7,295 research outputs found
Using LES to Study Reacting Flows and Instabilities in Annular Combustion Chambers
Great prominence is put on the design of aeronautical gas turbines due to increasingly stringent regulations and the need to tackle rising fuel prices. This drive towards innovation has resulted sometimes in new concepts being prone to combustion instabilities. In the particular field of annular combustion chambers, these instabilities often take the form of azimuthal modes. To predict these modes, one must compute the full combustion chamber, which remained out of reach until very recently and the development of massively parallel computers. Since one of the most limiting factors in performing Large Eddy Simulation (LES) of real combustors is estimating the adequate grid, the effects of mesh resolution are investigated by computing full annular LES of a realistic helicopter combustion chamber on three grids, respectively made of 38, 93 and 336 million elements. Results are compared in terms of mean and fluctuating fields. LES captures self-established azimuthal modes. The presence and structure of the modes is discussed. This study therefore highlights the potential of LES for studying combustion instabilities in annular gas turbine combustors
Cluster-based feedback control of turbulent post-stall separated flows
We propose a novel model-free self-learning cluster-based control strategy
for general nonlinear feedback flow control technique, benchmarked for
high-fidelity simulations of post-stall separated flows over an airfoil. The
present approach partitions the flow trajectories (force measurements) into
clusters, which correspond to characteristic coarse-grained phases in a
low-dimensional feature space. A feedback control law is then sought for each
cluster state through iterative evaluation and downhill simplex search to
minimize power consumption in flight. Unsupervised clustering of the flow
trajectories for in-situ learning and optimization of coarse-grained control
laws are implemented in an automated manner as key enablers. Re-routing the
flow trajectories, the optimized control laws shift the cluster populations to
the aerodynamically favorable states. Utilizing limited number of sensor
measurements for both clustering and optimization, these feedback laws were
determined in only iterations. The objective of the present work is not
necessarily to suppress flow separation but to minimize the desired cost
function to achieve enhanced aerodynamic performance. The present control
approach is applied to the control of two and three-dimensional separated flows
over a NACA 0012 airfoil with large-eddy simulations at an angle of attack of
, Reynolds number and free-stream Mach number . The optimized control laws effectively minimize the flight power
consumption enabling the flows to reach a low-drag state. The present work aims
to address the challenges associated with adaptive feedback control design for
turbulent separated flows at moderate Reynolds number.Comment: 32 pages, 18 figure
Unsteady cfd analysis of erosion mechanism in the coolant channels of a rotating gas turbine blade
The two-phase flow in a rotating wedge mimicking the final portion of a blade turbine internal cooling channel is here presented and discussed focusing on unsteady motion and erosion mechanisms. The rotation axis is placed to properly reproduce a configuration with a very strong deviation (90°).
The flow field was modelled by using the well known k---f unsteady-RANS model based on the elliptic-relaxation concept. The model was modified by some of the authors to take into account the influence of turbulence anisotropy as well as rotation. The model was applied to the well-established and fully validated T-FlowS code.
A systematic comparison of rotating and non-rotating case was carried out to show the influence of Coriolis force on flow and erosion mechanisms.
The rotational effects strongly changed the flow behaviour within the channel, affecting both the unsteady flow and the particles trajectories. In the rotating case, there is no recirculation on the tip region; besides, position of the small recirculation regions above each pedestals change. These, and other minor effects, affect the particle motion thus resulting in a different erosion pattern
Three-dimensional turbopump flowfield analysis
A program was conducted to develop a flow prediction method applicable to rocket turbopumps. The complex nature of a flowfield in turbopumps is described and examples of flowfields are discussed to illustrate that physics based models and analytical calculation procedures based on computational fluid dynamics (CFD) are needed to develop reliable design procedures for turbopumps. A CFD code developed at NASA ARC was used as the base code. The turbulence model and boundary conditions in the base code were modified, respectively, to: (1) compute transitional flows and account for extra rates of strain, e.g., rotation; and (2) compute surface heat transfer coefficients and allow computation through multistage turbomachines. Benchmark quality data from two and three-dimensional cascades were used to verify the code. The predictive capabilities of the present CFD code were demonstrated by computing the flow through a radial impeller and a multistage axial flow turbine. Results of the program indicate that the present code operated in a two-dimensional mode is a cost effective alternative to full three-dimensional calculations, and that it permits realistic predictions of unsteady loadings and losses for multistage machines
Heat transfer in aeropropulsion systems
Aeropropulsion heat transfer is reviewed. A research methodology based on a growing synergism between computations and experiments is examined. The aeropropulsion heat transfer arena is identified as high Reynolds number forced convection in a highly disturbed environment subject to strong gradients, body forces, abrupt geometry changes and high three dimensionality - all in an unsteady flow field. Numerous examples based on heat transfer to the aircraft gas turbine blade are presented to illustrate the types of heat transfer problems which are generic to aeropropulsion systems. The research focus of the near future in aeropropulsion heat transfer is projected
Aeronautical Engineering: A special bibliography with indexes, supplement 72, July 1976
This bibliography lists 184 reports, articles, and other documents introduced into the NASA scientific and technical information system in June 1976
Reynolds number influences in aeronautics
Reynolds number, a measure of the ratio of inertia to viscous forces, is a fundamental similarity parameter for fluid flows and therefore, would be expected to have a major influence in aerodynamics and aeronautics. Reynolds number influences are generally large, but monatomic, for attached laminar (continuum) flow; however, laminar flows are easily separated, inducing even stronger, non-monatomic, Reynolds number sensitivities. Probably the strongest Reynolds number influences occur in connection with transitional flow behavior. Transition can take place over a tremendous Reynolds number range, from the order of 20 x 10(exp 3) for 2-D free shear layers up to the order of 100 x 10(exp 6) for hypersonic boundary layers. This variability in transition behavior is especially important for complex configurations where various vehicle and flow field elements can undergo transition at various Reynolds numbers, causing often surprising changes in aerodynamics characteristics over wide ranges in Reynolds number. This is further compounded by the vast parameterization associated with transition, in that any parameter which influences mean viscous flow development (e.g., pressure gradient, flow curvature, wall temperature, Mach number, sweep, roughness, flow chemistry, shock interactions, etc.), and incident disturbance fields (acoustics, vorticity, particulates, temperature spottiness, even electro static discharges) can alter transition locations to first order. The usual method of dealing with the transition problem is to trip the flow in the generally lower Reynolds number wind tunnel to simulate the flight turbulent behavior. However, this is not wholly satisfactory as it results in incorrectly scaled viscous region thicknesses and cannot be utilized at all for applications such as turbine blades and helicopter rotors, nacelles, leading edge and nose regions, and High Altitude Long Endurance and hypersonic airbreathers where the transitional flow is an innately critical portion of the problem
- …