Low-power current-mode ADC for CMOS sensor IC

A low-energy current-mode algorithmic pipelined ADC targeted for use in distributed sensor networks is presented. The individual nodes combine sensing, computation and communications into an extremely small volume. The nodes operate with very low duty cycle due to limited energy. Ideally these sensor networks will be massive in size and dense in order to promote redundancy. In addition the networks will be collectively intelligent and adaptive. To achieve these goals, distributed sensor networks will require very small,inexpensive nodes that run for long periods of time on very little energy. One component of such network nodes is an A/D converter. An ADC acts as a crucial interface between the sensed environment and the sensor network as a whole. The work presented here focuses on moderate resolution, and moderate speed, but ultra-low-power ADCs. The 6 bit current-mode algorithmic pipelined ADC reported here consumes 8 pJ/bit samples at 0.65V supply and 130 kS/s. The current was chosen as the information carrying quantity instead of voltage as it is more favorable for low-voltage and low-power applications. The reference current chosen was 150nA. All the blocks are using transistors operating in subthreshold or weak inversion region of operation, to work in low-voltage and low current supply. The DNL and INL plots are given in simulation results section. The area of the overall ADC was 0.046 mm2 only

Design of pixel-level ADCs for energy-sensitive hybrid pixel detectors

Single-photon counting hybrid pixel detectors have shown\ud to be a valid alternative to other types of X-ray imaging\ud devices due to their high sensitivity, low noise, linear behavior\ud and wide dynamic range. One important advantage of these\ud devices is the fact that detector and readout electronics are\ud manufactured separately. This allows the use of industrial\ud state-of-the-art CMOS processes to make the readout\ud electronics, combined with a free choice of detector material\ud (high resistivity Silicon, GaAs or other). By measuring not\ud only the number of X-ray photons but also their energies (or\ud wavelengths), the information content of the image increases,\ud given the same X-ray dose. We have studied several\ud possibilities of adding energy sensitivity to the single photon\ud counting capability of hybrid pixel detectors, by means of\ud pixel-level analog-to-digital converters. We show the results of\ud simulating different kinds of analog-to-digital converters in\ud terms of power, area and speed

Towards a single-photon energy-sensitive pixel readout chip: pixel level ADCs and digital readout circuitry

Unlike conventional CMOS imaging, a single\ud photon imager detects each individual photon impinging on\ud a detector, accumulating the number of photons during a\ud certain time window and not the charge generated by the all\ud the photons hitting the detector during said time window.\ud The latest developments in the semiconductor industry\ud are allowing faster and more complex chips to be designed\ud and manufactured. With these developments in mind we are\ud working towards the next step in single photon X-ray imaging:\ud energy sensitive pixel readout chips. The goal is not only\ud to detect and count individual photons, but also to measure\ud the charge deposited in the detector by each photon, and\ud consequently determine its energy. Basically, we are aiming\ud at a spectrometer-in-a-pixel, or a “color X-ray camera”.\ud The approach we have followed towards this goal is the\ud design of small analog-to-digital-converters at the pixel level,\ud together with a very fast digital readout from the pixels to\ud the periphery of the chip, where the data will be transmitted\ud off-chip.\ud We will present here the design and measurement on prototype\ud chips of two different 4-bit pixel level ADCs. The\ud ADCs are optimized for very small area and low power, with\ud a resolution of 4-bits and a sample rate of 1 Msample/s. The\ud readout architecture is based around current-mode sense\ud amplifiers and asynchronous token-passing between the pixels.\ud This is done in order to achieve event-by-event readout\ud and, consequently, on-line imaging. We need to read eventby-\ud event (photon-by-photon), because we cannot have memory\ud on the pixels due to obvious size constraints. We use\ud current-mode sense amplifiers because they perform very\ud well in similar applications as very fast static-RAM readout

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Self-Reconfigurable Analog Arrays: Off-The Shelf Adaptive Electronics for Space Applications

Development of analog electronic solutions for space avionics is expensive and lengthy. Lack of flexible analog devices, counterparts to digital Field Programmable Gate Arrays (FPGA), prevents analog designers from benefits of rapid prototyping. This forces them to expensive and lengthy custom design, fabrication, and qualification of application specific integrated circuits (ASIC). The limitations come from two directions: commercial Field Programmable Analog Arrays (FPAA) have limited variability in the components offered on-chip; and they are only qualified for best case scenarios for military grade (-55C to +125C). In order to avoid huge overheads, there is a growing trend towards avoiding thermal and radiation protection by developing extreme environment electronics, which maintain correct operation while exposed to temperature extremes (-180degC to +125degC). This paper describes a recent FPAA design, the Self-Reconfigurable Analog Array (SRAA) developed at JPL. It overcomes both limitations, offering a variety of analog cells inside the array together with the possibility of self-correction at extreme temperatures

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

A Novel Frequency Based Current-to-Digital Converter with Programmable Dynamic Range

This work describes a novel frequency based Current to Digital converter, which would be fully realizable on a single chip. Biological systems make use of delay line techniques to compute many things critical to the life of an animal. Seeking to build up such a system, we are adapting the auditory localization circuit found in barn owls to detect and compute the magnitude of an input current. The increasing drive to produce ultra low-power circuits necessitates the use of very small currents. Frequently these currents need to accurately measured, but current solutions typically involve off-chip measurements. These are usually slow, and moving a current off chip increases noise to the system. Moving a system such as this completely on chip will allow for precise measurement and control of bias currents, and it will allow for better compensation of some common transistor mismatch issues. This project affords an extremely low power (100s nW) converter technology that is also very space efficient. The converter is completely asynchronous which yields ultra-low power standby operation [1]