Leakage Minimization Technique for Nanoscale CMOS VLSI

Because of the continued scaling of technology and supply-threshold voltage, leakage power has become more significant in power dissipation of nanoscale CMOS circuits. Therefore, estimating the total leakage power is critical to designing low-power digital circuits. In nanometer CMOS circuits, the main leakage components are the subthreshold, gate-tunneling, and reverse-biased junction band-to-band-tunneling (BTBT) leakage currents

Ultra-low Voltage Digital Circuits and Extreme Temperature Electronics Design

Certain applications require digital electronics to operate under extreme conditions e.g., large swings in ambient temperature, very low supply voltage, high radiation. Such applications include sensor networks, wearable electronics, unmanned aerial vehicles, spacecraft, and energyharvesting systems. This dissertation splits into two projects that study digital electronics supplied by ultra-low voltages and build an electronic system for extreme temperatures. The first project introduces techniques that improve circuit reliability at deep subthreshold voltages as well as determine the minimum required supply voltage. These techniques address digital electronic design at several levels: the physical process, gate design, and system architecture. This dissertation analyzes a silicon-on-insulator process, Schmitt-trigger gate design, and asynchronous logic at supply voltages lower than 100 millivolts. The second project describes construction of a sensor digital controller for the lunar environment. Parts of the digital controller are an asynchronous 8031 microprocessor that is compatible with synchronous logic, memory with error detection and correction, and a robust network interface. The digitial sensor ASIC is fabricated on a silicon-germanium process and built with cells optimized for extreme temperatures

DESIGN OF EFFICIENT NANOELECTRONIC MEMORY AND CRYPTOGRAPHIC CIRCUITS

This thesis presents the design of Nanoelectronic Memory cell and arrays compatible with molecular switch (nanodevice) electrical characteristics. The proposed transmission gate based CMOL (hybrid CMOS / Molecular) memory cell surmounts the operational difficulties facing previous design. The Control circuitry with improved multiplexer design is introduced in this dissertation. Yield improvement through replacing the defective cell with a free cell can be achieved using a proposed algorithm. Moreover, the proposed memory cell has the same area as the existing CMOL inverter cells allowing easier implementation of both logic and memory circuits on the same chip. An efficient hardware implementation of the SBox from the Advanced Encryption Standard (AES) is presented in this dissertation. Modification of the design was achieved by adding Tri­ state Inverter followed by an Inverter (TII). Simulation results show a reduction in the average power dissipation as well as the time delays. Reduction of supply voltage and using low Vdd in non critical path improved the performance by reducing the energy delay product. Different transistors models with dual threshold voltage (Vt) based on 65nm CMOS technology were applied to the design to achieve further improvement. Keywords: CMOL, CMOL circuits, Nanoscale memory, Control Circuit, AES, SBox, Deep sub-micron CMOS technology, Tri-state Inverter, Low Power SBo

Cell Library Creation using ALF

The design of Integrated Circuit (ASICs and SoCs) typically relies on the availability of a library consisting of predefined components called technology cells. Silicon vendors use proprietary formats to describe technology cells and macro modules in conjunction with numerous translators to feed technology library data to Electronic Design Automation (EDA) tools. Multiple grammar formats are used to represent various aspects of the cells in the same technology library, such as behavior for simulation, timing parameters for synthesis, physical data for layout, noise parameters for signal integrity checks, etc. In addition, most of these formats are highly tool-oriented and are not grammatically consistent. In this paper we will discuss the newly adopted IEEE 1603-2003 Advanced Library Format (ALF) standard which eliminates such drawbacks. This standard defines a grammar for accurate and comprehensive modeling of technology libraries and macro modules in order to bridge the growing gap between new design rules and the analysis required for complex high-end IC implementations

Digital implementation of a wavelet-based event detector for cardiac pacemakers

This paper presents a digital hardware implementation of a novel wavelet-based event detector suitable for the next generation of cardiac pacemakers. Significant power savings are achieved by introducing a second operation mode that shuts down 2/3 of the hardware for long time periods when the pacemaker patient is not exposed to noise, while not degrading performance. Due to a 0.13-mu m CMOS technology and the low clock frequency of 1 kHz, leakage power becomes the dominating power source. By introducing sleep transistors in the power-supply rails, leakage power of the hardware being shut off is reduced by 97%. Power estimation on RTL-level shows that the overall power consumption is reduced by 67% with a dual operation mode. Under these conditions, the detector is expected to operate in the sub-mu W region. Detection performance is evaluated by means of databases containing electrograms to which five types of exogenic and endogenic interferences are added. The results show that reliable detection is obtained at moderate and low signal to noise-ratios (SNRs). Average detection performance in terms of detected events and false alarms for 25-dB SNR is P-D = 0.98 and P-FA = 0.014, respectively

System-Level Leakage Power Estimation Model for ASIC Designs

With advances in CMOS- technology and sub-micron process, leakage power dissipation has become a critical design metric. To incorporate more functions, designs are getting complex, thereby increases leakage power dissipation. Low power design objective requires early exploration and estimation. In this paper, we present the power estimation models for ASIC (Application Specific Integrated Circuit) based designs at the C-level of abstraction. The method includes analysis and extraction of the application specific information from the LLVM (Low-Level Virtual Machine) bit-code; which further applies to train the neural network. The trained model is applied in the estimation of the leakage power. Estimation of design power using our models is compared to the implemented measurement, which demonstrates its accuracy. In addition, the proposed methodology is significantly quicker and abolishes the need of synthesis based exploration

Optimal digital system design in deep submicron technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 165-174).The optimization of a digital system in deep submicron technology should be done with two basic principles: energy waste reduction and energy-delay tradeoff. Increased energy resources obtained through energy waste reduction are utilized through energy-delay tradeoffs. The previous practice of obliviously pursuing performance has led to the rapid increase in energy consumption. While energy waste due to unnecessary switching could be reduced with small increases in logic complexity, leakage energy waste still remains as a major design challenge. We find that fine-grain dynamic leakage reduction (FG-DLR), turning off small subblocks for short idle intervals, is the key for successful leakage energy saving. We introduce an FG-DLR circuit technique, Leakage Biasing, which uses leakage currents themselves to bias the circuit into the minimum leakage state, and apply it to primary SRAM arrays for bitline leakage reduction (Leakage-Biased Bitlines) and to domino logic (Leakage-Biased Domino). We also introduce another FG-DLR circuit technique, Dynamic Resizing, which dynamically downsizes transistors on idle paths while maintaining the performance along active critical paths, and apply it to static CMOS circuits.(cont.) We show that significant energy reduction can be achieved at the same computation throughput and communication bandwidth by pipelining logic gates and wires. We find that energy saved by pipelining datapaths is eventually limited by latch energy overhead, leading to a power-optimal pipelining. Structuring global wires into on-chip networks provides a better environment for pipelining and leakage energy saving. We show that the energy-efficiency increase through replacement with dynamically packet-routed networks is bounded by router energy overhead. Finally, we provide a way of relaxing the peak power constraint. We evaluate the use of Activity Migration (AM) for hot spot removal. AM spreads heat by transporting computation to a different location on the die. We show that AM can be used either to increase the power that can be dissipated by a given package, or to lower the operating temperature and hence the operating energy.by Seongmoo Heo.Ph.D

Electronic systems for intelligent particle tracking in the High Energy Physics field

This Ph.D thesis describes the development of a novel readout ASIC for hybrid pixel detector with intelligent particle tracking capabilities in High Energy Physics (HEP) application, called Macro Pixel ASIC (MPA). The concept of intelligent tracking is introduced for the upgrade of the particle tracking system of the Compact Muon Solenoid (CMS) experiment of the Large Hadron Collider (LHC) at CERN: this detector must be capable of selecting at front--end level the interesting particle and of providing them continuously to the back-end. This new functionality is required to cope with the improved performances of the LHC when, in about ten years' time, a major upgrade will lead to the High Luminosity scenario (HL-LHC). The high complexity of the digital logic for particle selection and the very low power requirement of 95% in particle selection and a data reduction from 200 Tb/s/cm2 to 1 Tb/s/cm2. A prototype, called MPA-Light, has been designed, produced and tested. According to the measurements, the prototype respects all the specications. The same device has been used for multi-chip assembly with a pixelated sensor. The assembly characterization with radioactive sources conrms the result obtained on the bare chip

Course grained low power design flow using UPF

Increased system complexity has led to the substitution of the traditional bottom-up design flow by systematic hierarchical design flow. The main motivation behind the evolution of such an approach is the increasing difficulty in hardware realization of complex systems. With decreasing channel lengths, few key problems such as timing closure, design sign-off, routing complexity, signal integrity, and power dissipation arise in the design flows. Specifically, minimizing power dissipation is critical in several high-end processors. In high-end processors, the design complexity contributes to the overall dynamic power while the decreasing transistor size results in static power dissipation. This research aims at optimizing the design flow for power and timing using the unified power format (UPF). UPF provides a strategic format to specify power-aware design information at every stage in the flow. The low power reduction techniques enforced in this research are multi-voltage, multi-threshold voltage (Vth), and power gating with state retention. An inherent design challenge addressed in this research is the choice of power optimization techniques as the flow advances from synthesis to physical design. A top-down digital design flow for a 32 bit MIPS RISC processor has been implemented with and without UPF synthesis flow for 65nm technology. The UPF synthesis is implemented with two voltages, 1.08V and 0.864V (Multi-VDD). Area, power and timing metrics are analyzed for the flows developed. Power savings of about 20 % are achieved in the design flow with \u27multi-threshold\u27 power technique compared to that of the design flow with no low power techniques employed. Similarly, 30 % power savings are achieved in the design flow with the UPF implemented when compared to that of the design flow with \u27multi-threshold\u27 power technique employed. Thus, a cumulative power savings of 42% has been achieved in a complete power efficient design flow (UPF) compared to that of the generic top-down standard flow with no power saving techniques employed. This is substantiated by the low voltage operation of modules in the design, reduction in clock switching power by gating clocks in the design and extensive use of HVT and LVT standard cells for implementation. The UPF synthesis flow saw the worst timing slack and more area when compared to those of the `multi-threshold\u27 or the generic flow. Percentage increase in the area with UPF is approximately 15%; a significant source for this increase being the additional power controlling logic added

Technical Design Report for the PANDA Micro Vertex Detector

This document illustrates the technical layout and the expected performance of the Micro Vertex Detector (MVD) of the PANDA experiment. The MVD will detect charged particles as close as possible to the interaction zone. Design criteria and the optimisation process as well as the technical solutions chosen are discussed and the results of this process are subjected to extensive Monte Carlo physics studies. The route towards realisation of the detector is outlined