98 research outputs found

    Semi-automated geomorphological mapping applied to landslide hazard analysis

    Get PDF
    Computer-assisted three-dimensional (3D) mapping using stereo and multi-image (“softcopy”) photogrammetry is shown to enhance the visual interpretation of geomorphology in steep terrain with the direct benefit of greater locational accuracy than traditional manual mapping. This would benefit multi-parameter correlations between terrain attributes and landslide distribution in both direct and indirect forms of landslide hazard assessment. Case studies involve synthetic models of a landslide, and field studies of a rock slope and steep undeveloped hillsides with both recently formed and partly degraded, old landslide scars. Diagnostic 3D morphology was generated semi-automatically both using a terrain-following cursor under stereo-viewing and from high resolution digital elevation models created using area-based image correlation, further processed with curvature algorithms. Laboratory-based studies quantify limitations of area-based image correlation for measurement of 3D points on planar surfaces with varying camera orientations. The accuracy of point measurement is shown to be non-linear with limiting conditions created by both narrow and wide camera angles and moderate obliquity of the target plane. Analysis of the results with the planar surface highlighted problems with the controlling parameters of the area-based image correlation process when used for generating DEMs from images obtained with a low-cost digital camera. Although the specific cause of the phase-wrapped image artefacts identified was not found, the procedure would form a suitable method for testing image correlation software, as these artefacts may not be obvious in DEMs of non-planar surfaces.Modelling of synthetic landslides shows that Fast Fourier Transforms are an efficient method for removing noise, as produced by errors in measurement of individual DEM points, enabling diagnostic morphological terrain elements to be extracted. Component landforms within landslides are complex entities and conversion of the automatically-defined morphology into geomorphology was only achieved with manual interpretation; however, this interpretation was facilitated by softcopy-driven stereo viewing of the morphological entities across the hillsides.In the final case study of a large landslide within a man-made slope, landslide displacements were measured using a photogrammetric model consisting of 79 images captured with a helicopter-borne, hand-held, small format digital camera. Displacement vectors and a thematic geomorphological map were superimposed over an animated, 3D photo-textured model to aid non-stereo visualisation and communication of results

    Validation of close-range photogrammetry for architectural and archaeological heritage Analysis of point density and 3D mesh geometry

    Get PDF
    The 3D digitization and Building Information Modeling (BIM), which is based on parametric objects, have considerably advanced by developing massive data capture techniques. Thus, reverse engineering currently plays a major role as these technologies capture accurately and efficiently the geometry, color and textures of complex architectural, archaeological and cultural heritage. This paper aims to validate close-range Structure from Motion (SfM) for heritage by analyzing the point density and the 3D mesh geometry in comparison with Terrestrial Laser Scanning (TLS). The accuracy of the results and the geometry mainly depends on the processing performed on the point set. Therefore, these two variables are significant in the 3D reconstruction of heritage buildings. This paper focuses on a 15th century case study in Seville (Spain): the main façade of Casa de Pilatos. Ten SfM surveys were carried out varying the capture method (simple and stereoscopic) and the number of shots, distances, orientation and procedure. A mathematical analysis is proposed to verify the point spatial resolution and the accuracy of the 3D model geometry by section profiles in SfM data. SfM achieved acceptable accuracy levels to generate 3D meshes despite disordered shots and the number of images. Hence, stereoscopic photography using new instruments improved the results of close-range photogrammetry while reducing the required number of photographs

    Context-based urban terrain reconstruction from uav-videos for geoinformation applications

    Get PDF
    Urban terrain reconstruction has many applications in areas of civil engineering, urban planning, surveillance and defense research. Therefore the needs of covering ad-hoc demand and performing a close-range urban terrain reconstruction with miniaturized and relatively inexpensive sensor platforms are constantly growing. Using (miniaturized) unmanned aerial vehicles, (M) UAVs, represents one of the most attractive alternatives to conventional large-scale aerial imagery. We cover in this paper a four-step procedure of obtaining georeferenced 3D urban models from video sequences. The four steps of the procedure - orientation, dense reconstruction, urban terrain modeling and geo-referencing - are robust, straight-forward, and nearly fully-automatic. The two last steps - namely, urban terrain modeling from almost-nadir videos and co-registration of models - represent the main contribution of this work and will therefore be covered with more detail. The essential substeps of the third step include digital terrain model (DTM) extraction, segregation of buildings from vegetation, as well as instantiation of building and tree models. The last step is subdivided into quasi-intrasensorial registration of Euclidean reconstructions and intersensorial registration with a geo-referenced orthophoto. Finally, we present reconstruction results from a real data-set and outline ideas for future work

    3-D uncertainty-based topographic change detection with structure-from-motion photogrammetry: precision maps for ground control and directly georeferenced surveys

    Get PDF
    Structure-from-motion (SfM) photogrammetry is revolutionising the collection of detailed topographic data, but insight into geomorphological processes is currently restricted by our limited understanding of SfM survey uncertainties. Here, we present an approach that, for the first time, specifically accounts for the spatially variable precision inherent to photo-based surveys, and enables confidence-bounded quantification of 3-D topographic change. The method uses novel 3-D precision maps that describe the 3-D photogrammetric and georeferencing uncertainty, and determines change through an adapted state-of-the-art fully 3-D point-cloud comparison (M3C2; Lague, et al., 2013), which is particularly valuable for complex topography. We introduce this method by: (1) using simulated UAV surveys, processed in photogrammetric software, to illustrate the spatial variability of precision and the relative influences of photogrammetric (e.g. image network geometry, tie point quality) and georeferencing (e.g. control measurement) considerations; (2) we then present a new Monte Carlo procedure for deriving this information using standard SfM software and integrate it into confidence-bounded change detection; before (3) demonstrating geomorphological application in which we use benchmark TLS data for validation and then estimate sediment budgets through differencing annual SfM surveys of an eroding badland. We show how 3-D precision maps enable more probable erosion patterns to be identified than existing analyses, and how a similar overall survey precision could have been achieved with direct survey georeferencing for camera position data with precision half as good as the GCPs’. Where precision is limited by weak georeferencing (e.g. camera positions with multi-metre precision, such as from a consumer UAV), then overall survey precision can scale as n-½ of the control precision (n = number of images). Our method also provides variance-covariance information for all parameters. Thus, we now open the door for SfM practitioners to use the comprehensive analyses that have underpinned rigorous photogrammetric approaches over the last half-century

    Map-Based Localization for Unmanned Aerial Vehicle Navigation

    Get PDF
    Unmanned Aerial Vehicles (UAVs) require precise pose estimation when navigating in indoor and GNSS-denied / GNSS-degraded outdoor environments. The possibility of crashing in these environments is high, as spaces are confined, with many moving obstacles. There are many solutions for localization in GNSS-denied environments, and many different technologies are used. Common solutions involve setting up or using existing infrastructure, such as beacons, Wi-Fi, or surveyed targets. These solutions were avoided because the cost should be proportional to the number of users, not the coverage area. Heavy and expensive sensors, for example a high-end IMU, were also avoided. Given these requirements, a camera-based localization solution was selected for the sensor pose estimation. Several camera-based localization approaches were investigated. Map-based localization methods were shown to be the most efficient because they close loops using a pre-existing map, thus the amount of data and the amount of time spent collecting data are reduced as there is no need to re-observe the same areas multiple times. This dissertation proposes a solution to address the task of fully localizing a monocular camera onboard a UAV with respect to a known environment (i.e., it is assumed that a 3D model of the environment is available) for the purpose of navigation for UAVs in structured environments. Incremental map-based localization involves tracking a map through an image sequence. When the map is a 3D model, this task is referred to as model-based tracking. A by-product of the tracker is the relative 3D pose (position and orientation) between the camera and the object being tracked. State-of-the-art solutions advocate that tracking geometry is more robust than tracking image texture because edges are more invariant to changes in object appearance and lighting. However, model-based trackers have been limited to tracking small simple objects in small environments. An assessment was performed in tracking larger, more complex building models, in larger environments. A state-of-the art model-based tracker called ViSP (Visual Servoing Platform) was applied in tracking outdoor and indoor buildings using a UAVs low-cost camera. The assessment revealed weaknesses at large scales. Specifically, ViSP failed when tracking was lost, and needed to be manually re-initialized. Failure occurred when there was a lack of model features in the cameras field of view, and because of rapid camera motion. Experiments revealed that ViSP achieved positional accuracies similar to single point positioning solutions obtained from single-frequency (L1) GPS observations standard deviations around 10 metres. These errors were considered to be large, considering the geometric accuracy of the 3D model used in the experiments was 10 to 40 cm. The first contribution of this dissertation proposes to increase the performance of the localization system by combining ViSP with map-building incremental localization, also referred to as simultaneous localization and mapping (SLAM). Experimental results in both indoor and outdoor environments show sub-metre positional accuracies were achieved, while reducing the number of tracking losses throughout the image sequence. It is shown that by integrating model-based tracking with SLAM, not only does SLAM improve model tracking performance, but the model-based tracker alleviates the computational expense of SLAMs loop closing procedure to improve runtime performance. Experiments also revealed that ViSP was unable to handle occlusions when a complete 3D building model was used, resulting in large errors in its pose estimates. The second contribution of this dissertation is a novel map-based incremental localization algorithm that improves tracking performance, and increases pose estimation accuracies from ViSP. The novelty of this algorithm is the implementation of an efficient matching process that identifies corresponding linear features from the UAVs RGB image data and a large, complex, and untextured 3D model. The proposed model-based tracker improved positional accuracies from 10 m (obtained with ViSP) to 46 cm in outdoor environments, and improved from an unattainable result using VISP to 2 cm positional accuracies in large indoor environments. The main disadvantage of any incremental algorithm is that it requires the camera pose of the first frame. Initialization is often a manual process. The third contribution of this dissertation is a map-based absolute localization algorithm that automatically estimates the camera pose when no prior pose information is available. The method benefits from vertical line matching to accomplish a registration procedure of the reference model views with a set of initial input images via geometric hashing. Results demonstrate that sub-metre positional accuracies were achieved and a proposed enhancement of conventional geometric hashing produced more correct matches - 75% of the correct matches were identified, compared to 11%. Further the number of incorrect matches was reduced by 80%

    Refined Equivalent Pinhole Model for Large-scale 3D Reconstruction from Spaceborne CCD Imagery

    Full text link
    In this study, we present a large-scale earth surface reconstruction pipeline for linear-array charge-coupled device (CCD) satellite imagery. While mainstream satellite image-based reconstruction approaches perform exceptionally well, the rational functional model (RFM) is subject to several limitations. For example, the RFM has no rigorous physical interpretation and differs significantly from the pinhole imaging model; hence, it cannot be directly applied to learning-based 3D reconstruction networks and to more novel reconstruction pipelines in computer vision. Hence, in this study, we introduce a method in which the RFM is equivalent to the pinhole camera model (PCM), meaning that the internal and external parameters of the pinhole camera are used instead of the rational polynomial coefficient parameters. We then derive an error formula for this equivalent pinhole model for the first time, demonstrating the influence of the image size on the accuracy of the reconstruction. In addition, we propose a polynomial image refinement model that minimizes equivalent errors via the least squares method. The experiments were conducted using four image datasets: WHU-TLC, DFC2019, ISPRS-ZY3, and GF7. The results demonstrated that the reconstruction accuracy was proportional to the image size. Our polynomial image refinement model significantly enhanced the accuracy and completeness of the reconstruction, and achieved more significant improvements for larger-scale images.Comment: 24 page

    UAV LINEAR PHOTOGRAMMETRY

    Get PDF

    UAV-BASED POINT CLOUD GENERATION FOR OPEN-PIT MINE MODELLING

    Get PDF

    Metric aspects of reconnaissance frame photography

    Get PDF
    No abstract available
    corecore