30,970 research outputs found
Recommended from our members
Noise shaping Asynchronous SAR ADC based time to digital converter
Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin
Current-Mode Techniques for the Implementation of Continuous- and Discrete-Time Cellular Neural Networks
This paper presents a unified, comprehensive approach
to the design of continuous-time (CT) and discrete-time
(DT) cellular neural networks (CNN) using CMOS current-mode
analog techniques. The net input signals are currents instead
of voltages as presented in previous approaches, thus avoiding
the need for current-to-voltage dedicated interfaces in image
processing tasks with photosensor devices. Outputs may be either
currents or voltages. Cell design relies on exploitation of current
mirror properties for the efficient implementation of both linear
and nonlinear analog operators. These cells are simpler and
easier to design than those found in previously reported CT
and DT-CNN devices. Basic design issues are covered, together
with discussions on the influence of nonidealities and advanced
circuit design issues as well as design for manufacturability
considerations associated with statistical analysis. Three prototypes
have been designed for l.6-pm n-well CMOS technologies.
One is discrete-time and can be reconfigured via local logic for
noise removal, feature extraction (borders and edges), shadow
detection, hole filling, and connected component detection (CCD)
on a rectangular grid with unity neighborhood radius. The other
two prototypes are continuous-time and fixed template: one for
CCD and other for noise removal. Experimental results are given
illustrating performance of these prototypes
Fast synchronization 3R burst-mode receivers for passive optical networks
This paper gives a tutorial overview on high speed burst-mode receiver (BM-RX) requirements, specific for time division multiplexing passive optical networks, and design issues of such BM-RXs as well as their advanced design techniques. It focuses on how to design BM-RXs with short burst overhead for fast synchronization. We present design principles and circuit architectures of various types of burst-mode transimpedance amplifiers, burst-mode limiting amplifiers and burst-mode clock and data recovery circuits. The recent development of 10 Gb/s BM-RXs is highlighted also including dual-rate operation for coexistence with deployed PONs and on-chip auto reset generation to eliminate external timing-critical control signals provided by a PON medium access control. Finally sub-system integration and state-of-the-art system performance for 10 Gb/s PONs are reviewed
Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals
Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve
Beyond Moore's technologies: operation principles of a superconductor alternative
The predictions of Moore's law are considered by experts to be valid until
2020 giving rise to "post-Moore's" technologies afterwards. Energy efficiency
is one of the major challenges in high-performance computing that should be
answered. Superconductor digital technology is a promising post-Moore's
alternative for the development of supercomputers. In this paper, we consider
operation principles of an energy-efficient superconductor logic and memory
circuits with a short retrospective review of their evolution. We analyze their
shortcomings in respect to computer circuits design. Possible ways of further
research are outlined.Comment: OPEN ACCES
A 100-MIPS GaAs asynchronous microprocessor
The authors describe how they ported an asynchronous microprocessor previously implemented in CMOS to gallium arsenide, using a technology-independent asynchronous design technique. They introduce new circuits including a sense-amplifier, a completion detection circuit, and a general circuit structure for operators specified by production rules. The authors used and tested these circuits in a variety of designs
Low Power Processor Architectures and Contemporary Techniques for Power Optimization â A Review
The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER
- âŠ