Our experimental results demonstrate two key facts: neither the large capacitance of the probe tips nor the process variation in the 3D vias and the probe tips significantly hinders the testability of the circuits. Taken together, this body of work defines a complete test methodology for testing 3D ICs pre-bond, eliminating one of the key hurdles to the commercialization of 3D technology.PhDCommittee Chair: Lee, Hsien-Hsin; Committee Member: Bakir, Muhannad; Committee Member: Lim, Sung Kyu; Committee Member: Vuduc, Richard; Committee Member: Yalamanchili, Sudhaka