Investigation and Implementation of Dicode Pulse Position Modulation Over Indoor Visible Light Communication System

A visible light communication (VLC) system with green technology is available and enables users to use white LEDs for illumination as well as for high data rate transmission over wireless optical links. In addition, LEDs have advantages of low power consumption, high speed with power efficiency and low cost. Therefore, a great deal of research is considered for indoor VLC, as it offers huge bandwidth whilst using a significant modulation technique. This thesis is concerned with the investigation and implementation of the dicode pulse position modulation (DiPPM) scheme over a VLC link using white LED sources. Novel work is carried out for applying DiPPM over a VLC channel theoretically and experimentally including a comparison with digital PPM (DPPM) in order to examine the system performance. Moreover, a proposal of variable DiPPM (VDiPPM) is presented in this thesis for dimming control. The indoor VLC channel characteristics have been investigated for two propagation prototypes. Two models have been proposed and developed with DiPPM and DPPM being applied over the VLC channel. A computer simulation for the proposed models for both DiPPM and DPPM systems is performed in order to analyse the receiver sensitivity with the effect of intersymbol interference (ISI). Both systems are operating at 100 Mbps and 1 Gbps for a BER of 10-9. An improvement in sensitivity being achieved by the DiPPM compared to the DPPM VLC system. The system performance has been carried out by Mathcad software. The predicted DiPPM receiver sensitivity outperforms DPPM receiver at by -5.55 dBm and -8.24 dBm, at 1 Gbps data rate, and by -5.53 dBm and -8.22 dBm, at 100 Mbps, without and with guard intervals, respectively. In both cases the optical receiver sensitivity is increased when the ISI is ignored. These results based on the received optical power required by each modulation scheme. Further work has been done in mathematical evaluation carried out to calculate the optical receiver sensitivity to verify the comparison between the two systems. The original numerical results show that DiPPM VLC system provides a better sensitivity than a DPPM VLC system at a selected BER of 10-9 when referred to the same preamplifier at wavelength of 650 nm and based on the equivalent input noise current generated by the optical front end receiver. The results show that the predicted sensitivity for DPPM is greater than that of DPPM by about 1 dBm when both systems operating at 100 Mbps and 1 Gbps. Also, it is show that the receiver sensitivity is increased when the ISI is limited. Experimentally, a complete indoor VLC system has been designed and implemented using Quartus II 11.1 software for generating VHDL codes and using FPGA development board (Cyclone IV GX) as main interface real-time transmission unit in this system. The white LEDs chip based transmitter and optical receiver have been constructed and tested. The measurements are performed by using LED white light as an optical transmitter faced to photodiode optical receiver on desk. Due to the LED bandwidth limitation the achieved operating data rate, using high speed LED driver, is 5.5 Mbps at BER of 10-7. The original results for the measurements determined that the average photodiode current produced by using DiPPM and DPPM optical receivers are 8.50 μA and 10.22 μA, respectively. And this in turn indicates that the DiPPM receiver can give a better sensitivity of -17.24 dBm while compared to the DPPM receiver which gives is -16.44 dBm. The original practical results proved the simulation and theoretical results where higher performance is achieved when a DiPPM scheme is used compared to DPPM scheme over an indoor VLC system

ASK-based spatial multiplexing RGB scheme using symbol-dependent self-interference for detection

We propose a vsible light communication scheme utilizing red, green and blue lightemitting diodes (LEDs) and three color-Tuned photodiodes. Amplitude shift keying modulation is considered, and its effect on light emission in terms of flickering, dimming, and color rendering is discussed. The presence of interference at each photodiode generated by the other two colors is used to improve detection since interference is symbol-dependent. Moreover, the capability of the photodiodes to follow the LEDs speed is considered by analyzing the possibility of equalizing the received signal, and also self-interference mitigation is proposed. The system performance is evaluated both with computer simulations and tests on an Arduino board implementation

Optical energy-constrained slot-amplitude modulation for dimmable VLC. Suboptimal detection and performance evaluation

Energy-constrained slot-amplitude modulation (ECSAM) enables light dimming, eliminates light flicker and constrains the peak optical power while providing robust communication links. However, the complexity of the maximum-likelihood (ML) based ECSAM receiver increases exponentially with required spectral efficiency. This paper provides a comprehensive performance evaluation of ECSAM for the indoor visible light communication (VLC) channel with multipath propagation under realistic illumination constraints and imperfect channel estimation. A sub-optimal receiver that employs a slot-by-slot detection algorithm followed by a slot-correction mechanism for reducing the receiver complexity is proposed. Additionally, the method for optimal selection of parameters when designing the signal waveform is presented. The analytical upper bound on the symbol error rate of ECSAM is derived using the union-bound technique. The results show that the error performance of the sub-optimal receiver are comparable to that of the optimal ML receiver. Compared with conventional power or bandwidth efficient VLC modulation techniques such as multiple pulse position modulation (MPPM) and pulse amplitude modulation (PAM), ECSAM provides complete flexibility in modifying the signal constellation for a desired dimming level to maximise the spectral efficiency and provide a robust bit error rate performance especially in the multipath propagation channel induced intersymbol interference

Interference Suppression in Massive MIMO VLC Systems

The focus of this dissertation is on the development and evaluation of methods and principles to mitigate interference in multiuser visible light communication (VLC) systems using several transmitters. All components of such a massive multiple-input multiple-output (MIMO) system are considered and transformed into a communication system model, while also paying particular attention to the hardware requirements of different modulation schemes. By analyzing all steps in the communication process, the inter-channel interference between users is identified as the most critical aspect. Several methods of suppressing this kind of interference, i.e. to split the MIMO channel into parallel single channels, are discussed, and a novel active LCD-based interference suppression principle at the receiver side is introduced as main aspect of this work. This technique enables a dynamic adaption of the physical channel: compared to solely software-based or static approaches, the LCD interference suppression filter achieves adaptive channel separation without altering the characteristics of the transmitter lights. This is especially advantageous in dual-use scenarios with illumination requirements. Additionally, external interferers, like natural light or transmitter light sources of neighboring cells in a multicell setting, can also be suppressed without requiring any control over them. Each user's LCD filter is placed in front of the corresponding photodetector and configured in such a way that only light from desired transmitters can reach the detector by setting only the appropriate pixels to transparent, while light from unwanted transmitters remains blocked. The effectiveness of this method is tested and benchmarked against zero-forcing (ZF) precoding in different scenarios and applications by numerical simulations and also verified experimentally in a large MIMO VLC testbed created specifically for this purpose

Joint Optimization of Illumination and Communication for a Multi-Element VLC Architecture

Because of the ever increasing demand wireless data in the modern era, the Radio Frequency (RF) spectrum is becoming more congested. The remaining RF spectrum is being shrunk at a very heavy rate, and spectral management is becoming more difficult. Mobile data is estimated to grow more than 10 times between 2013 and 2019, and due to this explosion in data usage, mobile operators are having serious concerns focusing on public Wireless Fidelity (Wi-Fi) and other alternative technologies. Visible Light Communication (VLC) is a recent promising technology complementary to RF spectrum which operates at the visible light spectrum band (roughly 400 THz to 780 THz) and it has 10,000 times bigger size than radio waves (roughly 3 kHz to 300 GHz). Due to this tremendous potential, VLC has captured a lot of interest recently as there is already an extensive deployment of energy efficient Light Emitting Diodes (LEDs). The advancements in LED technology with fast nanosecond switching times is also very encouraging. In this work, we present hybrid RF/VLC architecture which is capable of providing simultaneous lighting and communication coverage in an indoor setting. The architecture consists of a multi-element hemispherical bulb design, where it is possible to transmit multiple data streams from the multi-element hemispherical bulb using LED modules. We present the detailed components of the architecture and make simulations considering various VLC transmitter configurations. Also, we devise an approach for an efficient bulb design mechanism to maintain both illumination and communication at a satisfactory rate, and analyze it in the case of two users in a room. The approach involves formulating an optimization problem and tackling the problem using a simple partitioning algorithm. The results indicate that good link quality and high spatial reuse can be maintained in a typical indoor communication setting

Energy efficient visible light communications relying on amorphous cells

In this paper, we design an energy efficient indoor Visible Light Communications (VLC) system from a radically new perspective based on an amorphous user-to-network association structure. Explicitly, this intriguing problem is approached from three inter-linked perspectives, considering the cell formation, link-level transmission and system-level optimisation, critically appraising the related optical constraints. To elaborate, apart from proposing hitherto unexplored Amorphous Cells (A-Cells), we employ a powerful amalgam of Asymmetrically Clipped Optical Orthogonal Frequency Division Multiplexing (ACO-OFDM) and transmitter pre-coding aided Multi-Input Single-Output (MISO) transmission. As far as the overall systemlevel optimisation is concerned, we propose a low-complexity solution dispensing with the classic Dinkelbach’s algorithmic structure. Our numerical study compares a range of different cell formation strategies and investigates diverse design aspects of the proposed A-Cells. Specifically, our results show that the A-Cells proposed are capable of achieving a much higher energy efficiency per user compared to that of the conventional cell formation for a range of practical Field of Views (FoVs) angles

Hardware Architectures of Visible Light Communication Transmitter and Receiver for Beacon-based Indoor Positioning Systems

High-speed applications of Visible Light Communications have been presented recently in which response times of photodiode-based VLC receivers are critical points. Typical VLC receiver routines, such as soft-decoding of run-length limited (RLL) codes and FEC codes was purely processed on embedded firmware, and potentially cause bottleneck at the receiver. To speed up the performance of receivers, ASIC-based VLC receiver could be the solution. Unfortunately, recent works on soft-decoding of RLL and FEC have shown that they are bulky and time-consuming computations. This causes hardware implementation of VLC receivers becomes heavy and unrealistic. In this paper, we introduce a compact Polar-code-based VLC receivers. in which flicker mitigation of the system can be guaranteed even without RLL codes. In particular, we utilized the centralized bit-probability distribution of a pre-scrambler and a Polar encoder to create a non-RLL flicker mitigation solution. At the receiver, a 3-bit soft-decision filter was implemented to analyze signals received from the VLC channel to extract log-likelihood ratio (LLR) values and feed them to the Polar decoder. Therefore, the proposed receiver could exploit the soft-decoding of the Polar decoder to improve the error-correction performance of the system. Due to the non-RLL characteristic, the receiver has a preeminent code-rate and a reduced complexity compared with RLL-based receivers. We present the proposed VLC receiver along with a novel very-large-scale integration (VLSI) architecture, and a synthesis of our design using FPGA/ASIC synthesis tools