4,302 research outputs found

    An analysis of the elastic properties of a porous aluminium oxide ïŹlm by means of indentation techniques

    Get PDF
    The elastic modulus of thin ïŹlms can be directly determined by instrumented indentation when the indenter penetration does not exceed a fraction of the ïŹlm thickness, depending on the mechanical properties of both ïŹlm and substrate. When it is not possible, application of models for separating the contribution of the substrate is necessary. In this work, the robustness of several models is analyzed in the case of the elastic modulus determination of a porous aluminium oxide ïŹlm produced by anodization of an aluminium alloy. Instrumented indentation tests employing a Berkovich indenter were performe data nanometric scale, which allowed a direct determination of the ïŹlm elastic modulus, whose value was found to be approximately 11 GPa. However, at a micrometric scale the elastic modulus tends toward the value corresponding to the substrate, of approximately 73 GPa. The objective of the present work is to apply different models for testing their consistency over the complete set of indentation data obtained from both classical tests in microindentation and the continuous stiffness measurement mode in nanoindentation. This approach shows the continuity between the two scales of measurement thus allowing a better representation of the elastic modulus variation between two limits corresponding to the substrate and ïŹlm elastic moduli. Gao's function proved to be the best to represen the elastic modulus variation

    Nano- and micromechanical properties of dentine: Investigation of differences with tooth side

    Get PDF
    NOTICE: this is the author’s version of a work that was accepted for publication in Journal of Biomechanics. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Biomechanics, [VOL 44, (2011)] DOI: 10.1016/j.jbiomech.2011.03.00

    Analysis of indentation size effect in copper and its alloys

    Get PDF
    For describing the indentation size effect (ISE), numerous models, which relate the load or hardness to the indent dimensions, have been proposed. Unfortunately, it is still difficult to associate the different parameters involved in such relationships with physical or mechanical properties of the material. This is an unsolved problem since the ISE can be associated with various causes such as workhardening, roughness, piling-up, sinking-in, indenter tip geometry, surface energy, varying composition and crystal anisotropy. For interpreting the change in hardness with indent size, an original approach is proposed on the basis of composite hardness modelling together with the use of a simple model, which allows the determination of the hardness–depth profile. Applied to copper and copper alloys, it is shown that it is possible to determine the maximum hardness value reached at the outer surface of the material and the distance over which both the ISE and the workhardening take place

    Biomechanical properties of bone in a mouse model of Rett syndrome

    Get PDF
    Rett syndrome (RTT) is an X-linked genetic disorder and a major cause of intellectual disability in girls. Mutations in the methyl-CpG binding protein 2 (<i>MECP2</i>) gene are the primary cause of the disorder. Despite the dominant neurological phenotypes, <i>MECP2</i> is expressed ubiquitously throughout the body and a number of peripheral phenotypes such as scoliosis, reduced bone mineral density and skeletal fractures are also common and important clinical features of the disorder. In order to explore whether MeCP2 protein deficiency results in altered structural and functional properties of bone and to test the potential reversibility of any defects, we have conducted a series of histological, imaging and biomechanical tests of bone in a functional knockout mouse model of RTT. Both hemizygous <i>Mecp2</i><sup>stop/y</sup> male mice in which <i>Mecp2</i> is silenced in all cells and female <i>Mecp2</i><sup>stop/+</sup> mice in which <i>Mecp2</i> is silenced in ~ 50% of cells as a consequence of random X-chromosome inactivation, revealed significant reductions in cortical bone stiffness, microhardness and tensile modulus. Microstructural analysis also revealed alterations in both cortical and cancellous femoral bone between wild-type and MeCP2-deficient mice. Furthermore, unsilencing of <i>Mecp2</i> in adult mice cre-mediated stop cassette deletion resulted in a restoration of biomechanical properties (stiffness, microhardness) towards wild-type levels. These results show that MeCP2-deficiency results in overt, but potentially reversible, alterations in the biomechanical integrity of bone and highlights the importance of targeting skeletal phenotypes in considering the development of pharmacological and gene-based therapies

    High-Impact Mechanical Loading Increases Bone Material Strength in Postmenopausal Women-A 3-Month Intervention Study.

    Get PDF
    Bone adapts to loading in several ways, including redistributing bone mass and altered geometry and microarchitecture. Because of previous methodological limitations, it is not known how the bone material strength is affected by mechanical loading in humans. The aim of this study was to investigate the effect of a 3-month unilateral high-impact exercise program on bone material properties and microarchitecture in healthy postmenopausal women. A total of 20 healthy and inactive postmenopausal women (aged 55.6 ± 2.3 years [mean ± SD]) were included and asked to perform an exercise program of daily one-legged jumps (with incremental number, from 3×10 to 4×20 jumps/d) during 3 months. All participants were asked to register their performed jumps in a structured daily diary. The participants chose one leg as the intervention leg and the other leg was used as control. The operators were blinded to the participant's choice of leg for intervention. The predefined primary outcome was change in bone material strength index (BMSi), measured at the mid tibia with a handheld reference probe indentation instrument (OsteoProbe). Bone microstructure, geometry, and density were measured with high-resolution peripheral quantitative computed tomography (XtremeCT) at the ultradistal and at 14% of the tibia bone length (distal). Differences were analyzed by related samples Wilcoxon signed rank test. The overall compliance to the jumping program was 93.6%. Relative to the control leg, BMSi of the intervention leg increased 7% or 0.89 SD (p = 0.046), but no differences were found for any of the XtremeCT-derived bone parameters. In conclusion, a unilateral high-impact loading program increased BMSi in postmenopausal women rapidly without affecting bone microstructure, geometry, or density, indicating that intense mechanical loading has the ability to rapidly improve bone material properties before changes in bone mass or structure. © 2018 The Authors. Journal of Bone and Mineral Research Published by Wiley Periodicals Inc

    Assessing osteoporosis in the young adult

    Get PDF
    Osteoporosis in the young adult is a relatively rare phenomenon, and its diagnosis needs careful assessment of the affected person. The emphasis in the assessment of bone health is gradually shifting from a simple quantitative assessment of bone mineral density to one that includes bone quality. This may be particularly important in the young adult, where the aetiological cause of osteoporosis may be a primary genetic condition or secondary to another chronic condition

    Depletion of chondrocyte primary cilia reduces the compressive modulus of articular cartilage

    Get PDF
    Primary cilia are slender, microtubule based structures found in the majority of cell types with one cilium per cell. In articular cartilage, primary cilia are required for chondrocyte mechanotransduction and the development of healthy tissue. Loss of primary cilia in Col2aCre;ift88(fl/fl) transgenic mice results in up-regulation of osteoarthritic (OA) markers and development of OA like cartilage with greater thickness and reduced mechanical stiffness. However no previous studies have examined whether loss of primary cilia influences the intrinsic mechanical properties of articular cartilage matrix in the form of the modulus or just the structural properties of the tissue. The present study describes a modified analytical model to derive the viscoelastic moduli based on previous experimental indentation data. Results show that the increased thickness of the articular cartilage in the Col2aCre;ift88(fl/fl) transgenic mice is associated with a reduction in both the instantaneous and equilibrium moduli at indentation strains of greater than 20%. This reveals that the loss of primary cilia causes a significant reduction in the mechanical properties of cartilage particularly in the deeper zones and possibly the underlying bone. This is consistent with histological analysis and confirms the importance of primary cilia in the development of a mechanically functional articular cartilage

    A contact area function for Berkovich nanoindentation : Application to hardness determination of a TiHfCN thin ïŹlm

    Get PDF
    In nanoindentation, especially at very low indenter displacements, the indenter/material contact area must be deïŹned in the best possible way in order to accurately determine the mechanical properties of the material. One of the best methodologies for the computation of the contact area has been proposed by Oliver and Pharr [W.C.Oliver, G.M.Pharr, J.Mater. Res. 7 (1992) 1564], which involves a complex phenomenological area function. Unfortunately, this formulation is only valid when the continuous stiffness measurement mode is employed. For other conditions of indentation, different contact area functions, which take into account the effective truncation length or the radius of the rounded indentertip, as well as some ïŹtting parameters, have been proposed. However, most of these functions require a calibration procedure due to the presence of such parameters. To avoid such a calibration, in the present communication a contact area function only related to the truncation length representative of the indenter tip defect, which can be previously estimated with high resolution microscopy, has been proposed. This model allows the determination of consistent indentation data from indenter displacements of only few nanometers indepth. When this proposed contact area function is applied to the mechanical characterization of a TiHfCN ïŹlm of 2.6 ÎŒm in thickness deposited onto a tool steel substrate, the direct determination of the hardness and elastic modulus of the ïŹlm leads to values of 35.5±2 GPa and 490±50 GPa, respectively

    Development of an advanced dynamic microindentation system to determine local viscoelastic properties of polymers

    Get PDF
    This study presents a microindentation system which allows spatially resolved local as well as bulk viscoelastic material information to be obtained within one instrument. The microindentation method was merged with dynamic mechanical analysis (DMA) for a tungsten cone indenter. Three tungsten cone indenters were investigated: tungsten electrode, tungsten electrode + 2% lanthanum, and tungsten electrode + rare earth elements. Only the tungsten electrode + 2% lanthanum indenter showed the sinusoidal response, and its geometry remained unaffected by the repeated indentations. Complex moduli obtained from dynamic microindentation for high-density polyethylene, polybutylene terephthalate, polycarbonate, and thermoplastic polyurethane are in agreement with the literature. Additionally, by implementing a specially developed x-y-stage, this study showed that dynamic microindentation with a tungsten cone indenter was an adequate method to determine spatially resolved local viscoelastic surface properties. © 2019 by the authors.German Ministry of Education and Research [03FH051PX4]; TREE, Institute of Technology, Resource and Energy-Efficient Engineering Bonn-Rhein-Sieg University of Applied Science
    • 

    corecore