Surface relief structures for multiple beam LO generation

Linear and binary holograms for use in heterodyne detection with 10.6 micron imaging arrays are described. The devices match the amplitude and phase of the local oscillator to the received signal and thus maximize the system signal to noise ratio and resolution and minimize heat generation on the focal plane. In both the linear and binary approaches, the holographic surface-relief pattern is coded to generate a set of local oscillator beams when the relief pattern is illuminated by a single planewave. Each beam of this set has the same amplitude shape distribution as, and is collinear with, each single element wavefront illuminating array

Receiver Front-Ends in CMOS with Ultra-Low Power Consumption

Historically, research on radio communication has focused on improving range and data rate. In the last decade, however, there has been an increasing demand for low power and low cost radios that can provide connectivity with small devices around us. They should be able to offer basic connectivity with a power consumption low enough to function extended periods of time on a single battery charge, or even energy scavenged from the surroundings. This work is focused on the design of ultra-low power receiver front-ends intended for a receiver operating in the 2.4GHz ISM band, having an active power consumption of 1mW and chip area of 1mm². Low power consumption and small size make it hard to achieve good sensitivity and tolerance to interference. This thesis starts with an introduction to the overall receiver specifications, low power radio and radio standards, front-end and LO generation architectures and building blocks, followed by the four included papers. Paper I demonstrates an inductorless front-end operating at 915MHz, including a frequency divider for quadrature LO generation. An LO generator operating at 2.4GHz is shown in Paper II, enabling a front-end operating above 2GHz. Papers III and IV contain circuits with combined front-end and LO generator operating at or above the full 2.45GHz target frequency. They use VCO and frequency divider topologies that offer efficient operation and low quadrature error. An efficient passive-mixer design with improved suppression of interference, enables an LNA-less design in Paper IV capable of operating without a SAW-filter

LC-VCO design optimization methodology based on the gm/ID ratio for nanometer CMOS technologies

In this paper, an LC voltage-controlled oscillator (LC-VCO) design optimization methodology based on the gm/ID technique and on the exploration of all inversion regions of the MOS transistor (MOST) is presented. An in-depth study of the compromises between phase noise and current consumption permits optimization of the design for given specifications. Semiempirical models of MOSTs and inductors, obtained by simulation, jointly with analytical phase noise models, allow to get a design space map where the design tradeoffs are easily identified. Four LC-VCO designs in different inversion regions in a 90-nm CMOS process are obtained with the proposed methodology and verified with electrical simulations. Finally, the implementation and measurements are presented for a 2.4-GHz VCO operating in moderate inversion. The designed VCO draws 440 μA from a 1.2-V power supply and presents a phase noise of -106.2 dBc/Hz at 400 kHz from the carrier

QCD Coherence and the Top Quark Asymmetry

Coherent QCD radiation in the hadroproduction of top quark pairs leads to a forward--backward asymmetry that grows more negative with increasing transverse momentum of the pair. This feature is present in Monte Carlo event generators with coherent parton showering, even though the production process is treated at leading order and has no intrinsic asymmetry before showering. In addition, depending on the treatment of recoils, showering can produce a positive contribution to the inclusive asymmetry. We explain the origin of these features, compare them in fixed-order calculations and the Herwig++, Pythia and Sherpa event generators, and discuss their implications.Comment: 28 pages, 11 figures, 2 table

Three-antenna two-dimensional imaging correlation radiometer: concept and preliminary results

Peer ReviewedPostprint (published version

A 6-to-18 GHz tunable concurrent dual-band receiver front end for scalable phased arrays in 130nm CMOS

This paper presents a study and design of tunable concurrent dual-band receiver. Different system architectures and building blocks have been compared and analyzed. A tunable concurrent dual-band receiver front end has then been fabricated and characterized. It operates across a tri-tave 6-18 GHz bandwidth with a nominal 17-25 dB conversion gain, worst-case -15 dBm IIP3, and worst-case -24.5 dBm ICP 1 dB

Remote downconversion scheme for uplink configuration in radio/fiber systems

The authors present a novel technology for uplink transmission in radio over fiber (RoF) distribution systems. The technique employs remote downconversion of the uplink data to intermediate frequency (IF) in the base station (BS). The local oscillator (LO) signal for the downconversion is optically generated in the central station (CS) and sent to the BS via optical fiber. The IF uplink data is then modulated onto an optical carrier and sent to the CS, where the baseband conversion takes place. By employing this method of uplink connection simplicity and cost efficiency of the BS is achieved