1,765 research outputs found
On the Energy-Efficiency of Hybrid Analog-Digital Transceivers for Single- and Multi-carrier Large Antenna Array Systems
Hybrid Analog-Digital transceivers are employed with the view to reduce the hardware complexity and the energy consumption in millimeter wave/large antenna array systems by
reducing the number of their Radio Frequency (RF) chains. However, the analog processing network requires power for its operation and it further introduces power losses, dependent on
the number of the transceiver antennas and RF chains, that have to be compensated. Thus, the reduction in the power consumption is usually much less than it is expected and given that the hybrid solutions present in general inferior spectral efficiency than a fully digital one, it is possible for the former to be less energy efficient than the latter in several cases. Existing approaches propose hybrid solutions that maximize the spectral efficiency of the system without providing any insight on their energy requirements/efficiency. To that end, in this paper, a novel algorithmic framework is developed based on which energy efficient hybrid transceiver designs are derived and their performance is examined with respect to the number of RF chains and antennas. Solutions are proposed for fully and partially connected hybrid architectures and for both single- and multi-carrier systems under the Orthogonal Frequency Division Multiplexing (OFDM) modulation. Simulations and theoretical results provide insight on the cases where a hybrid transceiver is the most energy efficient solution or not
Energy efficiency of mmWave massive MIMO precoding with low-resolution DACs
With the congestion of the sub-6 GHz spectrum, the interest in massive
multiple-input multiple-output (MIMO) systems operating on millimeter wave
spectrum grows. In order to reduce the power consumption of such massive MIMO
systems, hybrid analog/digital transceivers and application of low-resolution
digital-to-analog/analog-to-digital converters have been recently proposed. In
this work, we investigate the energy efficiency of quantized hybrid
transmitters equipped with a fully/partially-connected phase-shifting network
composed of active/passive phase-shifters and compare it to that of quantized
digital precoders. We introduce a quantized single-user MIMO system model based
on an additive quantization noise approximation considering realistic power
consumption and loss models to evaluate the spectral and energy efficiencies of
the transmit precoding methods. Simulation results show that
partially-connected hybrid precoders can be more energy-efficient compared to
digital precoders, while fully-connected hybrid precoders exhibit poor energy
efficiency in general. Also, the topology of phase-shifting components offers
an energy-spectral efficiency trade-off: active phase-shifters provide higher
data rates, while passive phase-shifters maintain better energy efficiency.Comment: Published in IEEE Journal of Selected Topics in Signal Processin
Multiuser Precoding and Channel Estimation for Hybrid Millimeter Wave MIMO Systems
In this paper, we develop a low-complexity channel estimation for hybrid
millimeter wave (mmWave) systems, where the number of radio frequency (RF)
chains is much less than the number of antennas equipped at each transceiver.
The proposed channel estimation algorithm aims to estimate the strongest
angle-of-arrivals (AoAs) at both the base station (BS) and the users. Then all
the users transmit orthogonal pilot symbols to the BS via these estimated
strongest AoAs to facilitate the channel estimation. The algorithm does not
require any explicit channel state information (CSI) feedback from the users
and the associated signalling overhead of the algorithm is only proportional to
the number of users, which is significantly less compared to various existing
schemes. Besides, the proposed algorithm is applicable to both non-sparse and
sparse mmWave channel environments. Based on the estimated CSI, zero-forcing
(ZF) precoding is adopted for multiuser downlink transmission. In addition, we
derive a tight achievable rate upper bound of the system. Our analytical and
simulation results show that the proposed scheme offer a considerable
achievable rate gain compared to fully digital systems, where the number of RF
chains equipped at each transceiver is equal to the number of antennas.
Furthermore, the achievable rate performance gap between the considered hybrid
mmWave systems and the fully digital system is characterized, which provides
useful system design insights.Comment: 6 pages, accepted for presentation, ICC 201
Performance evaluation of 5G millimeter-wave cellular access networks using a capacity-based network deployment tool
The next fifth generation (5G) of wireless communication networks comes with a set of new features to satisfy the demand of data-intensive applications: millimeter-wave frequencies, massive antenna arrays, beamforming, dense cells, and so forth. In this paper, we investigate the use of beamforming techniques through various architectures and evaluate the performance of 5G wireless access networks, using a capacity-based network deployment tool. This tool is proposed and applied to a realistic area in Ghent, Belgium, to simulate realistic 5G networks that respond to the instantaneous bit rate required by the active users. The results show that, with beamforming, 5G networks require almost 15% more base stations and 4 times less power to provide more capacity to the users and the same coverage performances, in comparison with the 4G reference network. Moreover, they are 3 times more energy efficient than the 4G network and the hybrid beamforming architecture appears to be a suitable architecture for beamforming to be considered when designing a 5G cellular network
- …