ATSC 3.0 시스템의 2x2 MIMO 방식에 대한 분석

본 논문에서는 ATSC 3.0 시스템의 2x2 multiple-input multiple-output (MIMO) 송신기를 구현하였으며 이에 따른 수신기 구조를 설계하고 성능을 분석한다. ATSC 3.0 시스템의 MIMO 방식은 송신기에서 입력 스트림의 역다중화 (demultiplexing) 및 프리코딩 (precoding)을 통하여 공간 다이버시티 (spatial diversity) 및 공간 다중화 (spatial multiplexing) 이득을 얻을 수 있다. 또한, 전산 실험을 통하여 부호율, 프리코딩, 채널 상관에 따른 성능 결과를 제시한다.|In ATSC 3.0 multiple-input multiple-output (MIMO) system, spatial diversity and multiplexing gains can be obtained using the spatial demultiplexer and MIMO precoder. In this thesis, the transmiting and receiving simulator of 2x2 MIMO system for ATSC 3.0 is implemented and the performance of 2x2 MIMO system is analyzed using the implemented simulator. The computer simulations are performed with various system parameters under severe channel condition. Simulation results show that the MIMO system of ATSC 3.0 can improve the capacity.1. 서 론 2. ATSC 3.0 2x2 MIMO 송신기 2.1 ATSC 3.0 2x2 MIMO 송신기 개요 2.2 2x2 MIMO 역다중화기 2.3 2x2 MIMO 프리코더 2.4 SISO 파일럿 삽입 2.5 2x2 MIMO 파일럿 삽입 3. ATSC 3.0 2x2 MIMO 수신기 3.1 ATSC 3.0 2x2 MIMO 수신기 개요 3.2 2x2 MIMO 채널 3.3 2x2 MIMO 채널 추정 3.4 LLR 계산 4. 전산 실험 결과 5. 결론Maste

MIMO for ATSC 3.0

"(c) 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.")This paper provides an overview of the optional MIMO (Multiple-Input Multiple-Output) antenna scheme adopted in ATSC 3.0 to improve robustness or increase capacity via additional spatial diversity and multiplexing by sending two data streams in a single radio frequency channel. Although it is not directly specified, it is expected in practice to use cross-polarized 2x2 MIMO (i.e., horizontal and vertical polarization) to retain multiplexing capabilities in line-of-sight conditions. MIMO allows overcoming the channel capacity limit of single antenna wireless communications in a given channel bandwidth without any increase in the total transmission power. But in the U.S. MIMO can actually provide a larger comparative gain because it would be allowed to increase the total transmit power, by transmitting the nominal transmit power in each polarization. Hence, in addition to the MIMO gains (array, diversity and spatial multiplexing), MIMO could exploit an additional 3 dB power gain. The MIMO scheme adopted in ATSC 3.0 re-uses the SISO (Single-Input Single-Output) antenna baseline constellations, and hence it introduces the use of MIMO with non-uniform constellations.Gómez Barquero, D.; Vargas, D.; Fuentes Muela, M.; Klenner, P.; Moon, S.; Choi, J.; Schneider, D.... (2016). MIMO for ATSC 3.0. IEEE Transactions on Broadcasting. 62(1):298-305. doi:10.1109/TBC.2015.2505399S29830562

MIMO Scattered Pilot Performance and Optimization for ATSC 3.0

(c) 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this[EN] ATSC 3.0 is the latest digital terrestrial television (DTT) standard, and it allows a higher spectral efficiency and/or a transmission robustness with multiple-input multiple-output (MIMO) technology compared to existing DTT standards. Regarding MIMO channel estimation, two pilot encoding algorithms known as Walsh-Hadamard encoding and Null Pilot encoding are possible in ATSC 3.0. The two MIMO pilot algorithms are standardized so as to have the same pilot positions and the same pilot boosting as single-input single-output, and the optimum pilot configuration has not been fully evaluated for MIMO. This paper focuses on the performance evaluation and optimization of the pilot boosting and the pilot patterns for two MIMO pilot encoding algorithms in ATSC 3.0 using physical layer simulations. This paper provides a great benefit to broadcasters to select the MIMO pilot configuration including pilot boosting, pilot pattern, and pilot encoding algorithm that better suits their service requirements. Several channel interpolation algorithms have been taken into account as a typical receiver implementation in both fixed SFN reception and mobile reception.This work was supported in part by the Ministry of Economy and Competitiveness of Spain under Grant TEC2014-56483-R, and in part by the European FEDER Fund.Shitomi, T.; Garro, E.; Murayama, K.; Gomez-Barquero, D. (2018). MIMO Scattered Pilot Performance and Optimization for ATSC 3.0. IEEE Transactions on Broadcasting. 64(2):188-200. https://doi.org/10.1109/TBC.2017.2755262S18820064

Performance evaluation of MIMO channel estimation for ATSC 3.0

[Otros] ATSC 3.0, the latest Digital Terrestrial Television (DTT) standard, allows a higher spectral efficiency and/or a transmission robustness with Multiple-Input Multiple-Output (MIMO) technology compared to existing single-antenna DTT networks. Regarding MIMO channel estimation, two pilot encoding algorithms known as Walsh-Hadamard encoding and Null pilot encoding are possible in ATSC 3.0. The two MIMO pilot algorithms are standardized so as to have the same pilot positions and the same pilot boosting as SISO, but the performance has not been evaluated. This paper focuses on the performance evaluation of the two MIMO pilot encoding algorithms in ATSC 3.0 using physical layer simulations. Results can be used as guidelines or recommended practices to broadcasters to select the MIMO pilot encoding algorithm that better suits their service requirments. Several channel estimation algorithms have been evaluated in both mobile and fixed reception conditions. The simulation results show that Null pilot encoding provides slightly better performance than WalshHadamard encoding for fixed reception but worse performance for mobile reception, especially at high signal-to-noise ratios.This work was partially supported by the Ministerio de Educacion y Ciencia, Spain (TEC2014-56483-R), co-funded by European FEDER funds.Shitomi, T.; Garro, E.; Murayama, K.; Gomez-Barquero, D. (2017). Performance evaluation of MIMO channel estimation for ATSC 3.0. IEEE. 1-5. https://doi.org/10.1109/BMSB.2017.7986237S1

An Overview of the ATSC 3.0 Physical Layer Specification

"(c) 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.")This paper provides an overview of the physical layer specification of Advanced Television Systems Committee (ATSC) 3.0, the next-generation digital terrestrial broadcasting standard. ATSC 3.0 does not have any backwards-compatibility constraint with existing ATSC standards, and it uses orthogonal frequency division multiplexing-based waveforms along with powerful low-density parity check (LDPC) forward error correction codes similar to existing state-of-the-art. However, it introduces many new technological features such as 2-D non-uniform constellations, improved and ultra-robust LDPC codes, power-based layered division multiplexing to efficiently provide mobile and fixed services in the same radio frequency (RF) channel, as well as a novel frequency pre-distortion multiple-input single-output antenna scheme. ATSC 3.0 also allows bonding of two RF channels to increase the service peak data rate and to exploit inter-RF channel frequency diversity, and to employ dual-polarized multiple-input multiple-output antenna system. Furthermore, ATSC 3.0 provides great flexibility in terms of configuration parameters (e.g., 12 coding rates, 6 modulation orders, 16 pilot patterns, 12 guard intervals, and 2 time interleavers), and also a very flexible data multiplexing scheme using time, frequency, and power dimensions. As a consequence, ATSC 3.0 not only improves the spectral efficiency and robustness well beyond the first generation ATSC broadcast television standard, but also it is positioned to become the reference terrestrial broadcasting technology worldwide due to its unprecedented performance and flexibility. Another key aspect of ATSC 3.0 is its extensible signaling, which will allow including new technologies in the future without disrupting ATSC 3.0 services. This paper provides an overview of the physical layer technologies of ATSC 3.0, covering the ATSC A/321 standard that describes the so-called bootstrap, which is the universal entry point to an ATSC 3.0 signal, and the ATSC A/322 standard that describes the physical layer downlink signals after the bootstrap. A summary comparison between ATSC 3.0 and DVB-T2 is also provided.Fay, L.; Michael, L.; Gómez Barquero, D.; Ammar, N.; Caldwell, MW. (2016). An Overview of the ATSC 3.0 Physical Layer Specification. IEEE Transactions on Broadcasting. 62(1):159-171. doi:10.1109/TBC.2015.2505417S15917162

ATSC 3.0 Next Generation Digital TV Standard - An Overview and Preview of the Issue

"(c) 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works."The Advanced Television Committee (ATSC) has been working on the next generation broadcast television system, known as ATSC 3.0, to replace the first-generation (ATSC 1.0) A/53 standard, the basic component technologies of which have been in use for 20 years.Chernock, R.; Gómez Barquero, D.; Whitaker, J.; Park, S.; Wu, Y. (2016). ATSC 3.0 Next Generation Digital TV Standard - An Overview and Preview of the Issue. IEEE Transactions on Broadcasting. 62(1):154-158. doi:10.1109/TBC.2016.2515542S15415862

Advanced Layered Divsion Multiplexing Technologies for Next-Gen Broadcast

Tesis por compendioDesde comienzos del siglo XXI, los sistemas de radiodifusión terrestre han sido culpados de un uso ineficiente del espectro asignado. Para aumentar la eficiencia espectral, los organismos de estandarización de TV digital comenzaron a desarrollar la evolución técnica de los sistemas de TDT de primera generación. Entre otros, uno de los objetivos principales de los sistemas de TDT de próxima generación (DVB-T2 y ATSC 3.0) es proporcionar simultáneamente servicios de TV a dispositivos móviles y fijos. El principal inconveniente de esta entrega simultánea son los diferentes requisitos de cada condición de recepción. Para abordar estas limitaciones, se han considerado diferentes técnicas de multiplexación. Mientras que DVB-T2 acomete la entrega simultánea de los dos servicios mediante TDM, ATSC 3.0 adoptó la Multiplexación por División en Capas (LDM). LDM puede superar a TDM y a FDM al aprovechar la relación de Protección de Error Desigual (UEP), ya que ambos servicios, llamados capas, utilizan todos los recursos de frecuencia y tiempo con diferentes niveles de potencia. En el lado del receptor, se distinguen dos implementaciones, de acuerdo con la capa a decodificar. Los receptores móviles solo están destinados a obtener la capa superior, conocida como Core Layer (CL). Para no aumentar su complejidad en comparación con los receptores de capa única, la capa inferior, conocida como Enhanced Layer (EL), es tratada como un ruido adicional en la decodificación. Los receptores fijos aumentan su complejidad, ya que deben realizar un proceso de Cancelación de Interferencia (SIC) sobre la CL para obtener la EL. Para limitar la complejidad adicional de los receptores fijos, las capas de LDM en ATSC 3.0 están configuradas con diferentes capacidades de corrección, pero comparten el resto de bloques de la capa física, incluido el TIL, el PP, el tamaño de FFT, y el GI. Esta disertación investiga tecnologías avanzadas para optimizar el rendimiento de LDM. Primero se propone una optimización del proceso de demapeo para las dos capas de LDM. El algoritmo propuesto logra un aumento de capacidad, al tener en cuenta la forma de la EL en el proceso de demapeo de la CL. Sin embargo, el número de distancias Euclidianas a computar puede aumentar significativamente, conduciendo no solo a receptores fijos más complejos, sino también a receptores móviles más complejos. A continuación, se determina la configuración de piloto ATSC 3.0 más adecuada para LDM. Teniendo en cuenta que las dos capas comparten el mismo PP, surge una contrapartida entre la densidad de pilotos (CL) y la redundancia sobre los datos (EL). A partir de los resultados de rendimiento, se recomienda el uso de un PP no muy denso, ya que ya han sido diseñados para hacer frente a ecos largos y altas velocidades. La amplitud piloto óptima depende del estimador de canal en los receptores (ej., se recomienda la amplitud mínima para una implementación Wiener, mientras que la máxima para una implementación FFT). También se investiga la potencial transmisión conjunta de LDM con tres tecnologías avanzadas adoptadas en ATSC 3.0: las tecnologías de agregación MultiRF, los esquemas de MISO distribuido y los de MIMO colocalizado. Se estudian los potenciales casos de uso, los aspectos de implementación del transmisor y el receptor, y las ganancias de rendimiento de las configuraciones conjuntas para las dos capas de LDM. Las restricciones adicionales de combinar LDM con las tecnologías avanzadas se consideran admisibles, ya que las mayores demandas ya están contempladas en ATSC 3.0 (ej., una segunda cadena de recepción). Se obtienen ganancias significativas en condiciones de recepción peatonal gracias a la diversidad en frecuencia proporcionada por las tecnologías MultiRF. La conjunción de LDM con esquemas de MISO proporciona ganancias de rendimiento significativas en redes SFN para la capa fija con el esquema de Alamouti.Since the beginning of the 21st century, terrestrial broadcasting systems have been blamed of an inefficient use of the allocated spectrum. To increase the spectral efficiency, digital television Standards Developing Organizations settled to develop the technical evolution of the first-generation DTT systems. Among others, a primary goal of next-generation DTT systems (DVB-T2 and ATSC 3.0) is to simultaneously provide TV services to mobile and fixed devices. The major drawback of this simultaneous delivery is the different requirement of each reception condition. To address these constraints different multiplexing techniques have been considered. While DVB-T2 fulfilled the simultaneous delivery of the two services by TDM, ATSC 3.0 adopted the LDM technology. LDM can outperform TDM and FDM by taking advantage of the UEP ratio, as both services, namely layers, utilize all the frequency and time resources with different power levels. At receiver side, two implementations are distinguished, according to the intended layer. Mobile receivers are only intended to obtain the upper layer, known as CL. In order not to increase their complexity compared to single layer receivers, the lower layer, known as EL is treated as an additional noise on the CL decoding. Fixed receivers, increase their complexity, as they should performed a SIC process on the CL for getting the EL. To limit the additional complexity of fixed receivers, the LDM layers in ATSC 3.0 are configured with different error correction capabilities, but share the rest of physical layer parameters, including the TIL, the PP, the FFT size, and the GI. This dissertation investigates advanced technologies to optimize the LDM performance. A demapping optimization for the two LDM layers is first proposed. A capacity increase is achieved by the proposed algorithm, which takes into account the underlying layer shape in the demapping process. Nevertheless, the number of Euclidean distances to be computed can be significantly increased, contributing to not only more complex fixed receivers, but also more complex mobile receivers. Next, the most suitable ATSC 3.0 pilot configuration for LDM is determined. Considering the two layers share the same PP a trade-off between pilot density (CL) and data overhead (EL) arises. From the performance results, it is recommended the use of a not very dense PP, as they have been already designed to cope with long echoes and high speeds. The optimum pilot amplitude depends on the channel estimator at receivers (e.g. the minimum amplitude is recommended for a Wiener implementation, while the maximum for a FFT implementation). The potential combination of LDM with three advanced technologies that have been adopted in ATSC 3.0 is also investigated: MultiRF technologies, distributed MISO schemes, and co-located MIMO schemes. The potential use cases, the transmitter and receiver implementations, and the performance gains of the joint configurations are studied for the two LDM layers. The additional constraints of combining LDM with the advanced technologies is considered admissible, as the greatest demands (e.g. a second receiving chain) are already contemplated in ATSC 3.0. Significant gains are found for the mobile layer at pedestrian reception conditions thanks to the frequency diversity provided by MultiRF technologies. The conjunction of LDM with distributed MISO schemes provides significant performance gains on SFNs for the fixed layer with Alamouti scheme. Last, considering the complexity in the mobile receivers and the CL performance, the recommended joint configuration is MISO in the CL and MIMO in the EL.Des de començaments del segle XXI, els sistemes de radiodifusió terrestre han sigut culpats d'un ús ineficient de l'espectre assignat. Per a augmentar l'eficiència espectral, els organismes d'estandardització de TV digital van començar a desenvolupar l'evolució tècnica dels sistemes de TDT de primera generació. Entre altres, un dels objectius principals dels sistemes de TDT de pròxima generació (DVB-T2 i el ATSC 3.0) és proporcionar simultàniament serveis de TV a dispositius mòbils i fixos. El principal inconvenient d'aquest lliurament simultani són els diferents requisits de cada condició de recepció. Per a abordar aquestes limitacions, s'han considerat diferents tècniques de multiplexació. Mentre que DVB-T2 escomet el lliurament simultani dels dos serveis mitjançant TDM, ATSC 3.0 va adoptar la Multiplexació per Divisió en Capes (LDM). LDM pot superar a TDM i a FDM en aprofitar la relació de Protecció d'Error Desigual (UEP), ja que tots dos serveis, cridats capes, utilitzen tots els recursos de freqüència i temps amb diferents nivells de potència. En el costat del receptor, es distingeixen dues implementacions, d'acord amb la capa a decodificar. Els receptors mòbils solament estan destinats a obtenir la capa superior, coneguda com Core Layer (CL). Per a no augmentar la seua complexitat en comparació amb els receptors de capa única, la capa inferior, coneguda com Enhanced Layer (EL), és tractada com un soroll addicional en la decodificació. Els receptors fixos augmenten la seua complexitat, ja que han de realitzar un procés de Cancel·lació d'Interferència (SIC) sobre la CL per a obtenir l'EL. Per a limitar la complexitat addicional dels receptors fixos, les capes de LDM en ATSC 3.0 estan configurades amb diferents capacitats de correcció, però comparteixen la resta de blocs de la capa física, inclòs el TIL, el PP, la grandària de FFT i el GI. Aquesta dissertació investiga tecnologies avançades per a optimitzar el rendiment de LDM. Primer es proposa una optimització del procés de demapeo per a les dues capes de LDM. L'algoritme proposat aconsegueix un augment de capacitat, en tenir en compte la forma de l'EL en el procés de demapeo de la CL. No obstant açò, el nombre de distàncies Euclidianes a computar pot augmentar significativament, conduint NO sols a receptors fixos més complexos, sinó també a receptors mòbils més complexos. A continuació, es determina la configuració de pilot ATSC 3.0 més adequada per a LDM. Tenint en compte que les dues capes comparteixen el mateix PP, es produeix una contrapartida entre la densitat de pilots (CL) i la redundància sobre les dades (EL). A partir dels resultats de rendiment, es recomana l'ús d'un PP no gaire dens, ja que ja han sigut dissenyats per a fer front a ecos llargs i altes velocitats. L'amplitud pilot òptima depèn de l'estimador de canal en els receptors (ex., es recomana l'amplitud mínima per a una implementació Wiener, mentre que la màxima per a una implementació FFT). També s'investiga la potencial transmissió conjunta de LDM amb tres tecnologies avançades adoptades en ATSC 3.0: les tecnologies d'agregació de MultiRF, els esquemes de MISO distribuït i els de MIMO colocalitzat. S'estudien els potencials casos d'ús, els principals aspectes d'implementació del transmissor i el receptor, i els guanys de rendiment de les configuracions conjuntes per a les dues capes de LDM. Les restriccions addicionals de combinar LDM amb les tecnologies avançades es consideren admissibles, ja que les majors demandes ja estan contemplades en ATSC 3.0 (ex., una segona cadena de recepció). S'obtenen guanys significatius per a la capa mòbil en condicions de recepció per als vianants gràcies a la diversitat en freqüència proporcionada per les tecnologies MultiRF. La conjunció de LDM amb esquemes MISO distribuïts proporciona guanys de rendiment significatius en xarxes SFN per a la capa fixa amb l'esquema d'Alamouti.Garro Crevillén, E. (2018). Advanced Layered Divsion Multiplexing Technologies for Next-Gen Broadcast [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/105559TESISCompendi

Physical Layer Performance Evaluation of LTE-Advanced Pro Broadcast and ATSC 3.0 Systems

This work provides a detailed performance analysis of the physical layer of two state-of-the-art point-to-multipoint (PTM) technologies: evolved Multimedia Broadcast Multicast Services (eMBMS) and Advanced Television Systems Committee - Third Generation (ATSC 3.0). The performance of these technologies is evaluated and compared using link-level simulations, considering relevant identified scenarios. A selection of Key Performance Indicators (KPI) for the International Mobile Telecommunications 2020 (IMT-2020) evaluation process has been considered. Representative use cases are also aligned to the test environments as defined in the IMT-2020 evaluation guidelines. It is observed that ATSC 3.0 outperforms both eMBMS solutions, i.e. MBMS over Single Frequency Networks (MBSFN) and Single-Cell PTM (SC-PTM) in terms of spectral efficiency, peak data rate and mobility, among others. This performance evaluation serves as a benchmark for comparison with a potential 5G PTM solution

Physical Layer Time Interleaving for the ATSC 3.0 System

"(c) 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.")This paper presents optimized time interleaving which has been adopted for the Advanced Television System Committee 3.0 system as a physical layer tool to mitigate the effects of burst errors. The adopted time interleaver (TI) is very flexible and can have different configurations according to the number of physical layer pipes (PLPs) and service type, i.e., fixed, portable, and mobile. Notably, for single-PLP mode a sheer convolutional TI (CTI) is used, whereas for the multiple-PLP mode a hybrid TI (HTI) composed of cell interleaver, twisted block interleaver, and a convolutional delay-line is used. Optionally, the CTI and the HTI can be used in conjunction with extended time interleaving and a cell interleaver (only for HTI) to further improve robustness over long burst error lengths at the expense of latency.Klenner, P.; Baek, J.; Loghin, NS.; Gómez Barquero, D.; Ko, W. (2016). Physical Layer Time Interleaving for the ATSC 3.0 System. IEEE Transactions on Broadcasting. 62(1):253-262. doi:10.1109/TBC.2015.2505410S25326262

Transmit and Receive Signal Processing for MIMO Terrestrial Broadcast Systems

[EN] Multiple-Input Multiple-Output (MIMO) technology in Digital Terrestrial Television (DTT) networks has the potential to increase the spectral efficiency and improve network coverage to cope with the competition of limited spectrum use (e.g., assignment of digital dividend and spectrum demands of mobile broadband), the appearance of new high data rate services (e.g., ultra-high definition TV - UHDTV), and the ubiquity of the content (e.g., fixed, portable, and mobile). It is widely recognised that MIMO can provide multiple benefits such as additional receive power due to array gain, higher resilience against signal outages due to spatial diversity, and higher data rates due to the spatial multiplexing gain of the MIMO channel. These benefits can be achieved without additional transmit power nor additional bandwidth, but normally come at the expense of a higher system complexity at the transmitter and receiver ends. The final system performance gains due to the use of MIMO directly depend on physical characteristics of the propagation environment such as spatial correlation, antenna orientation, and/or power imbalances experienced at the transmit aerials. Additionally, due to complexity constraints and finite-precision arithmetic at the receivers, it is crucial for the overall system performance to carefully design specific signal processing algorithms. This dissertation focuses on transmit and received signal processing for DTT systems using MIMO-BICM (Bit-Interleaved Coded Modulation) without feedback channel to the transmitter from the receiver terminals. At the transmitter side, this thesis presents investigations on MIMO precoding in DTT systems to overcome system degradations due to different channel conditions. At the receiver side, the focus is given on design and evaluation of practical MIMO-BICM receivers based on quantized information and its impact in both the in-chip memory size and system performance. These investigations are carried within the standardization process of DVB-NGH (Digital Video Broadcasting - Next Generation Handheld) the handheld evolution of DVB-T2 (Terrestrial - Second Generation), and ATSC 3.0 (Advanced Television Systems Committee - Third Generation), which incorporate MIMO-BICM as key technology to overcome the Shannon limit of single antenna communications. Nonetheless, this dissertation employs a generic approach in the design, analysis and evaluations, hence, the results and ideas can be applied to other wireless broadcast communication systems using MIMO-BICM.[ES] La tecnología de múltiples entradas y múltiples salidas (MIMO) en redes de Televisión Digital Terrestre (TDT) tiene el potencial de incrementar la eficiencia espectral y mejorar la cobertura de red para afrontar las demandas de uso del escaso espectro electromagnético (e.g., designación del dividendo digital y la demanda de espectro por parte de las redes de comunicaciones móviles), la aparición de nuevos contenidos de alta tasa de datos (e.g., ultra-high definition TV - UHDTV) y la ubicuidad del contenido (e.g., fijo, portable y móvil). Es ampliamente reconocido que MIMO puede proporcionar múltiples beneficios como: potencia recibida adicional gracias a las ganancias de array, mayor robustez contra desvanecimientos de la señal gracias a la diversidad espacial y mayores tasas de transmisión gracias a la ganancia por multiplexado del canal MIMO. Estos beneficios se pueden conseguir sin incrementar la potencia transmitida ni el ancho de banda, pero normalmente se obtienen a expensas de una mayor complejidad del sistema tanto en el transmisor como en el receptor. Las ganancias de rendimiento finales debido al uso de MIMO dependen directamente de las características físicas del entorno de propagación como: la correlación entre los canales espaciales, la orientación de las antenas y/o los desbalances de potencia sufridos en las antenas transmisoras. Adicionalmente, debido a restricciones en la complejidad y aritmética de precisión finita en los receptores, es fundamental para el rendimiento global del sistema un diseño cuidadoso de algoritmos específicos de procesado de señal. Esta tesis doctoral se centra en el procesado de señal, tanto en el transmisor como en el receptor, para sistemas TDT que implementan MIMO-BICM (Bit-Interleaved Coded Modulation) sin canal de retorno hacia el transmisor desde los receptores. En el transmisor esta tesis presenta investigaciones en precoding MIMO en sistemas TDT para superar las degradaciones del sistema debidas a diferentes condiciones del canal. En el receptor se presta especial atención al diseño y evaluación de receptores prácticos MIMO-BICM basados en información cuantificada y a su impacto tanto en la memoria del chip como en el rendimiento del sistema. Estas investigaciones se llevan a cabo en el contexto de estandarización de DVB-NGH (Digital Video Broadcasting - Next Generation Handheld), la evolución portátil de DVB-T2 (Second Generation Terrestrial), y ATSC 3.0 (Advanced Television Systems Commitee - Third Generation) que incorporan MIMO-BICM como clave tecnológica para superar el límite de Shannon para comunicaciones con una única antena. No obstante, esta tesis doctoral emplea un método genérico tanto para el diseño, análisis y evaluación, por lo que los resultados e ideas pueden ser aplicados a otros sistemas de comunicación inalámbricos que empleen MIMO-BICM.[CA] La tecnologia de múltiples entrades i múltiples eixides (MIMO) en xarxes de Televisió Digital Terrestre (TDT) té el potencial d'incrementar l'eficiència espectral i millorar la cobertura de xarxa per a afrontar les demandes d'ús de l'escàs espectre electromagnètic (e.g., designació del dividend digital i la demanda d'espectre per part de les xarxes de comunicacions mòbils), l'aparició de nous continguts d'alta taxa de dades (e.g., ultra-high deffinition TV - UHDTV) i la ubiqüitat del contingut (e.g., fix, portàtil i mòbil). És àmpliament reconegut que MIMO pot proporcionar múltiples beneficis com: potència rebuda addicional gràcies als guanys de array, major robustesa contra esvaïments del senyal gràcies a la diversitat espacial i majors taxes de transmissió gràcies al guany per multiplexat del canal MIMO. Aquests beneficis es poden aconseguir sense incrementar la potència transmesa ni l'ample de banda, però normalment s'obtenen a costa d'una major complexitat del sistema tant en el transmissor com en el receptor. Els guanys de rendiment finals a causa de l'ús de MIMO depenen directament de les característiques físiques de l'entorn de propagació com: la correlació entre els canals espacials, l'orientació de les antenes, i/o els desequilibris de potència patits en les antenes transmissores. Addicionalment, a causa de restriccions en la complexitat i aritmètica de precisió finita en els receptors, és fonamental per al rendiment global del sistema un disseny acurat d'algorismes específics de processament de senyal. Aquesta tesi doctoral se centra en el processament de senyal tant en el transmissor com en el receptor per a sistemes TDT que implementen MIMO-BICM (Bit-Interleaved Coded Modulation) sense canal de tornada cap al transmissor des dels receptors. En el transmissor aquesta tesi presenta recerques en precoding MIMO en sistemes TDT per a superar les degradacions del sistema degudes a diferents condicions del canal. En el receptor es presta especial atenció al disseny i avaluació de receptors pràctics MIMO-BICM basats en informació quantificada i al seu impacte tant en la memòria del xip com en el rendiment del sistema. Aquestes recerques es duen a terme en el context d'estandardització de DVB-NGH (Digital Video Broadcasting - Next Generation Handheld), l'evolució portàtil de DVB-T2 (Second Generation Terrestrial), i ATSC 3.0 (Advanced Television Systems Commitee - Third Generation) que incorporen MIMO-BICM com a clau tecnològica per a superar el límit de Shannon per a comunicacions amb una única antena. No obstant açò, aquesta tesi doctoral empra un mètode genèric tant per al disseny, anàlisi i avaluació, per la qual cosa els resultats i idees poden ser aplicats a altres sistemes de comunicació sense fils que empren MIMO-BICM.Vargas Paredero, DE. (2016). Transmit and Receive Signal Processing for MIMO Terrestrial Broadcast Systems [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/66081TESISPremiad