682 research outputs found

    A Control Scheme for an AC-DC Single-Stage Buck-Boost PFC Converter with Improved Output Ripple Reduction

    Get PDF
    AC-DC power factor correction (PFC) single-stage converters are attractive because of their cost and their simplicity. In these converters, both PFC and power conversion are done at the same time using a single converter that regulates the output. Since they have only a single controller, these converters operate with an intermediate transformer primary-side DC bus voltage that is unregulated and is dependent on the converters’ operating conditions and component values. This means that the DC bus voltage can vary significantly as line and load conditions are changed. Such a variable DC bus voltage makes it difficult to optimally design the converter transformer as well as the DC bus capacitor. One previously proposed single-stage AC-DC converter, the Single-Stage Buck-Boost Direct Energy Transfer (SSBBDET) converter has a clamping mechanism that can clamp the DC bus voltage to a pre-set limit. The clamping mechanism, however, superimposes a low frequency 120 Hz AC component on the output DC voltage so that some means must be taken to reduce this component. These means, however, make the converter transient slow and sluggish. The main objective of this thesis is to minimize the 120 Hz output ripple component and to improve the dynamic response of the SSBBDET converter by using a new control scheme. In the thesis, the operation of the SSBBDET converter is reviewed and the proposed control method is introduced and explained in detail. Key design considerations for the design of the converter controller are discussed and the converter’s ability to operate with fixed DC bus voltage, low output ripple and fast dynamic response is confirmed with experimental results obtained from a prototype converter

    A ripple reduction method for a two stages battery charger with multi-winding transformer using notch filter

    Get PDF
    This paper presents a two-stage battery charger consisting of a bridgeless Totem-pole power factor correction (TP-PFC) circuit and a full bridge converter with a multi-winding transformer. By using this transformer the cell equalizing operation can be achieved with no additional circuitry. In addition, a double-line frequency ripple reduction method is proposed to address the low frequency current ripples issues existing in both primary and secondary winding of the transformer which is caused by the voltage ripples across the intermediate DC link bus. Control and analysis of the converter at different operation modes is illustrated in detail and simulation results validate the effectiveness of the proposed converter and control algorithm

    A plug-and-play ripple mitigation approach for DC-links in hybrid systems

    Get PDF
    © 2016 IEEE.In this paper, a plug-and-play ripple mitigation technique is proposed. It requires only the sensing of the DC-link voltage and can operate fully independently to remove the low-frequency voltage ripple. The proposed technique is nonintrusive to the existing hardware and enables hot-swap operation without disrupting the normal functionality of the existing power system. It is user-friendly, modular and suitable for plug-and-play operation. The experimental results demonstrate the effectiveness of the ripple-mitigation capability of the proposed device. The DC-link voltage ripple in a 110 W miniature hybrid system comprising an AC/DC converter and two resistive loads is shown to be significantly reduced from 61 V to only 3.3 V. Moreover, it is shown that with the proposed device, the system reliability has been improved by alleviating the components' thermal stresses

    Low Cost AC/DC converter with Power Factor Correction

    Get PDF
    A high performance single stage Power Factor Correction (PFC) converter with tight output voltage regulation and a very simple circuit to carry out those functions, which means its cost is lower than its counterparts. Two basic flyback circuits include a simple control circuit. For the hard switching circuit, only one switch is used to achieve low cost; for the soft switching scheme, one auxiliary switch is added to get higher efficiency and smaller size. There are two power flow paths, resulting in part power processed by an active switch only once to reduce the current stress and improve the efficiency. A direct current (DC) bus voltage will be limited to the peak value of input voltage. The maximum DC bus voltage will be less than 400 and a single commercial capacitor can be used for universal voltage stress under light load condition

    Energy Saving Drives New Approaches to Telecommunications Power System

    Get PDF

    Power quality improvements of arc welding power supplies by modified bridgeless SEPIC PFC converter

    Get PDF
    This paper proposes an efficient bridgeless power factor corrected (PFC) modified single ended primary inductor converter (SEPIC) for arc welding power supplies (AWPS). The overall configuration is composed of two converters: (1) a modified bridgeless SEPIC PFC converter, which is controlled by a PI controller to achieve a high power factor and fast response; and (2) a full bridge buck converter with high-frequency transformer for high-frequency isolation to ensure arc welding stability. The proposed system is simulated under different operating conditions of an AWPS. It is also tested in real time by a hardware-in-the-loop system based on a dSPACE DS1103 control board. The system performances are evaluated based on power quality indices such as power factor, total harmonic distortions of the AC grid current, and voltage regulation. The obtained results show that the proposed controller enhances the weld bead quality by keeping a constant current at the output and a stable arc, meet the international power quality standards and robustness for voltage regulation

    A New Single-Phase Single-Stage AC-DC Stacked Flyback Converter With Active Clamp ZVS

    Get PDF
    Single-stage AC-DC converters integrate an AC-DC front-end converter with a DC-DC back-end converter. Compared with conventional two-stage AC-DC converters, single-stage AC-DC converters use less components and only one controller, which is used to regulate the output voltage. As a result, the cost, size and complexity of AC-DC converters can be reduced, but single-stage converters do not perform as well as two-stage converters, and most have drawbacks that are related to the fact that the DC bus voltage is not controlled an can become excessive. A new single-phase single-stage AC-DC converter that uses stacked flyback converters is proposed in this thesis. The proposed converter consists of two low power flyback converters stacked on top of each other and an active clamp that helps the main switches operate with ZVS. The stacked structure helps reduce the voltage stresses typical fund in many single-stage converters. In the thesis, the operation of the converter is explained, the steady-state characteristics of the converter are determined and its design is discussed. The feasibility of the new converter is confirmed with experimental results obtained from a 100VAC~220VAC worldwide input, 48V output, 100kHz switching frequency and 200 W output power prototype converter

    Single-Stage Power Electronic Converters with Combined Voltage Step-Up/Step-Down Capability

    Get PDF
    Power electronic converters are typically either step-down converters that take an input voltage and produce an output voltage of low amplitude or step-up converters that take an input voltage and produce an output voltage of higher amplitude. There are, however, applications where a converter that can step-up voltage or step-down voltage can be very useful, such as in applications where a converter needs to operate under a wide range of input and output voltage conditions such as a grid-connected solar inverter. Such converters, however, are not as common as converters that can only step down or step up voltage because most applications require converters that need to only step down voltage or only step up voltage and such converters have better performance within a limited voltage range than do converters that are designed for very wide voltage ranges. Nonetheless, there are applications where converters with step-down and step-up capability can be used advantageously. The main objectives of this thesis are to propose new power electronic converters that can step up voltage and step down voltage and to investigate their characteristics. This will be done for two specific converter types: AC/DC single-stage converters and DC-AC inverters. In this thesis, two new AC/DC single-stage converters and a new three-phase converter are proposed and their operation and steady-state characteristics are examined in detail. The feasibility of each new converter is confirmed with results obtained from an experimental prototype and the feasibility of a control method for the inverter is confirmed with simulation work using commercially available software such as MATLAB and PSIM

    A Bidirectional Soft-Switched DAB-Based Single-Stage Three-Phase AC–DC Converter for V2G Application

    Get PDF
    In vehicle-to-grid applications, the battery charger of the electric vehicle (EV) needs to have a bidirectional power flow capability. Galvanic isolation is necessary for safety. An ac-dc bidirectional power converter with high-frequency isolation results in high power density, a key requirement for an on-board charger of an EV. Dual-active-bridge (DAB) converters are preferred in medium power and high voltage isolated dc-dc converters due to high power density and better efficiency. This paper presents a DAB-based three-phase ac-dc isolated converter with a novel modulation strategy that results in: 1) single-stage power conversion with no electrolytic capacitor, improving the reliability and power density; 2) open-loop power factor correction; 3) soft-switching of all semiconductor devices; and 4) a simple linear relationship between the control variable and the transferred active power. This paper presents a detailed analysis of the proposed operation, along with simulation results and experimental verification

    Optimization And Design Of Photovoltaic Micro-inverter

    Get PDF
    To relieve energy shortage and environmental pollution issues, renewable energy, especially PV energy has developed rapidly in the last decade. The micro-inverter systems, with advantages in dedicated PV power harvest, flexible system size, simple installation, and enhanced safety characteristics are the future development trend of the PV power generation systems. The double-stage structure which can realize high efficiency with nice regulated sinusoidal waveforms is the mainstream for the micro-inverter. This thesis studied a double stage micro-inverter system. Considering the intermittent nature of PV power, a PFC was analyzed to provide additional electrical power to the system. When the solar power is less than the load required, PFC can drag power from the utility grid. In the double stage micro-inverter, the DC/DC stage was realized by a LLC converter, which could realize soft switching automatically under frequency modulation. However it has a complicated relationship between voltage gain and load. Thus conventional variable step P&O MPPT techniques for PWM converter were no longer suitable for the LLC converter. To solve this problem, a novel MPPT was proposed to track MPP efficiently. Simulation and experimental results verified the effectiveness of the proposed MPPT. The DC/AC stage of the micro-inverter was realized by a BCM inverter. With duty cycle and frequency modulation, ZVS was achieved through controlling the inductor current bi-directional in every switching cycle. This technique required no additional resonant components and could be employed for low power applications on conventional full-bridge and half-bridge inverter topologies. Three different current mode control schemes were derived from the basic theory of the proposed technique. They were referred to as Boundary Current Mode (BCM), Variable Hysteresis Current Mode (VHCM), and Constant Hysteresis Current Mode (CHCM) individually in this paper with their advantages and disadvantages analyzed in detail. Simulation and experimental iv results demonstrated the feasibilities of the proposed soft-switching technique with the digital control schemes. The PFC converter was applied by a single stage Biflyback topology, which combined the advantages of single stage PFC and flyback topology together, with further advantages in low intermediate bus voltage and current stresses. A digital controller without current sampling requirement was proposed based on the specific topology. To reduce the voltage spike caused by the leakage inductor, a novel snubber cell combining soft switching technique with snubber technique together was proposed. Simulation and experimental waveforms illustrated the same as characteristics as the theoretical analysis. In summary, the dissertation analyzed each power stage of photovoltaic micro-inverter system from efficiency and effectiveness optimization perspectives. Moreover their advantages were compared carefully with existed topologies and control techniques. Simulation and experiment results were provided to support the theoretical analysis
    corecore