Built-in-self-test of RF front-end circuitry

Fuelled by the ever increasing demand for wireless products and the advent of deep submicron CMOS, RF ICs have become fairly commonplace in the semiconductor market. This has given rise to a new breed of Systems-On-Chip (SOCs) with RF front-ends tightly integrated along with digital, analog and mixed signal circuitry. However, the reliability of the integrated RF front-end continues to be a matter of significant concern and considerable research. A major challenge to the reliability of RF ICs is the fact that their performance is also severely degraded by wide tolerances in on-chip passives and package parasitics, in addition to process related faults. Due to the absence of contact based testing solutions in embedded RF SOCs (because the very act of probing may affect the performance of the RF circuit), coupled with the presence of very few test access nodes, a Built In Self Test approach (BiST) may prove to be the most efficient test scheme. However due to the associated challenges, a comprehensive and low-overhead BiST methodology for on-chip testing of RF ICs has not yet been reported in literature. In the current work, an approach to RF self-test that has hitherto been unexplored both in literature and in the commercial arena is proposed. A sensitive current monitor has been used to extract variations in the supply current drawn by the circuit-under-test (CUT). These variations are then processed in time and frequency domain to develop signatures. The acquired signatures can then be mapped to specific behavioral anomalies and the locations of these anomalies. The CUT is first excited by simple test inputs that can be generated on-chip. The current monitor extracts the corresponding variations in the supply current of the CUT, thereby creating signatures that map to various performance metrics of the circuit. These signatures can then be post-processed by low overhead on-chip circuitry and converted into an accessible form. To be successful in the RF domain any BIST architecture must be minimally invasive, reliable, offer good fault coverage and present low real estate and power overheads. The current-based self-test approach successfully addresses all these concerns. The technique has been applied to RF Low Noise Amplifiers, Mixers and Voltage Controlled Oscillators. The circuitry and post-processing techniques have also been demonstrated in silicon (using the IBM 0.25 micron RF CMOS process). The entire self-test of the RF front-end can be accomplished with a total test time of approximately 30µs, which is several orders of magnitude better than existing commercial test schemes

FPGA ARCHITECTURE AND VERIFICATION OF BUILT IN SELF-TEST (BIST) FOR 32-BIT ADDER/SUBTRACTER USING DE0-NANO FPGA AND ANALOG DISCOVERY 2 HARDWARE

The integrated circuit (IC) is an integral part of everyday modern technology, and its application is very attractive to hardware and software design engineers because of its versatility, integration, power consumption, cost, and board area reduction. IC is available in various types such as Field Programming Gate Array (FPGA), Application Specific Integrated Circuit (ASIC), System on Chip (SoC) architecture, Digital Signal Processing (DSP), microcontrollers (μC), and many more. With technology demand focused on faster, low power consumption, efficient IC application, design engineers are facing tremendous challenges in developing and testing integrated circuits that guaranty functionality, high fault coverage, and reliability as the transistor technology is shrinking to the point where manufacturing defects of ICs are affecting yield which associates with the increased cost of the part. The competitive IC market is pressuring manufactures of ICs to develop and market IC in a relatively quick turnaround which in return requires design and verification engineers to develop an integrated self-test structure that would ensure fault-free and the quality product is delivered on the market. 70-80% of IC design is spent on verification and testing to ensure high quality and reliability for the enduser. To test complex and sophisticated IC designs, the verification engineers must produce laborious and costly test fixtures which affect the cost of the part on the competitive market. To avoid increasing the part cost due to yield and test time to the end-user and to keep up with the competitive market many IC design engineers are deviating from complex external test fixture approach and are focusing on integrating Built-in Self-Test (BIST) or Design for Test (DFT) techniques onto IC’s which would reduce time to market but still guarantee high coverage for the product. Understanding the BIST, the architecture, as well as the application of IC, must be understood before developing IC. The architecture of FPGA is elaborated in this paper followed by several BIST techniques and applications of those BIST relative to FPGA, SoC, analog to digital (ADC), or digital to analog converters (DAC) that are integrated on IC. Paper is concluded with verification of BIST for the 32-bit adder/subtracter designed in Quartus II software using the Analog Discovery 2 module as stimulus and DE0-NANO FPGA board for verification

A Discrete Event System approach to On-line Testing of digital circuits with measurement limitation

AbstractIn the present era of complex systems like avionics, industrial processes, electronic circuits, etc., on-the-fly or on-line fault detection is becoming necessary to provide uninterrupted services. Measurement limitation based fault detection schemes are applied to a wide range of systems because sensors cannot be deployed in all the locations from which measurements are required. This paper focuses towards On-Line Testing (OLT) of faults in digital electronic circuits under measurement limitation using the theory of discrete event systems. Most of the techniques presented in the literature on OLT of digital circuits have emphasized on keeping the scheme non-intrusive, low area overhead, high fault coverage, low detection latency etc. However, minimizing tap points (i.e., measurement limitation) of the circuit under test (CUT) by the on-line tester was not considered. Minimizing tap points reduces load on the CUT and this reduces the area overhead of the tester. However, reduction in tap points compromises fault coverage and detection latency. This work studies the effect of minimizing tap points on fault coverage, detection latency and area overhead. Results on ISCAS89 benchmark circuits illustrate that measurement limitation have minimal impact on fault coverage and detection latency but reduces the area overhead of the tester. Further, it was also found that for a given detection latency and fault coverage, area overhead of the proposed scheme is lower compared to other similar schemes reported in the literature

Symmetry-based A/M-S BIST (SymBIST): Demonstration on a SAR ADC IP

International audienceIn this paper, we propose a defect-oriented Built-In Self-Test (BIST) paradigm for analog and mixed-signal (A/M-S) Integrated Circuits (ICs), called symmetry-based BIST (Sym-BIST). SymBIST exploits inherent symmetries into the design to generate invariances that should hold true only in defect-free operation. Violation of any of these invariances points to defect detection. We demonstrate SymBIST on a 65nm 10-bit Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) IP by ST Microelectronics

Software-Based Self-Test of Set-Associative Cache Memories

Embedded microprocessor cache memories suffer from limited observability and controllability creating problems during in-system tests. This paper presents a procedure to transform traditional march tests into software-based self-test programs for set-associative cache memories with LRU replacement. Among all the different cache blocks in a microprocessor, testing instruction caches represents a major challenge due to limitations in two areas: 1) test patterns which must be composed of valid instruction opcodes and 2) test result observability: the results can only be observed through the results of executed instructions. For these reasons, the proposed methodology will concentrate on the implementation of test programs for instruction caches. The main contribution of this work lies in the possibility of applying state-of-the-art memory test algorithms to embedded cache memories without introducing any hardware or performance overheads and guaranteeing the detection of typical faults arising in nanometer CMOS technologie

The integration of on-line monitoring and reconfiguration functions using IEEE1149.4 into a safety critical automotive electronic control unit.

This paper presents an innovative application of IEEE 1149.4 and the integrated diagnostic reconfiguration (IDR) as tools for the implementation of an embedded test solution for an automotive electronic control unit, implemented as a fully integrated mixed signal system. The paper describes how the test architecture can be used for fault avoidance with results from a hardware prototype presented. The paper concludes that fault avoidance can be integrated into mixed signal electronic systems to handle key failure modes

Dynamic input match correction in R.F. low noise amplifiers

An R.F. circuit that recognizes its faults, and then corrects its performance in real-time has been the holy-grail of RFIC design. This work presents, for the first time, a complete architecture and successful implementation of such a circuit. It is the first step towards the grand vision of fault-free, package independent, integrated R.F. Front End circuitry. The performance of R.F. front-end circuitry can degrade significantly due to process faults and parasitic package inductances at its input. These inductances have wide tolerances and are difficult to co-design for. A novel methodology, which overcomes current obstacles plaguing such an objective, is proposed wherein the affected performance metric of the circuit is quantified, and the appropriate design parameter is modified in real-time, thus enabling self-correction. This proof of concept is demonstrated by designing a cascode LNA and the complete self-correction circuit in IBM 0.25 µm CMOS RF process. The self-correction circuitry ascertains the input match frequency of the circuit by measuring its performance and determines the frequency interval by which it needs to be shifted to restore it to the desired value. It then feeds back a digital word to the LNA which adaptively corrects its input-match. It offers the additional flexibility of using different packages for the front-end since it renders the circuitry independent of package parasitics, by re-calibrating the input match on-the-fly. The circuitry presented in this work offers the advantages of low power, robustness, absence of DSP cores or processors, reduction in design cycle times, guaranteed optimal performance under varying conditions and fast correction times (less than 30 µs)

Fault-tolerant design of RF front-end circuits

The continuing trends of scaling in the CMOS industry have, inevitably, been accompanied by an ever-increasing array of process faults and fabrication complexities. The relentless march towards miniaturization and massive integration, in addition to increasing operating frequencies has resulted in increasing concerns about the reliability of integrated RF front-ends. Coupled with rising cost per chip, the fault-tolerant paradigm has become pertinent in the RFIC domain. Two main reasons have contributed to the fact that fault-tolerant solutions for circuits that operate in the GHz domain have not been realized so far. First, GHz signals are extremely sensitive to higher-order effects such as stray pick-ups, interference, package & on-chip parasitics, etc. Secondly, the use of passives, especially inductors, in the feedback path poses huge area overheads, in addition to a slew of instability problems due to wide variations and soft faults. Hence traditional fault-tolerance methods used in digital and low frequency analog circuits cannot be applied in the RF domain. This work presents a unique methodology to achieve fault-tolerance in RF circuits through dynamic sensing and on-chip self-correction, along with the development of robust algorithms. This technique is minimally intrusive and is transparent during \u27normal\u27 use of the circuit. It is characterized by low area and power overheads, does not need any off-chip computing or DSP cores, and is characterized by self-correction times in the range of a few hundreds of microseconds. It compares very well with existing commercial RF test solutions that use DSP cores and require hundreds of milliseconds. The methodology is demonstrated on a LNA, since it is critical for the performance of the entire front-end. It is validated with simulation and fabrication results of the system designed in IBM 0.25 µm CMOS 6RF process

Methodologies and Toolflows for the Predictable Design of Reliable and Low-Power NoCs

There is today the unmistakable need to evolve design methodologies and tool ows for Network-on-Chip based embedded systems. In particular, the quest for low-power requirements is nowadays a more-than-ever urgent dilemma. Modern circuits feature billion of transistors, and neither power management techniques nor batteries capacity are able to endure the increasingly higher integration capability of digital devices. Besides, power concerns come together with modern nanoscale silicon technology design issues. On one hand, system failure rates are expected to increase exponentially at every technology node when integrated circuit wear-out failure mechanisms are not compensated for. However, error detection and/or correction mechanisms have a non-negligible impact on the network power. On the other hand, to meet the stringent time-to-market deadlines, the design cycle of such a distributed and heterogeneous architecture must not be prolonged by unnecessary design iterations. Overall, there is a clear need to better discriminate reliability strategies and interconnect topology solutions upfront, by ranking designs based on power metric. In this thesis, we tackle this challenge by proposing power-aware design technologies. Finally, we take into account the most aggressive and disruptive methodology for embedded systems with ultra-low power constraints, by migrating NoC basic building blocks to asynchronous (or clockless) design style. We deal with this challenge delivering a standard cell design methodology and mainstream CAD tool ows, in this way partially relaxing the requirement of using asynchronous blocks only as hard macros

Degradation in FPGAs: Monitoring, Modeling and Mitigation

This dissertation targets the transistor aging degradation as well as the associated thermal challenges in FPGAs (since there is an exponential relation between aging and chip temperature). The main objectives are to perform experimentation, analysis and device-level model abstraction for modeling the degradation in FPGAs, then to monitor the FPGA to keep track of aging rates and ultimately to propose an aging-aware FPGA design flow to mitigate the aging