Investigation of methods for data communication and power delivery through metals

PhD ThesisThe retrieval of data from a sensor, enclosed by a metallic structure, such as a naval vessel, pipeline or nuclear flask is often very challenging. To maintain structural integrity it is not desirable to penetrate the wall of the structure, preventing any hard-wired solution. Furthermore, the conductive nature of the structure prevents the use of radio communications. Applications involving sealed containers also have a requirement for power delivery, as the periodic changing of batteries is not possible. Ultrasound has previously been identified as an attractive approach but there are two key challenges: efficient/reliable ultrasonic transduction and a method of overcoming the inherent multipath distortion resulting from boundary reflections. Previous studies have utilised piezoelectric contact transducers, however, they are impractical due to their reliance on coupling, i.e. the bond between the transducer and the metal surface, which leads to concerns over long term reliability. A non-contact transducer overcomes this key drawback, thus highlighting the electromagnetic acoustic transducer (EMAT) as a favourable alternative. This thesis presents the design and testing of an EMAT with appropriate characteristics for through-metal data communications. A low cost, low power data transmission scheme is presented for overcoming acoustic multipath based on pulse position modulation (PPM). Due to the necessary guard time, the data rate is limited to 50kbps. A second solution is presented employing continuous wave, Quadrature phase shift keying (QPSK) modulation, allowing data rates in excess of 1Mbps to be achieved. Equalisation is required to avoid intersymbol interference (ISI) and a decision feedback equaliser (DFE) is shown to be adept at mitigating this effect. The relatively low efficiency of an EMAT makes it unsuitable for power delivery, consequently, an alternative non-contact approach, utilising inductive coupling, is explored. Power transfer efficiency of ≈ 4% is shown to be achievable through 20mm thick stainless steel.ICS department of BAE Systems Submarine Solutions, EPSR

Intra-Body Communications for Nervous System Applications: Current Technologies and Future Directions

The Internet of Medical Things (IoMT) paradigm will enable next generation healthcare by enhancing human abilities, supporting continuous body monitoring and restoring lost physiological functions due to serious impairments. This paper presents intra-body communication solutions that interconnect implantable devices for application to the nervous system, challenging the specific features of the complex intra-body scenario. The presented approaches include both speculative and implementative methods, ranging from neural signal transmission to testbeds, to be applied to specific neural diseases therapies. Also future directions in this research area are considered to overcome the existing technical challenges mainly associated with miniaturization, power supply, and multi-scale communications.Comment: https://www.sciencedirect.com/science/article/pii/S138912862300163

Proceedings of Abstracts Engineering and Computer Science Research Conference 2019

© 2019 The Author(s). This is an open-access work distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited. For further details please see https://creativecommons.org/licenses/by/4.0/. Note: Keynote: Fluorescence visualisation to evaluate effectiveness of personal protective equipment for infection control is © 2019 Crown copyright and so is licensed under the Open Government Licence v3.0. Under this licence users are permitted to copy, publish, distribute and transmit the Information; adapt the Information; exploit the Information commercially and non-commercially for example, by combining it with other Information, or by including it in your own product or application. Where you do any of the above you must acknowledge the source of the Information in your product or application by including or linking to any attribution statement specified by the Information Provider(s) and, where possible, provide a link to this licence: http://www.nationalarchives.gov.uk/doc/open-government-licence/version/3/This book is the record of abstracts submitted and accepted for presentation at the Inaugural Engineering and Computer Science Research Conference held 17th April 2019 at the University of Hertfordshire, Hatfield, UK. This conference is a local event aiming at bringing together the research students, staff and eminent external guests to celebrate Engineering and Computer Science Research at the University of Hertfordshire. The ECS Research Conference aims to showcase the broad landscape of research taking place in the School of Engineering and Computer Science. The 2019 conference was articulated around three topical cross-disciplinary themes: Make and Preserve the Future; Connect the People and Cities; and Protect and Care

A Three – tier bio-implantable sensor monitoring and communications platform

One major hindrance to the advent of novel bio-implantable sensor technologies is the need for a reliable power source and data communications platform capable of continuously, remotely, and wirelessly monitoring deeply implantable biomedical devices. This research proposes the feasibility and potential of combining well established, ‘human-friendly' inductive and ultrasonic technologies to produce a proof-of-concept, generic, multi-tier power transfer and data communication platform suitable for low-power, periodically-activated implantable analogue bio-sensors. In the inductive sub-system presented, 5 W of power is transferred across a 10 mm gap between a single pair of 39 mm (primary) and 33 mm (secondary) circular printed spiral coils (PSCs). These are printed using an 8000 dpi resolution photoplotter and fabricated on PCB by wet-etching, to the maximum permissible density. Our ultrasonic sub-system, consisting of a single pair of Pz21 (transmitter) and Pz26 (receiver) piezoelectric PZT ceramic discs driven by low-frequency, radial/planar excitation (-31 mode), without acoustic matching layers, is also reported here for the first time. The discs are characterised by propagation tank test and directly driven by the inductively coupled power to deliver 29 μW to a receiver (implant) employing a low voltage start-up IC positioned 70 mm deep within a homogeneous liquid phantom. No batteries are used. The deep implant is thus intermittently powered every 800 ms to charge a capacitor which enables its microcontroller, operating with a 500 kHz clock, to transmit a single nibble (4 bits) of digitized sensed data over a period of ~18 ms from deep within the phantom, to the outside world. A power transfer efficiency of 83% using our prototype CMOS logic-gate IC driver is reported for the inductively coupled part of the system. Overall prototype system power consumption is 2.3 W with a total power transfer efficiency of 1% achieved across the tiers

Monitoring of the central blood pressure waveform via a conformal ultrasonic device.

Continuous monitoring of the central-blood-pressure waveform from deeply embedded vessels, such as the carotid artery and jugular vein, has clinical value for the prediction of all-cause cardiovascular mortality. However, existing non-invasive approaches, including photoplethysmography and tonometry, only enable access to the superficial peripheral vasculature. Although current ultrasonic technologies allow non-invasive deep-tissue observation, unstable coupling with the tissue surface resulting from the bulkiness and rigidity of conventional ultrasound probes introduces usability constraints. Here, we describe the design and operation of an ultrasonic device that is conformal to the skin and capable of capturing blood-pressure waveforms at deeply embedded arterial and venous sites. The wearable device is ultrathin (240 μm) and stretchable (with strains up to 60%), and enables the non-invasive, continuous and accurate monitoring of cardiovascular events from multiple body locations, which should facilitate its use in a variety of clinical environments

Fine recycled concrete aggregate as a material replacement in concrete production

As a fast and rapid growing nation, Malaysia undergoes a lot of development especially in construction field. Most of the building nowadays are being made mainly using concrete as it provides many favorable features such as satisfactory compressive strength, durability, availability, versatility and cost effectiveness. However, in pursuing the development era, sometimes the authorities overlooked about the construction and demolition (C&D) waste that had been created along the development progress. Construction and demolition waste is becoming a vital issue especially to the environmental aspect in many large cities in the world (Chen et al., 2002). Shen [1] describe C&D waste as the waste which generated from renovation, site clearing, demolition, construction, roadwork, land excavation and civil and building construction. Construction and Demolition (C&D) waste constitutes a major portion of total solid waste production in the world, and most of it is used in landfills .

Wireless body sensor networks for health-monitoring applications

This is an author-created, un-copyedited version of an article accepted for publication in Physiological Measurement. The publisher is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at http://dx.doi.org/10.1088/0967-3334/29/11/R01