Mitigation of Side-Effect Modulation in Optical OFDM VLC Systems

Side-effect modulation (SEM) has the potential to be a significant source of interference in future visible light communication (VLC) systems. SEM is a variation in the intensity of the light emitted by a luminaire and is usually a side-effect caused by the power supply used to drive the luminaires. For LED luminaires powered by a switched mode power supply, the SEM can be at much higher frequencies than that emitted by conventional incandescent or fluorescent lighting. It has been shown that the SEM caused by commercially available LED luminaires is often periodic and of low power. In this paper, we investigate the impact of typical forms of SEM on the performance of optical OFDM VLC systems; both ACO-OFDM and DCO-OFDM are considered. Our results show that even low levels of SEM power can significantly degrade the bit-error-rate performance. To solve this problem, an SEM mitigation scheme is described. The mitigation scheme is decision-directed and is based on estimating and subtracting the fundamental component of the SEM from the received signal. We describe two forms of the algorithm; one uses blind estimation while the other uses pilot-assisted estimation based on a training sequence. Decision errors, resulting in decision noise, limit the performance of the blind estimator even when estimation is based on very long signals. However, the pilot system can achieve more accurate estimations, thus better performance. Results are first presented for typical SEM waveforms for the case where the fundamental frequency of the SEM is known. The algorithms are then extended to include a frequency estimation step and the mitigation algorithm is shown also to be effective in this case

Interference Suppression in Massive MIMO VLC Systems

The focus of this dissertation is on the development and evaluation of methods and principles to mitigate interference in multiuser visible light communication (VLC) systems using several transmitters. All components of such a massive multiple-input multiple-output (MIMO) system are considered and transformed into a communication system model, while also paying particular attention to the hardware requirements of different modulation schemes. By analyzing all steps in the communication process, the inter-channel interference between users is identified as the most critical aspect. Several methods of suppressing this kind of interference, i.e. to split the MIMO channel into parallel single channels, are discussed, and a novel active LCD-based interference suppression principle at the receiver side is introduced as main aspect of this work. This technique enables a dynamic adaption of the physical channel: compared to solely software-based or static approaches, the LCD interference suppression filter achieves adaptive channel separation without altering the characteristics of the transmitter lights. This is especially advantageous in dual-use scenarios with illumination requirements. Additionally, external interferers, like natural light or transmitter light sources of neighboring cells in a multicell setting, can also be suppressed without requiring any control over them. Each user's LCD filter is placed in front of the corresponding photodetector and configured in such a way that only light from desired transmitters can reach the detector by setting only the appropriate pixels to transparent, while light from unwanted transmitters remains blocked. The effectiveness of this method is tested and benchmarked against zero-forcing (ZF) precoding in different scenarios and applications by numerical simulations and also verified experimentally in a large MIMO VLC testbed created specifically for this purpose

Classification and modeling of power line noise using machine learning techniques

A thesis submitted in ful lment of the requirements for the degree of Doctor of Philosophy in the School of Electrical and Information Engineering Faculty of Engineering and Built Environment June 2017The realization of robust, reliable and e cient data transmission have been the theme of recent research, most importantly in real channel such as the noisy, fading prone power line communication (PLC) channel. The focus is to exploit old techniques or create new techniques capable of improving the transmission reliability and also increasing the transmission capacity of the real communication channels. Multi-carrier modulation scheme such as Orthogonal Frequency Division Multiplexing (OFDM) utilizing conventional single-carrier modulation is developed to facilitate a robust data transmission, increasing transmission capacity (e cient bandwidth usage) and further reducing design complexity in PLC systems. On the contrary, the reliability of data transmission is subjected to several inhibiting factors as a result of the varying nature of the PLC channel. These inhibiting factors include noise, perturbation and disturbances. Contrary to the Additive White Gaussian noise (AWGN) model often assumed in several communication systems, this noise model fails to capture the attributes of noise encountered on the PLC channel. This is because periodic noise or random noise pulses injected by power electronic appliances on the network is a deviation from the AWGN. The nature of the noise is categorized as non-white non-Gaussian and unstable due to its impulsive attributes, thus, it is labeled as Non-additive White Gaussian Noise (NAWGN). These noise and disturbances results into long burst errors that corrupts signals being transmitted, thus, the PLC is labeled as a horrible or burst error channel. The e cient and optimal performance of a conventional linear receiver in the white Gaussian noise environment can therefore be made to drastically degrade in this NAWGN environment. Therefore, transmission reliability in such environment can be greatly enhanced if we know and exploit the knowledge of the channel's statistical attributes, thus, the need for developing statistical channel model based on empirical data. In this thesis, attention is focused on developing a recon gurable software de ned un-coded single-carrier and multicarrier PLC transceiver as a tool for realizing an optimized channel model for the narrowband PLC (NB-PLC) channel. First, a novel recon gurable software de ned un-coded single-carrier and multi-carrier PLC transceiver is developed for real-time NB-PLC transmission. The transceivers can be adapted to implement di erent waveforms for several real-time scenarios and performance evaluation. Due to the varying noise parameters obtained from country to country as a result of the dependence of noise impairment on mains voltages, topology of power line, place and time, the developed transceivers is capable of facilitating constant measurement campaigns to capture these varying noise parameters before statistical and mathematically inclined channel models are derived. Furthermore, the single-carrier (Binary Phase Shift Keying (BPSK), Di erential BPSK (DBPSK), Quadrature Phase Shift Keying (QPSK) and Di erential QPSK (DQPSK)) PLC transceiver system developed is used to facilitate a First-Order semi-hidden Fritchman Markov modeling (SHFMM) of the NB-PLC channel utilizing the e cient iterative Baum- Welch algorithm (BWA) for parameter estimation. The performance of each modulation scheme is evaluated in a mildly and heavily disturbed scenarios for both residential and laboratory site considered. The First-Order estimated error statistics of the realized First- Order SHFMM have been analytically validated in terms of performance metrics such as: log-likelihood ratio (LLR), error-free run distribution (EFRD), error probabilities, mean square error (MSE) and Chi-square ( 2) test. The reliability of the model results is also con rmed by an excellent match between the empirically obtained error sequence and the SHFMM regenerated error sequence as shown by the error-free run distribution plot. This thesis also reports a novel development of a low cost, low complexity Frequency-shift keying (FSK) - On-o keying (OOK) in-house hybrid PLC and VLC system. The functionality of this hybrid PLC-VLC transceiver system was ascertained at both residential and laboratory site at three di erent times of the day: morning, afternoon and evening. A First and Second-Order SHFMM of the hybrid system is realized. The error statistics of the realized First and Second-Order SHFMMs have been analytically validated in terms of LLR, EFRD, error probabilities, MSE and Chi-square ( 2). The Second-Order SHFMMs have also been analytically validated to be superior to the First-Order SHFMMs although at the expense of added computational complexity. The reliability of both First and Second-Order SHFMM results is con rmed by an excellent match between the empirical error sequences and SHFMM re-generated error sequences as shown by the EFRD plot. In addition, the multi-carrier (QPSK-OFDM, Di erential QPSK (DQPSK)-OFDM) and Di erential 8-PSK (D8PSK)-OFDM) PLC transceiver system developed is used to facilitate a First and Second-Order modeling of the NB-PLC system using the SHFMM and BWA for parameter estimation. The performance of each OFDM modulation scheme in evaluated and compared taking into consideration the mildly and heavily disturbed noise scenarios for the two measurement sites considered. The estimated error statistics of the realized SHFMMs have been analytically validated in terms of LLR, EFRD, error probabilities, MSE and Chi-square ( 2) test. The estimated Second-Order SHFMMs have been analytically validated to be outperform the First-Order SHFMMs although with added computational complexity. The reliability of the models is con rmed by an excellent match between the empirical data and SHFMM generated data as shown by the EFRD plot. The statistical models obtained using Baum-Welch to adjust the parameters of the adopted SHFMM are often locally maximized. To solve this problem, a novel Metropolis-Hastings algorithm, a Bayesian inference approach based on Markov Chain Monte Carlo (MCMC) is developed to optimize the parameters of the adopted SHFMM. The algorithm is used to optimize the model results obtained from the single-carrier and multi-carrier PLC systems as well as that of the hybrid PLC-VLC system. Consequently, as deduced from the results, the models obtained utilizing the novel Metropolis-Hastings algorithm are more precise, near optimal model with parameter sets that are closer to the global maxima. Generally, the model results obtained in this thesis are relevant in enhancing transmission reliability on the PLC channel through the use of the models to improve the adopted modulation schemes, create adaptive modulation techniques, develop and evaluate forward error correction (FEC) codes such as a concatenation of Reed-Solomon and Permutation codes and other robust codes suitable for exploiting and mitigating noise impairments encountered on the low voltage NB-PLC channel. Furthermore, the recon gurable software de ned NB-PLC transceiver test-bed developed can be utilized for future measurement campaign as well as adapted for multiple-input and multiple-output (MIMO) PLC applications.MT201

Classification and modeling of power line noise using machine learning techniques

A thesis submitted in ful lment of the requirements for the degree of Doctor of Philosophy in the School of Electrical and Information Engineering Faculty of Engineering and Built Environment June 2017The realization of robust, reliable and e cient data transmission have been the theme of recent research, most importantly in real channel such as the noisy, fading prone power line communication (PLC) channel. The focus is to exploit old techniques or create new techniques capable of improving the transmission reliability and also increasing the transmission capacity of the real communication channels. Multi-carrier modulation scheme such as Orthogonal Frequency Division Multiplexing (OFDM) utilizing conventional single-carrier modulation is developed to facilitate a robust data transmission, increasing transmission capacity (e cient bandwidth usage) and further reducing design complexity in PLC systems. On the contrary, the reliability of data transmission is subjected to several inhibiting factors as a result of the varying nature of the PLC channel. These inhibiting factors include noise, perturbation and disturbances. Contrary to the Additive White Gaussian noise (AWGN) model often assumed in several communication systems, this noise model fails to capture the attributes of noise encountered on the PLC channel. This is because periodic noise or random noise pulses injected by power electronic appliances on the network is a deviation from the AWGN. The nature of the noise is categorized as non-white non-Gaussian and unstable due to its impulsive attributes, thus, it is labeled as Non-additive White Gaussian Noise (NAWGN). These noise and disturbances results into long burst errors that corrupts signals being transmitted, thus, the PLC is labeled as a horrible or burst error channel. The e cient and optimal performance of a conventional linear receiver in the white Gaussian noise environment can therefore be made to drastically degrade in this NAWGN environment. Therefore, transmission reliability in such environment can be greatly enhanced if we know and exploit the knowledge of the channel's statistical attributes, thus, the need for developing statistical channel model based on empirical data. In this thesis, attention is focused on developing a recon gurable software de ned un-coded single-carrier and multicarrier PLC transceiver as a tool for realizing an optimized channel model for the narrowband PLC (NB-PLC) channel. First, a novel recon gurable software de ned un-coded single-carrier and multi-carrier PLC transceiver is developed for real-time NB-PLC transmission. The transceivers can be adapted to implement di erent waveforms for several real-time scenarios and performance evaluation. Due to the varying noise parameters obtained from country to country as a result of the dependence of noise impairment on mains voltages, topology of power line, place and time, the developed transceivers is capable of facilitating constant measurement campaigns to capture these varying noise parameters before statistical and mathematically inclined channel models are derived. Furthermore, the single-carrier (Binary Phase Shift Keying (BPSK), Di erential BPSK (DBPSK), Quadrature Phase Shift Keying (QPSK) and Di erential QPSK (DQPSK)) PLC transceiver system developed is used to facilitate a First-Order semi-hidden Fritchman Markov modeling (SHFMM) of the NB-PLC channel utilizing the e cient iterative Baum- Welch algorithm (BWA) for parameter estimation. The performance of each modulation scheme is evaluated in a mildly and heavily disturbed scenarios for both residential and laboratory site considered. The First-Order estimated error statistics of the realized First- Order SHFMM have been analytically validated in terms of performance metrics such as: log-likelihood ratio (LLR), error-free run distribution (EFRD), error probabilities, mean square error (MSE) and Chi-square ( 2) test. The reliability of the model results is also con rmed by an excellent match between the empirically obtained error sequence and the SHFMM regenerated error sequence as shown by the error-free run distribution plot. This thesis also reports a novel development of a low cost, low complexity Frequency-shift keying (FSK) - On-o keying (OOK) in-house hybrid PLC and VLC system. The functionality of this hybrid PLC-VLC transceiver system was ascertained at both residential and laboratory site at three di erent times of the day: morning, afternoon and evening. A First and Second-Order SHFMM of the hybrid system is realized. The error statistics of the realized First and Second-Order SHFMMs have been analytically validated in terms of LLR, EFRD, error probabilities, MSE and Chi-square ( 2). The Second-Order SHFMMs have also been analytically validated to be superior to the First-Order SHFMMs although at the expense of added computational complexity. The reliability of both First and Second-Order SHFMM results is con rmed by an excellent match between the empirical error sequences and SHFMM re-generated error sequences as shown by the EFRD plot. In addition, the multi-carrier (QPSK-OFDM, Di erential QPSK (DQPSK)-OFDM) and Di erential 8-PSK (D8PSK)-OFDM) PLC transceiver system developed is used to facilitate a First and Second-Order modeling of the NB-PLC system using the SHFMM and BWA for parameter estimation. The performance of each OFDM modulation scheme in evaluated and compared taking into consideration the mildly and heavily disturbed noise scenarios for the two measurement sites considered. The estimated error statistics of the realized SHFMMs have been analytically validated in terms of LLR, EFRD, error probabilities, MSE and Chi-square ( 2) test. The estimated Second-Order SHFMMs have been analytically validated to be outperform the First-Order SHFMMs although with added computational complexity. The reliability of the models is con rmed by an excellent match between the empirical data and SHFMM generated data as shown by the EFRD plot. The statistical models obtained using Baum-Welch to adjust the parameters of the adopted SHFMM are often locally maximized. To solve this problem, a novel Metropolis-Hastings algorithm, a Bayesian inference approach based on Markov Chain Monte Carlo (MCMC) is developed to optimize the parameters of the adopted SHFMM. The algorithm is used to optimize the model results obtained from the single-carrier and multi-carrier PLC systems as well as that of the hybrid PLC-VLC system. Consequently, as deduced from the results, the models obtained utilizing the novel Metropolis-Hastings algorithm are more precise, near optimal model with parameter sets that are closer to the global maxima. Generally, the model results obtained in this thesis are relevant in enhancing transmission reliability on the PLC channel through the use of the models to improve the adopted modulation schemes, create adaptive modulation techniques, develop and evaluate forward error correction (FEC) codes such as a concatenation of Reed-Solomon and Permutation codes and other robust codes suitable for exploiting and mitigating noise impairments encountered on the low voltage NB-PLC channel. Furthermore, the recon gurable software de ned NB-PLC transceiver test-bed developed can be utilized for future measurement campaign as well as adapted for multiple-input and multiple-output (MIMO) PLC applications.MT201

Heterogeneous integration of optical wireless communications within next generation networks

Unprecedented traffic growth is expected in future wireless networks and new technologies will be needed to satisfy demand. Optical wireless (OW) communication offers vast unused spectrum and high area spectral efficiency. In this work, optical cells are envisioned as supplementary access points within heterogeneous RF/OW networks. These networks opportunistically offload traffic to optical cells while utilizing the RF cell for highly mobile devices and devices that lack a reliable OW connection. Visible light communication (VLC) is considered as a potential OW technology due to the increasing adoption of solid state lighting for indoor illumination. Results of this work focus on a full system view of RF/OW HetNets with three primary areas of analysis. First, the need for network densication beyond current RF small cell implementations is evaluated. A media independent model is developed and results are presented that provide motivation for the adoption of hyper dense small cells as complementary components within multi-tier networks. Next, the relationships between RF and OW constraints and link characterization parameters are evaluated in order to define methods for fair comparison when user-centric channel selection criteria are used. RF and OW noise and interference characterization techniques are compared and common OW characterization models are demonstrated to show errors in excess of 100x when dominant interferers are present. Finally, dynamic characteristics of hyper dense OW networks are investigated in order to optimize traffic distribution from a network-centric perspective. A Kalman Filter model is presented to predict device motion for improved channel selection and a novel OW range expansion technique is presented that dynamically alters coverage regions of OW cells by 50%. In addition to analytical results, the dissertation describes two tools that have been created for evaluation of RF/OW HetNets. A communication and lighting simulation toolkit has been developed for modeling and evaluation of environments with VLC-enabled luminaires. The toolkit enhances an iterative site based impulse response simulator model to utilize GPU acceleration and achieves 10x speedup over the previous model. A software defined testbed for OW has also been proposed and applied. The testbed implements a VLC link and a heterogeneous RF/VLC connection that demonstrates the RF/OW HetNet concept as proof of concept

Fifty Years of Noise Modeling and Mitigation in Power-Line Communications.

Building on the ubiquity of electric power infrastructure, power line communications (PLC) has been successfully used in diverse application scenarios, including the smart grid and in-home broadband communications systems as well as industrial and home automation. However, the power line channel exhibits deleterious properties, one of which is its hostile noise environment. This article aims for providing a review of noise modeling and mitigation techniques in PLC. Specifically, a comprehensive review of representative noise models developed over the past fifty years is presented, including both the empirical models based on measurement campaigns and simplified mathematical models. Following this, we provide an extensive survey of the suite of noise mitigation schemes, categorizing them into mitigation at the transmitter as well as parametric and non-parametric techniques employed at the receiver. Furthermore, since the accuracy of channel estimation in PLC is affected by noise, we review the literature of joint noise mitigation and channel estimation solutions. Finally, a number of directions are outlined for future research on both noise modeling and mitigation in PLC

Optics for AI and AI for Optics

Artificial intelligence is deeply involved in our daily lives via reinforcing the digital transformation of modern economies and infrastructure. It relies on powerful computing clusters, which face bottlenecks of power consumption for both data transmission and intensive computing. Meanwhile, optics (especially optical communications, which underpin today’s telecommunications) is penetrating short-reach connections down to the chip level, thus meeting with AI technology and creating numerous opportunities. This book is about the marriage of optics and AI and how each part can benefit from the other. Optics facilitates on-chip neural networks based on fast optical computing and energy-efficient interconnects and communications. On the other hand, AI enables efficient tools to address the challenges of today’s optical communication networks, which behave in an increasingly complex manner. The book collects contributions from pioneering researchers from both academy and industry to discuss the challenges and solutions in each of the respective fields

Contextually and identity aware 5G services

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University LondonThe fifth generation (5G) mobile networks aim to be ten times faster than the existing 4G connection, whilst providing low latency, and flexibility. Hence, various alterations are planned to the existing network infrastructure to be able to reach the 5G expected performance levels. The main technologies that were used, to ensure high performance, flexible network, and efficient resource allocation, are Software Defined Network and Network Function Virtualization. As these technologies are replacing the device-based architecture with, a service-based architecture. This thesis provides a design of location database interactive web interface and interactive mobile application. The implementation of real time video streaming location server, the streaming system's performance parameters demonstrated a high level of QoS (0.07ms jitter and 9.53ms delay). In regard to experimental examination, it measured the localisation coverage, accuracy measurements and a highly scalable security solution. The localisation coverage and accuracy measurements were achieved through the mmWave and VLC link transmitters. The proposed simulated annealing algorithm aimed at data optimisation for location measurements accuracy showed results of the average location error of x and y which showed significant improvement from x= 22.5 and y=21.6 to x=11.09 and y= 11.63. The proposed indoor location security solution showed significant results, as it provides a high scalability solution using the VNF. The solution showed that it was not 100% effective, as some of the fake discover packets still reached the DHCP server. This was due to the high load of traffic passing through the network. Nonetheless, 90% of the fake DHCP discover packets never reached the DHCP server because the scripts began blocking all fake discover packets after realising it was an attack. This conveys that the proposed system was able to run successfully without crashing or overloading the controller. Overall, the main challenges facing 5G have been addressed with their proposed solutions, which showed promising results. Conclusively showing that there is a lot more space for technological advancements to support the future of mobile networks.European Union’s Horizon 2020 research program - the Internet of Radio-Light (IoRL) project H2020-ICT 761992

Interference mitigation in LiFi networks

Due to the increasing demand for wireless data, the radio frequency (RF) spectrum has become a very limited resource. Alternative approaches are under investigation to support the future growth in data traffic and next-generation high-speed wireless communication systems. Techniques such as massive multiple-input multiple-output (MIMO), millimeter wave (mmWave) communications and light-fidelity (LiFi) are being explored. Among these technologies, LiFi is a novel bi-directional, high-speed and fully networked wireless communication technology. However, inter-cell interference (ICI) can significantly restrict the system performance of LiFi attocell networks. This thesis focuses on interference mitigation in LiFi attocell networks. The angle diversity receiver (ADR) is one solution to address the issue of ICI as well as frequency reuse in LiFi attocell networks. With the property of high concentration gain and narrow field of view (FOV), the ADR is very beneficial for interference mitigation. However, the optimum structure of the ADR has not been investigated. This motivates us to propose the optimum structures for the ADRs in order to fully exploit the performance gain. The impact of random device orientation and diffuse link signal propagation are taken into consideration. The performance comparison between the select best combining (SBC) and maximum ratio combining (MRC) is carried out under different noise levels. In addition, the double source (DS) system, where each LiFi access point (AP) consists of two sources transmitting the same information signals but with opposite polarity, is proven to outperform the single source (SS) system under certain conditions. Then, to overcome issues around ICI, random device orientation and link blockage, hybrid LiFi/WiFi networks (HLWNs) are considered. In this thesis, dynamic load balancing (LB) considering handover in HLWNs is studied. The orientation-based random waypoint (ORWP) mobility model is considered to provide a more realistic framework to evaluate the performance of HLWNs. Based on the low-pass filtering effect of the LiFi channel, we firstly propose an orthogonal frequency division multiple access (OFDMA)-based resource allocation (RA) method in LiFi systems. Also, an enhanced evolutionary game theory (EGT)-based LB scheme with handover in HLWNs is proposed. Finally, due to the characteristic of high directivity and narrow beams, a vertical-cavity surface-emitting laser (VCSEL) array transmission system has been proposed to mitigate ICI. In order to support mobile users, two beam activation methods are proposed. The beam activation based on the corner-cube retroreflector (CCR) can achieve low power consumption and almost-zero delay, allowing real-time beam activation for high-speed users. The mechanism based on the omnidirectional transmitter (ODTx) is suitable for low-speed users and very robust to random orientation