Ultra-Compact mm-Wave Monolithic IC Doherty Power Amplifier for Mobile Handsets

YesThis work develops a novel dynamic load modulation Power Amplifier (PA) circuity that can provide an optimum compromise between linearity and efficiency while covering multiple cellular frequency bands. Exploiting monolithic microwave integrated circuits (MMIC) technology, a fully integrated 1W Doherty PA architecture is proposed based on 0.1 µm AlGaAs/InGaAs Depletion- Mode (D-Mode) technology provided by the WIN Semiconductors foundry. The proposed wideband DPA incorporates the harmonic tuning Class-J mode of operation, which aims to engineer the voltage waveform via second harmonic capacitive load termination. Moreover, the applied post-matching technique not only reduces the impedance transformation ratio of the conventional DPA, but also restores its proper load modulation. The simulation results indicate that the monolithic drive load modulation PA at 4 V operation voltage delivers 44% PAE at the maximum output power of 30 dBm at the 1 dB compression point, and 34% power-added efficiency (PAE) at 6 dB power back-off (PBO). A power gain flatness of around 14 ± 0.5 dB was achieved over the frequency band of 23 GHz to 27 GHz. The compact MMIC load modulation technique developed for the 5G mobile handset occupies the die area of 3.2.This research was funded by the European Regional Development Fund (FEDER), through COMPETE 2020, POR ALGARVE 2020, Fundação para a Ciência e a Tecnologia (FCT) under i-Five Project (POCI-01-0145-FEDER-030500). This work is also part of the POSITION-II project funded by the ECSEL joint Undertaking under grant number Ecsel-345 7831132-Postitio-II-2017-IA. This work is supported by FCT/MCTES through national funds and when applicable co-funded EU funds under the project UIDB/50008/2020-UIDP/50008/2020. The authors would like to thank the WIN Semiconductors foundry for providing the MMIC GaAs pHEMT PDKs and technical support. This work is supported by the Project TEC2017-88242-C3-2-R- Spanish Ministerio de Ciencia, Innovación e Universidades and EU-FEDER funding

Application of waveform engineering to GaN HFET characterisation and class F design

In this work, the largely theoretical existing research on class F has been extended to include a measured waveform based analysis. The results demonstrate how optimum class F performance can be achieved using real devices and highlights a number of interesting issues that a designer of a class F amplifier should consider.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

A novel approach for wide band high-efficiency power amplifier design

Wireless communication systems require an efficient and broadband RF frontend. RF Power Amplifiers (PA) are the most critical component in the RF frontend and are considered the bottleneck in high efficient wideband transmitters. The research starts with an investigation of high efficient operation modes based on waveform engineering. The outcome of the research can be divided into two main parts: The first concerns an analysis of high efficient modes of operation. The second part builds on first part looking at the PA’s efficiency-bandwidth perspective to design a wide band high efficient PA. The first part of the thesis, introduces a novel linear high efficient PA mode termed Injection Power Amplifier (IPA) that exceeds drain efficiency of 90% without relying on the nonlinearity of a PA at the compression region. This is achieved by presenting appropriate negative harmonic impedances to a transistor to reduce the dissipated power, thus, increasing the efficiency of conversion of DC to fundamental RF power. The theoretical analysis of this mode is presented and a validation measurement has been carried out using an active load-pull system. The measured results confirmed the theoretical predictions of achieving high efficiency in a linear PA operation. Furthermore, a PA structure that is based on two parallel PAs (main PA and auxiliary PA) has been proposed along with the practical circuit realization of the IPA mode. In addition, a PA prototype has been designed following a methodology of nonlinear PA design based on waveform engineering. The PA prototype has been characterized and built operating at 0.9 GHz with an output power of 10 W showing a high linear efficient operation of 80% drain efficiency at only 1 dB compression level. The second part of this work aims to tackle today’s limitation of high efficient wideband PAs beyond octave bandwidth. A conceptual system based on multimode operation has been proposed to overcome the need for bandlimiting passive harmonic termination. This novel approach is based on combining passive termination with active harmonic injection to get around the theoretical limitation of one octave for high efficiency harmonically tuned power amplifiers. Furthermore, a proof of concept PA prototype has been designed and built for a two octave bandwidth (4:1 bandwidth) operating from 0.63-2.56 GHz and providing the rated output power of a 10 W GaN device with a PAE greater than 50% at only 1 dB compression point. This multi-mode approach shows a promising technique for future wideband high efficiency wireless transmitters.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Dynamically Controllable Integrated Radiation and Self-Correcting Power Generation in mm-Wave Circuits and Systems

This thesis presents novel design methodologies for integrated radiators and power generation at mm-wave frequencies that are enabled by the continued integration of various electronic and electromagnetic (EM) structures onto the same substrate. Beginning with the observation that transistors and their connections to EM radiating structures on an integrated substrate are essentially free, the concept of multi-port driven (MPD) radiators is introduced, which opens a vast design space that has been generally ignored due to the cost structure associated with discrete components that favors fewer transistors connected to antennas through a single port. From Maxwell's equations, a new antenna architecture, the radial MPD antennas based on the concept of MPD radiators, is analyzed to gain intuition as to the important design parameters that explain the wide-band nature of the antenna itself. The radiator is then designed and implemented at 160 GHz in a 0.13 um SiGe BiCMOS process, and the single element design has a measured effective isotropic radiated power (EIRP) of +4.6 dBm with a total radiated power of 0.63 mW. Next, the radial MPD radiator is adapted to enable dynamic polarization control (DPC). A DPC antenna is capable of controlling its radiated polarization dynamically, and entirely electronically, with no mechanical reconfiguration required. This can be done by having multiple antennas with different polarizations, or within a single antenna that has multiple drive points, as in the case of the MPD radiator with DPC. This radiator changes its polarization by adjusting the relative phase and amplitude of its multiple ports to produce polarizations with any polarization angle, and a wide range of axial ratios. A 2x1 MPD radiator array with DPC at 105 GHz is presented whose measurements show control of the polarization angle throughout the entire 0 degree through 180 degree range while in the linear polarization mode and maintaining axial ratios above 10 dB in all cases. Control of the axial ratio is also demonstrated with a measured range from 2.4 dB through 14 dB, while maintaining a fixed polarization angle. The radiator itself has a measured maximum EIRP of +7.8 dBm, with a total radiated power of 0.9 mW, and is capable of beam steering. MPD radiators were also applied in the domain of integrated silicon photonics. For these designs, the driver transistor circuitry was replaced with silicon optical waveguides and photodiodes to produce a 350 GHz signal. Three of these optical MPD radiator designs have been implemented as 2x2 arrays at 350 GHz. The first is a beam forming array that has a simulated gain of 12.1 dBi with a simulated EIRP of -2 dBm. The second has the same simulated performance, but includes optical phase modulators that enable two-dimensional beam steering. Finally, a third design incorporates multi-antenna DPC by combining the outputs of both left and right handed circularly polarized MPD antennas to produce a linear polarization with controllable polarization angle, and has a simulated gain of 11.9 dBi and EIRP of -3 dBm. In simulation, it can tune the polarization from 0 degrees through 180 degrees while maintaining a radiated power that has a 0.35 dB maximum deviation from the mean. The reliability of mm-wave radiators and power amplifiers was also investigated, and two self-healing systems have been proposed. Self-healing is a global feedback method where integrated sensors detect the performance of the circuit after fabrication and report that data to a digital control algorithm. The algorithm then is capable of setting actuators that can control the performance of the mm-wave circuit and counteract any performance degradation that is observed by the sensors. The first system is for a MPD radiator array with a partially integrated self-healing system. The self-healing MPD radiator senses substrate modes through substrate mode pickup sensors and infers the far-field radiated pattern from those sensors. DC current sensors are also included to determine the DC power consumption of the system. Actuators are implemented in the form of phase and amplitude control of the multiple drive points. The second self-healing system is a fully integrated self-healing power amplifier (PA) at 28 GHz. This system measures the output power, gain and efficiency of the PA using radio frequency (RF) power sensors, DC current sensors and junction temperature sensors. The digital block is synthesized from VHDL code on-chip and it can actuate the output power combining matching network using tunable transmission line stubs, as well as the DC operating point of the amplifying transistors through bias control. Measurements of 20 chips confirm self-healing for two different algorithms for process variation and transistor mismatch, while measurements from 10 chips show healing for load impedance mismatch, and linearity healing. Laser induced partial and total transistor failure show the benefit of self-healing in the case of catastrophic failure, with improvements of up to 3.9 dB over the default case. An exemplary yield specification shows self-healing improving the yield from 0% up through 80%.</p

Wideband Watt-Level Spatial Power-Combined Power Amplifier in SiGe BiCMOS Technology for Efficient mm-Wave Array Transmitters

The continued demand for high-speed wireless communications is driving the development of integrated high-power transmitters at millimeter wave (mm-Wave) frequencies. Si-based technologies allow achieving a high level of integration but usually provide insufficient generated RF power to compensate for the increased propagation and material losses at mm-Wave bands due to the relatively low breakdown voltage of their devices. This problem can be reduced significantly if one could combine the power of multiple active devices on each antenna element. However, conventional on-chip power combining networks have inherently high insertion losses reducing transmitter efficiency and limiting its maximum achievable output power.This work presents a non-conventional design approach for mm-Wave Si-based Watt-level power amplifiers that is based on novel power-combining architecture, where an array of parallel custom PA-cells suited on the same chip is interfaced to a single substrate integrated waveguide (to be a part of an antenna element). This allows one to directly excite TEm0 waveguide modes with high power through spatial power combining functionality, obviating the need for intermediate and potentially lossy on-chip power combiners. The proposed solution offers wide impedance bandwidth (50%) and low insertion losses (0.4 dB), which are virtually independent from the number of interfaced PA-cells. The work evaluates the scalability bounds of the architecture as well as discusses the critical effects of coupled non-identical PA-cells, which are efficiently reduced by employing on-chip isolation load resistors.The proposed architecture has been demonstrated through an example of the combined PA with four differential cascode PA-cells suited on the same chip, which is flip-chip interconnected to the combiner placed on a laminate. This design is implemented in a 0.25 um SiGe BiCMOS technology. The PA-cell has a wideband performance (38.6%) with both high peak efficiency (30%) and high saturated output power (24.9 dBm), which is the highest reported output power level obtained without the use of circuit-level power combining in Si-based technologies at Ka-band. In order to achieve the optimal system-level performance of the combined PA, an EM-circuit-thermal optimization flow has been proposed, which accounts for various multiphysics effects occurring in the joint structure. The final PA achieves the peak PAE of 26.7% in combination with 30.8 dBm maximum saturated output power, which is the highest achievable output power in practical applications, where the 50-Ohms load is placed on a laminate. The high efficiency (&gt;20%) and output power (&gt;29.8 dBm) over a wide frequency range (30%) exceed the state-of-the-art in Si-based PAs

The Glacier Complexes of the Mountain Massifs of the North-West of Inner Asia and their Dynamics

The subject of this paper is the glaciation of the mountain massifs Mongun-Taiga, Tavan-Boghd-Ola, Turgeni- Nuru, and Harhira-Nuru. The glaciation is represented mostly by small forms that sometimes form a single complex of domeshaped peaks. According to the authors, the modern glaciated area of the mountain massifs is 21.2 km2 (Tavan-Boghd-Ola), 20.3 km2 (Mongun-Taiga), 42 km2 (Turgeni- Nuru), and 33.1 km2 (Harhira-Nuru). The area of the glaciers has been shrinking since the mid 1960’s. In 1995–2008, the rate of reduction of the glaciers’ area has grown considerably: valley glaciers were rapidly degrading and splitting; accumulation of morainic material in the lower parts of the glaciers accelerated. Small glaciers transformed into snowfields and rock glaciers. There has been also a degradation of the highest parts of the glaciers and the collapse of the glacial complexes with a single zone of accumulation into isolated from each other glaciers. Reduced snow cover area has led to a rise in the firn line and the disintegration of a common accumulation area of the glacial complex. In the of the Mongun-Taiga massif, in 1995– 2008, the firn line rose by 200–300 m. The reduction of the glaciers significantly lagged behind the change in the position of the accumulation area boundary. In the past two years, there has been a significant recovery of the glaciers that could eventually lead to their slower degradation or stabilization of the glaciers in the study area

Risk based life management of offshore structures and equipment

Risk based approaches are gaining currency as industry looks for rational, efficient and flexible approaches to managing their structures and equipment. When applied to inspection and maintenance of industrial assets, risk based approaches differ from other approaches mainly in their assessment of failure in its wider context and ramifications. These advanced techniques provide more insight into the causes and avoidance of structural failure and competing risks, as well as the resources needed to manage them. Measuring risk is a challenge that is being met with state of the art technology, skills, knowledge and experience. The thesis presents risk based approaches to solving two specific types of problem in the management of offshore structures and equipments. The first type is finding the optimum timing of an asset life management action such that financial benefit is maximised, considering the cost of the action and the risk (quantified in monetary terms) of not undertaking that action. The approach presented here is applied to managing remedial action in offshore wind farms and specifically to corroded wind turbine tower structures. The second type of problem is how to optimise resources using risk based criteria for managing competing demands. The approach presented here is applied to stocking spares in the shipping sector, where the cost of holding spares is balanced against the risk of failing to meet demands for spares. Risk is the leitmotiv running through this thesis. The approaches discussed here will find application in a variety of situations where competing risks are being managed within constraints

High-Power Microwave/ Radio-Frequency Components, Circuits, and Subsystems for Next-Generation Wireless Radio Front-Ends

As the wireless communication systems evolve toward the future generation, intelligence will be the main signature/trend, well known as the concepts of cognitive and software-defined radios which offer ultimate data transmission speed, spectrum access, and user capacity. During this evolution, the human society may experience another round of `information revolution\u27. However, one of the major bottlenecks of this promotion lies in hardware realization, since all the aforementioned intelligent systems are required to cover a broad frequency range to support multiple communication bands and dissimilar standards. As the essential part of the hardware, power amplifiers (PAs) capable of operating over a wide bandwidth have been identified as the key enabling technology. This dissertation focuses on novel methodologies for designing and realizing broadband high-power PAs, their integration with high-quality-factor (high-Q) tunable filters, and relevant investigations on the reliabilities of these tunable devices. It can be basically divided into three major parts: 1.Broadband High-Efficiency Power Amplifiers. Obtaining high PA efficiency over a wide bandwidth is very challenging, because of the difficulty of performing broadband multi-harmonic matching. However, high efficiency is the critical feature for high-performance PAs due to the ever-increasing demands for environmental friendliness, energy saving, and longer battery life. In this research, novel design methodologies of broad-band highly efficient PAs are proposed, including the first-ever mode-transferring PA theory, novel matching network topology, and wideband reconfigurable PA architecture. These techniques significantly advance the state-of-the-art in terms of bandwidth and efficiency. 2.Co-Design of PAs and High-Q Tunable Filters. When implementing the intelligent communication systems, the conventional approach based on independent RF design philosophy suffers from many inherent defects, since no global optimization is achieved leading to degraded overall performance. An attractive method to solve these difficulties is to co-design critical modules of the transceiver chain. This dissertation presents the first-ever co-design of PAs and tunable filters, in which the redundant inter-module matching is entirely eliminated, leading to minimized size & cost and maximized overall performance. The saved hardware resources can be further transferred to enhance system functionalities. Moreover, we also demonstrate that co-design of PAs and filters can lead to more functionalities/benefits for the wireless systems, e.g. efficient and linear amplification of dual-carrier (or multi-carrier) signals. 3.High-Power/Non-Linear Study on Tunable Devices. High-power limitation/power handling is an everlasting theme of tunable devices, as it determines the operational life and is the threshold for actual industrial applications. Under high-power operation, the high RF voltage can lead to failures like tuners\u27 mechanical deflections and gas discharge in the small air spacing of the cavity. These two mechanisms are studied independently with their instantaneous and long-term effects on the device performance. In addition, an anti-biased topology of electrostatic RF MEMS varactors and tunable filters is proposed and experimentally validated for reducing the non-linear effect induced by bias-noise. These investigations will enlighten the designers on how to avoid and/or minimize the non-ideal effects, eventually leading to longer life cycle and performance sustainability of the tunable devices

Dynamic Focusing of Large Arrays for Wireless Power Transfer and Beyond

We present architectures, circuits, and algorithms for dynamic 3-D lensing and focusing of electromagnetic power in radiative near- and far-field regions by arrays that can be arbitrary and nonuniform. They can benefit applications such as wireless power transfer at a distance (WPT-AD), volumetric sensing and imaging, high-throughput communications, and optical phased arrays. Theoretical limits on system performance are calculated. An adaptive algorithm focuses the power at the receiver(s) without prior knowledge of its location(s). It uses orthogonal bases to change the phases of multiple elements simultaneously to enhance the dynamic range. One class of such 2-D orthogonal and pseudo-orthogonal masks is constructed using the Hadamard and pseudo-Hadamard matrices. Generation and recovery units (GU and RU) work collaboratively to focus energy quickly and reliably with no need for factory calibration. Orthogonality enables batch processing in high-latency and low-rate communication settings. Secondary vector-based calculations allow instantaneous refocusing at different locations using element-wise calculations. An emulator enables further evaluation of the system. We demonstrate modular WPT-AD GUs of up to 400 elements utilizing arrays of 65-nm CMOS ICs to focus power on RUs that convert the RF power to dc. Each RFIC synthesizes 16 independently phase-controlled RF outputs around 10 GHz from a common single low-frequency reference. Detailed measurements demonstrate the feasibility and effectiveness of RF lensing techniques presented in this article. More than 2 W of dc power can be recovered through a wireless transfer at distances greater than 1 m. The system can dynamically project power at various angles and at distances greater than 10 m. These developments are another step toward unified wireless power, sensing, and communication solutions in the future