High Performance Power Management Integrated Circuits for Portable Devices

abstract: Portable devices often require multiple power management IC (PMIC) to power different sub-modules, Li-ion batteries are well suited for portable devices because of its small size, high energy density and long life cycle. Since Li-ion battery is the major power source for portable device, fast and high-efficiency battery charging solution has become a major requirement in portable device application. In the first part of dissertation, a high performance Li-ion switching battery charger is proposed. Cascaded two loop (CTL) control architecture is used for seamless CC-CV transition, time based technique is utilized to minimize controller area and power consumption. Time domain controller is implemented by using voltage controlled oscillator (VCO) and voltage controlled delay line (VCDL). Several efficiency improvement techniques such as segmented power-FET, quasi-zero voltage switching (QZVS) and switching frequency reduction are proposed. The proposed switching battery charger is able to provide maximum 2 A charging current and has an peak efficiency of 93.3%. By configure the charger as boost converter, the charger is able to provide maximum 1.5 A charging current while achieving 96.3% peak efficiency. The second part of dissertation presents a digital low dropout regulator (DLDO) for system on a chip (SoC) in portable devices application. The proposed DLDO achieve fast transient settling time, lower undershoot/overshoot and higher PSR performance compared to state of the art. By having a good PSR performance, the proposed DLDO is able to power mixed signal load. To achieve a fast load transient response, a load transient detector (LTD) enables boost mode operation of the digital PI controller. The boost mode operation achieves sub microsecond settling time, and reduces the settling time by 50% to 250 ns, undershoot/overshoot by 35% to 250 mV and 17% to 125 mV without compromising the system stability.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Control techniques for power system stabilisation

The conventional PSS was first proposed earlier based on a linear model of the power system to damp the low frequency oscillations in the system. But they are designed to be operated under fixed parameters derived from the system linearized model. Due to large interconnection of power system to meet the load demand brings in deviations of steady-state and non-linearity to power system. The main problem is that PSS includes the locally measured quantities only neglecting the effect of nearby generators. This is the reason for the advent of Wide area monitoring for strong coupling between the local modes and the inter-area modes which would make the tuning of local PSSs for damping all modes nearly impossible when there is no supervisory level controller. Wide area control addresses these problems by proposing smart topology changes and control actions. Dynamic islanding and fast load shedding are schemes available to maintain as much as possible healthy transmission system. It is found that if remote signals from one or more distant locations of the power system can be applied to local controller design, system dynamic performance can be enhanced. In order to attain these goals, it is desirable to systematically build a robust wide area controller model within an autonomous system framework

Analysis on Supercapacitor Assisted Low Dropout (SCALDO) Regulators

State-of-the-art electronic systems employ three fundamental techniques for DC-DC converters: (a) switch-mode power supplies (SMPS); (b) linear power supplies; (c) switched capacitor (charge pump) converters. In practical systems, these three techniques are mixed to provide a complex, but elegant, overall solution, with energy efficiency, effective PCB footprint, noise and transient performance to suit different electronic circuit blocks. Switching regulators have relatively high end-to-end efficiency, in the range of 70 to 93%, but can have issues with output noise and EMI/RFI emissions. Switched capacitor converters use a set of capacitors for energy storage and conversion. In general, linear regulators have low efficiencies in the range 30 to 60%. However, they have outstanding output characteristics such as low noise, excellent transient response to load current fluctuations, design simplicity and low cost design which are far superior to SMPS. Given the complex situation in switch-mode converters, low dropout (LDO) regulators were introduced to address the equirements of noise-sensitive and fast transient loads in portable devices. A typical commercial off-the-shelf LDO has its input voltage slightly higher than the desired regulated output for optimal efficiency. The approximate efficiency of a linear regulator, if the power consumed by the control circuits is negligible, can be expressed by the ratio of Vo/Vin. A very low frequency supercapacitor circulation technique can be combined with commercial low dropout regulator ICs to significantly increase the end-to-end efficiency by a multiplication factor in the range of 1.33 to 3, compared to the efficiency of a linear regulator circuit with the same input-output voltages. In this patented supercapacitor-assisted low dropout (SCALDO) regulator technique developed by a research team at the University of Waikato, supercapacitors are used as lossless voltage droppers, and the energy reuse occurs at very low frequencies in the range of less than ten hertz, eliminating RFI/EMI concerns. This SCALDO technique opens up a new approach to design step-down, DC-DC converters suitable for processor power supplies with very high end-to-end efficiency which is closer to the efficiencies of practical switching regulators, while maintaining the superior output specifications of a linear design. Furthermore, it is important to emphasize that the SCALDO technique is not a variation of well-known switched capacitor DC-DC converters. In this thesis, the basic SCALDO concept is further developed to achieve generalised topologies, with the relevant theory that can be applied to a converter with any input-output step-down voltage combination. For these generalised topologies, some important design parameters, such as the number of supercapacitors, switching matrix details and efficiency improvement factors, are derived to form the basis of designing SCALDO regulators. With the availability of commercial LDO ICs with output current ratings up to 10 A, and thin-prole supercapacitors with DC voltage ratings from 2.3 to 5.5 V, several practically useful, medium-current SCALDO prototypes: 12V-to-5V, 5V-to-2V, 5.5V-to-3.3V have been developed. Experimental studies were carried out on these SCALDO prototypes to quantify performance in terms of line regulation, load regulation, efficiency and transient response. In order to accurately predict the performance and associated waveforms of the individual phases (charge, discharge and transition) of the SCALDO regulator, Laplace transform-based theory for supercapacitor circulation is developed, and analytical predictions are compared with experimental measurements for a 12V-to-5V prototype. The analytical results tallied well with the practical waveforms observed in a 12V-to-5V converter, indicating that the SCALDO technique can be generalized to other versatile configurations, and confirming that the simplified assumptions used to describe the circuit elements are reasonable and justifiable. After analysing the performance of several SCALDO prototypes, some practical issues in designing SCALDO regulators have been identified. These relate to power losses and implications for future development of the SCALDO design

Power Management ICs for Internet of Things, Energy Harvesting and Biomedical Devices

This dissertation focuses on the power management unit (PMU) and integrated circuits (ICs) for the internet of things (IoT), energy harvesting and biomedical devices. Three monolithic power harvesting methods are studied for different challenges of smart nodes of IoT networks. Firstly, we propose that an impedance tuning approach is implemented with a capacitor value modulation to eliminate the quiescent power consumption. Secondly, we develop a hill-climbing MPPT mechanism that reuses and processes the information of the hysteresis controller in the time-domain and is free of power hungry analog circuits. Furthermore, the typical power-performance tradeoff of the hysteresis controller is solved by a self-triggered one-shot mechanism. Thus, the output regulation achieves high-performance and yet low-power operations as low as 12 µW. Thirdly, we introduce a reconfigurable charge pump to provide the hybrid conversion ratios (CRs) as 1⅓× up to 8× for minimizing the charge redistribution loss. The reconfigurable feature also dynamically tunes to maximum power point tracking (MPPT) with the frequency modulation, resulting in a two-dimensional MPPT. Therefore, the voltage conversion efficiency (VCE) and the power conversion efficiency (PCE) are enhanced and flattened across a wide harvesting range as 0.45 to 3 V. In a conclusion, we successfully develop an energy harvesting method for the IoT smart nodes with lower cost, smaller size, higher conversion efficiency, and better applicability. For the biomedical devices, this dissertation presents a novel cost-effective automatic resonance tracking method with maximum power transfer (MPT) for piezoelectric transducers (PT). The proposed tracking method is based on a band-pass filter (BPF) oscillator, exploiting the PT’s intrinsic resonance point through a sensing bridge. It guarantees automatic resonance tracking and maximum electrical power converted into mechanical motion regardless of process variations and environmental interferences. Thus, the proposed BPF oscillator-based scheme was designed for an ultrasonic vessel sealing and dissecting (UVSD) system. The sealing and dissecting functions were verified experimentally in chicken tissue and glycerin. Furthermore, a combined sensing scheme circuit allows multiple surgical tissue debulking, vessel sealer and dissector (VSD) technologies to operate from the same sensing scheme board. Its advantage is that a single driver controller could be used for both systems simplifying the complexity and design cost. In a conclusion, we successfully develop an ultrasonic scalpel to replace the other electrosurgical counterparts and the conventional scalpels with lower cost and better functionality

Design of low-dropout regulator for ultra low power on-chip applications

Low Drop Out (LDO) voltage regulators are commonly used to supply low-voltage digital circuits such as microprocessor cores. These digital circuits normally are continuously changing from one mode of operation to another. Therefore, the load demand can change rapidly resulting in large voltage transients at the output of the regulator which can adversely affect the digital circuitry. In this Master's Thesis, design topologies and challenges of very low-power fully integrated On-Chip Low-Dropout (LDO) regulators have been analyzed. Instead of conventional LDO which makes use of a large external capacitor to have better dynamic response and stability, a CapacitorLess LDO (CL-LDO) is chosen on considerations of smaller area. The most challenging part of designing this kind of regulator is achieving high current efficiency by reducing the quiescent current while ensuring good stability response as well as good regulation performance. Thus, different circuit techniques must be carefully added in order to balance the lack of the large external capacitor having the minimum impact on system efficiency. This work focuses on designing a fully integrated low-dropout regulator with good dynamic performance, high regulation performance and ultra-low power consumption. The stability is achieved by the use of two pole-splitting techniques, namely Cascode and Nested-Miller compensation. The good dynamic response with low quiescent current are achieved by the use of an adaptive biasing circuit, a gm-boost circuit and adaptive power transistor architecture

High efficiency smart voltage regulating module for green mobile computing

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In this thesis a design for a smart high efficiency voltage regulating module capable of supplying the core of modern microprocessors incorporating dynamic voltage and frequency scaling (DVS) capability is accomplished using a RISC based microcontroller to facilitate all the functions required to control, protect, and supply the core with the required variable operating voltage as set by the DVS management system. Normally voltage regulating modules provide maximum power efficiency at designed peak load, and the efficiency falls off as the load moves towards lesser values. A mathematical model has been derived for the main converter and small signal analysis has been performed in order to determine system operation stability and select a control scheme that would improve converter operation response to transients and not requiring intense computational power to realize. A Simulation model was built using Matlab/Simulink and after experimenting with tuned PID controller and fuzzy logic controllers, a simple fuzzy logic control scheme was selected to control the pulse width modulated converter and several methods were devised to reduce the requirements for computational power making the whole system operation realizable using a low power RISC based microcontroller. The same microcontroller provides circuit adaptations operation in addition to providing protection to load in terms of over voltage and over current protection. A novel circuit technique and operation control scheme enables the designed module to selectively change some of the circuit elements in the main pulse width modulated buck converter so as to improve efficiency over a wider range of loads. In case of very light loads as the case when the device goes into standby, sleep or hibernation mode, a secondary converter starts operating and the main converter stops. The secondary converter adapts a different operation scheme using switched capacitor technique which provides high efficiency at low load currents. A fuzzy logic control scheme was chosen for the main converter for its lighter computational power requirement promoting implementation using ultra low power embedded controllers. Passive and active components were carefully selected to augment operational efficiency. These aspects enabled the designed voltage regulating module to operate with efficiency improvement in off peak load region in the range of 3% to 5%. At low loads as the case when the computer system goes to standby or sleep mode, the efficiency improvent is better than 13% which will have noticeable contribution in extending battery run time thus contributing to lowering the carbon footprint of human consumption

Distributed IC Power Delivery: Stability-Constrained Design Optimization and Workload-Aware Power Management

ABSTRACT Power delivery presents key design challenges in today’s systems ranging from high performance micro-processors to mobile systems-on-a-chips (SoCs). A robust power delivery system is essential to ensure reliable operation of on-die devices. Nowadays it has become an important design trend to place multiple voltage regulators on-chip in a distributive manner to cope with power supply noise. However, stability concern arises because of the complex interactions be-tween multiple voltage regulators and bulky network of the surrounding passive parasitics. The recently developed hybrid stability theorem (HST) is promising to deal with the stability of such system by efficiently capturing the effects of all interactions, however, large overdesign and hence severe performance degradation are caused by the intrinsic conservativeness of the underlying HST framework. To address such challenge, this dissertation first extends the HST by proposing a frequency-dependent system partitioning technique to substantially reduce the pessimism in stability evaluation. By systematically exploring the theoretical foundation of the HST framework, we recognize all the critical constraints under which the partitioning technique can be performed rigorously to remove conservativeness while maintaining key theoretical properties of the partitioned subsystems. Based on that, we develop an efficient stability-ensuring automatic design flow for large power delivery systems with distributed on-chip regulation. In use of the proposed approach, we further discover new design insights for circuit designers such as how regulator topology, on-chip decoupling capacitance, and the number of integrated voltage regulators can be optimized for improved system tradeoffs between stability and performances. Besides stability, power efficiency must be improved in every possible way while maintaining high power quality. It can be argued that the ultimate power integrity and efficiency may be best achieved via a heterogeneous chain of voltage processing starting from on-board switching voltage regulators (VRs), to on-chip switching VRs, and finally to networks of distributed on-chip linear VRs. As such, we propose a heterogeneous voltage regulation (HVR) architecture encompassing regulators with complimentary characteristics in response time, size, and efficiency. By exploring the rich heterogeneity and tunability in HVR, we develop systematic workload-aware control policies to adapt heterogeneous VRs with respect to workload change at multiple temporal scales to significantly improve system power efficiency while providing a guarantee for power integrity. The proposed techniques are further supported by hardware-accelerated machine learning prediction of non-uniform spatial workload distributions for more accurate HVR adaptation at fine time granularity. Our evaluations based on the PARSEC benchmark suite show that the proposed adaptive 3-stage HVR reduces the total system energy dissipation by up to 23.9% and 15.7% on average compared with the conventional static two-stage voltage regulation using off- and on-chip switching VRs. Compared with the 3-stage static HVR, our runtime control reduces system energy by up to 17.9% and 12.2% on average. Furthermore, the proposed machine learning prediction offers up to 4.1% reduction of system energy

Improved Accuracy Area Efficient Hybrid CMOS/GaN DC-DC Buck Converterfor High Step-Down Ratio Applications

abstract: Point of Load (POL) DC-DC converters are increasingly used in space applications, data centres, electric vehicles, portable computers and devices and medical electronics. Heavy computing and processing capabilities of the modern devices have ushered the use of higher battery supply voltage to increase power storage. The need to address this consumer experience driven requirement has propelled the evolution of the next generation of small form-factor power converters which can operate with higher step down ratios while supplying heavy continuous load currents without sacrificing efficiency. Constant On-Time (COT) converter topology is capable of achieving stable operation at high conversion ratio with minimum off-chip components and small silicon area. This work proposes a Constant On-Time buck dc-dc converter for a wide dynamic input range and load currents from 100mA to 10A. Accuracy of this ripple based converter is improved by a unique voltage positioning technique which modulates the reference voltage to lower the average ripple profile close to the nominal output. Adaptive On-time block features a transient enhancement scheme to assist in faster voltage droop recovery when the output voltage dips below a defined threshold. UtilizingGallium Nitride (GaN) power switches enable the proposed converter to achieve very high efficiency while using smaller size inductor-capacitor (LC) power-stage. Use of novel Superjunction devices with higher drain-source blocking voltage simplifies the complex driver design and enables faster frequency of operation. It allows 1.8VComplementary Metal-Oxide Semiconductor (CMOS) devices to effectively drive GaNpower FETs which require 5V gate signal swing. The presented controller circuit uses internal ripple generation which reduces reliance on output cap equivalent series resistance (ESR) for loop stability and facilitates ripples reduction at the output. The ripple generation network is designed to provide ai optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.Dissertation/ThesisMasters Thesis Electrical Engineering 201