101 research outputs found
Analysis and design of wideband voltage controlled oscillators using self-oscillating active inductors.
Voltage controlled oscillators (VCOs) are essential components of RF circuits used in
transmitters and receivers as sources of carrier waves with variable frequencies. This, together
with a rapid development of microelectronic circuits, led to an extensive research
on integrated implementations of the oscillator circuits. One of the known approaches
to oscillator design employs resonators with active inductors electronic circuits simulating
the behavior of passive inductors using only transistors and capacitors. Such
resonators occupy only a fraction of the silicon area necessary for a passive inductor,
and thus allow to use chip area more eectively. The downsides of the active inductor
approach include: power consumption and noise introduced by transistors.
This thesis presents a new approach to active inductor oscillator design using selfoscillating
active inductor circuits. The instability necessary to start oscillations is
provided by the use of a passive RC network rather than a power consuming external
circuit employed in the standard oscillator approach. As a result, total power consumption
of the oscillator is improved. Although, some of the active inductors with
RC circuits has been reported in the literature, there has been no attempt to utilise
this technique in wideband voltage controlled oscillator design. For this reason, the
dissertation presents a thorough investigation of self-oscillating active inductor circuits,
providing a new set of design rules and related trade-os. This includes: a complete
small signal model of the oscillator, sensitivity analysis, large signal behavior of the circuit
and phase noise model. The presented theory is conrmed by extensive simulations
of wideband CMOS VCO circuit for various temperatures and process variations. The obtained results prove that active inductor oscillator performance is obtained without
the use of standard active compensation circuits. Finally, the concept of self-oscillating
active inductor has been employed to simple and fast OOK (On-Off Keying) transmitter
showing energy eciency comparable to the state of the art implementations reported
in the literature
High Performance Tunable Active Inductors For Microwave Circuits
Tez (Doktora) -- İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, 2016Thesis (PhD) -- İstanbul Technical University, Institute of Science and Technology, 2016RF uygulamalarında enduktif karakteristiğe önemli ölçüde ihtiyaç duyulmaktadır; bunlar, özellikle filtreler, düşük gürültülü yükselteçler (LNA, low noise amplifiers), gerilim kontrollü osilatörler (VCO, voltage controlled oscillators), pek çok farklı türde yükselteç için band genişliği iyileştirilmesi, faz kaydırıcılar, güç bölücüler ve eşleştirme (matching) devreleri vb. uygulamalardır. Pasif sarmal çip-içi CMOS endüktansların eksik yönleri ayrıntılı olarak literatürde tartışılmıştır. Bu tür endüktanslar düşük değer katsayısı (quality factor), düşük öz-rezonans frekansı (SRF, self-resonance frequency), sabit ve düşük değerli endüktans ve geniş bir silikon (silicon) alanı gerektirmeleri gibi istenmeyen özelliklere sahiptirler. Diğer yandan, MOS transistorlar kullanılarak sentezlenen CMOS aktif endüktansların, pasif sarmal eşdeğer yapıları ile karşılaştırıldığında pek çok çekici karakteristik özellik sunabildikleri gösterilmiştir. Bunlar; geniş bir bölgede ayarlanabilir öz-rezonans frekansı başarımı, geniş bir bölgede ayarlanabilir endüktans başarımı, geniş bir bölgede ayarlanabilir değer katsayısı başarımı, CMOS teknolojileri ile tümüyle gerçeklenebilme ve az alan kaplama gibi karakteristik özellikleri olarak ortaya konulmaktadır. Literatürde jiratör-C (GC) prensibi, topolojisi, karakterizasyonu ve uygulamaları ayrıntılı olarak ele alınmaktadır. İşlemsel geçiş-iletkenliği kuvvetlendiricisi (OTA, operational transconductance amplifier) ile gerçeklenen GC devreleri, RF uygulamaları için oldukça uygundur. Bu özellik, GC yapılarının söz konusu yapı kullanılarak en az sayıda aktif eleman ile gerçeklenebilmesinden kaynaklanmaktadır. Gerek topraklı (grounded) gerekse yüzen (floating) aktif endüktansların GC devreleri ile gerçeklenebildiği gösterilmiştir. Aktif endüktansların başarımlarının nicel olarak ölçülmesi amacıyla, çok sayıda ölçüt ortaya konulmuştur. Bu ölçütler frekans çalışma aralığı, endüktans ayarlanabilirliği, değer katsayısı, gürültü ve güç tüketimi gibi temel özellikleri içerirler. CMOS transistorların parazitik bileşenlerinden dolayı tasarlanan aktif endüktanslar belirli bir frekans bölgesinde endüktif davranış gösterirler. Alt frekans sınırı, GC devrelerinin sıfır frekansı ile belirlenirken; üst frekans sınırı ise öz-rezonans frekansı ile belirlenir. Aktif endüktansların pasif sarmal eşdeğer yapılarına göre en önemli üstünlüklerinden biri de; endüktanslarının geniş bir değer aralığıunda ayarlanabilir olmasıdır. GC aktif endüktansların endüktans değeri, transistorların geçiş-iletkenliklerinin ya da MOS varaktörlerle gerçeklenen yük kapasitanslarının değiştirilmesi ile ayarlanabilir. Literatürde, GC topolojisine dayalı pek çok CMOS AI (active inductor) devresi bildirilmiştir. Bunların tümü, farklı teknikler kullanılarak yüksek başarımlı AI yapıları oluşturmayı amaçlamışlardır. Bu tezde, bunlardan güncel olan bazı GAI (grounded AI) ve FAI (floating AI) yapıları gözden geçirilmiştir. Bunlardan bazıları, değer katsayısını (QF) iyileştirmek amacıyla, AI kaybını telafi etmek için negatif direnç kullanmışlardır. GC yapıları RF uygulamaları için tasarlandıklarında en az sayıda transistor kullanımı çok kritiktir. Çünkü bu durum AI öz-rezonans frekansının artmasına yardımcı olur. AI’ler, kazanç artırma amacıyla LNA’lerde geniş kullanım alanı bulabilmektedirler. Diğer taraftan, AI yapılarının en önemli dezvantajlarından biri gürültü başarımının pasif endüktanslara nispeten yüksek olmasıdır. Literatürde bu dezavantajı gidermek amacıyla teklif edilen yaklaşımlardan biri dejenerasyon direncinin bulunduğu bir geribesleme katı kullanılarak girişe gelen gürültü katkısını azaltmayı amaçlamıştır. Literatürde teklif edilen tekniklerin amacı, parazitik bileşenlerin etkisini azaltmak ya da tümüyle ortadan kaldırmaktır. Bu tezde, ileri devre teknikleri kullanılarak, yeni topraklı (grounded) ve yüzen (floting) AI yapıları tasarlanmıştır. AI giriş ve çıkış düğümlerine ait iletkenlikleri azaltmak için çoklu-düzenlenmiş kaskod (multi-regulated cascode, MRC) katları QF değerini iyileştirme amacıyla kullanılmaktadır. MRC katı PMOS transistorlarıyla oluşturulmuştur. PMOS transistor kullanımı, • ikinci kat kutuplamasını ayarlayabilmek amacıyla, giriş transistor boyutunun mümkün olduğunca azaltılmasını, • ana AC işaret yolundaki transistor sayısının azaltılmasını, sağlamaktadır. Tezde sunulan teorik analiz ve serim sonrası benzetim sonuçları, MRC katı kullanımının AI özelliklerine yaptığı etkiyi göstermektedir. Elde edilen sonuçlar bu katların AI tasarımında yüksek QF elde edilmesini imkan tanıdığını ortaya koynaktadır. Literatürde, iki ana AI başarım karakteristiği olan SRF ve QF başarımlarının iyileştirmesi için çok sayıda çalışma bulunmaktadır. Bu tezde, birbirlerini etkilemeksizin SRF ve QF başarımlarının ayarlanabilmesi özelliğine sahip bir AI’ın tasarımı ve benzetgimi yapılmıştır. Kaskod ve RC geribesleme yapıları yeni AI tasarımında kullanılmıştır. Daha önce de tartışıldığı üzere, AI karakterizasyonu açısından giriş transistoru çok önemlidir. Girişi transistorunun kaskodlanması, ilk jiratörün geçiş-iletkenliğinin ve giriş parazitik kapasitansının birbirinden bağımsız olarak ayarlanması gibi önemli ve kullanışlı bir özelliği beraberinde getirir. Bunun yanısıra, endüktansın değeri diğer transistorun iletkenliği ile ayarlanabilir. AI parazitik seri-rezistansını yok etmek amacıyla kullanılan RC geribeslemesi, QF iyileştirmesini sağlayabilmektedir. Kaskod transistorların kutuplama koşulu bir diyot-bağlı transistor ile sağlandığından; önerilen yapı proses, gerilim ve sıcaklık değişimleri açısından kararlı ve yüksek başarımlıdır. AI yapılarında karşılaşılan düşük gürültü başarımı, AI’ların LNA gibi RF uygulamalarda kullanımını sınırlamaktadır. Bir AI’ın ana gürültü kaynağı giriş transistorudur. Düşük gürültülü AI elde etmek için, giriş transistoru yeterince büyük boyutlu olarak tasarlanmalıdır. Ne var ki, büyük boyutlu böyle bir transistor, düşük bir SRF ve dolayısıyla sınırlı bir endüktif bandı beraberinde getirir. Bu tezde, düşük gürültülü ve az kayıplı uygun bir AI, düşük gürültü gerektiren RF uygulamaları için sunulmuştur. Teklif edilen AI devresindeki tüm transistorların ortak-kaynak (common-source, CS) yapısında kullanılması, düşük iletkenliğe sahip düğümlerin dolayısıyla yüksek QF değerine sahip bir AI’ın elde edilmesine olanak sağlamaktadır. AI gürültüsünü azaltmak için, sırasıyla P-tipi MOS transistorlar ve ileri-besleme yolu yapısı (feed-forward path, FFP) kullanılmaktadır. Bilindiği gibi, sensörler çok çeşitli fiziksel büyüklüklerin eletrik mühendisiliği alanına taşınmasını sağlamaktadır. Çok geniş kullanım alanı bulan sensör tiplerinden biri kapasitif mikro algılıyıcılardır. Kapasitif mikro algılayıcılar mekanik hareketleri küçük kapasitans değişimlerine çevirirler. Micro algılayıcıdaki kapasitans değişimi femto-Farad mertebesinde olup algılamayı zorlaştırmaktadır. Diğer yandan, küçük bir kapasitans değişimini yüksek bir empedans değişimine çevirebilmeleri dolayısıyla, GC topolojilerinin kapasitif algılayıcılarda kullanılabileceğini söylemek mümkündür. Bu tezde, bu düşünceden yola çıkılarak, kesit duyarlılığını yok etme yeteneğine sahip yeni bir 3-eksen ivme-ölçer tasarlanmıştır. Yapının, her eksendeki ivmeyi bağımsız olarak algılayabilmesi için, algılayıcı elektrodları uygun olarak yerleştirilmiştir. Daha sonra, bir kapasitif algılayıcıdaki çok küçük kapasitans değişimlerini algılayabilmek için yeni bir GC yapısı teklif edilmiştir. Önerilen yapıda, çalışma frekansı aralığı ve ölçekleme çarpanı, kutuplama akımlarının ayarlanması suretiyle birbirini etkilemeksizin ayarlanabilmektedir. Ayrıca, önerilen yapıda, parazitik bileşenlerin etkisini yok etmek için RC geribesleme ve kaskod yapılar kullanılmaktadır. Son olarak, bu tezde sunulan AI’ların çok amaçlı özellikte olduğunu göstermek amacıyla, 3 ve 6. dereceden geniş bantlı mikrodalga filtrelerde kullanılmaları ele alınmıştır. İlki 3. dereceden bir Chebyshev alçak geçiren filtredir. Basitleştirilmiş gerçel frekans tekniği (SRFT, simplified real frequency technique) ile tasarlanan ikincisi ise, 6. dereceden bir Chebyshev band geçiren filtredir. Filtrelerin benzetimle elde edilmiş frekans yanıtları, bu tezde sunulan AI’ların literatürdeki yapılara güçlü birer alternatif olduklarını ortaya koymaktadır.There is critical need for inductive characteristics in RF applications, especially in filters, LNA, VCO, bandwidth-enhancement in many kinds of amplifiers, phase shifters, power divider and matching networks. The drawbacks of using passive and spiral inductors in CMOS process are discussed in the literature. It is shown that these kind of inductors suffer from a low quality factor, a low self-resonant frequency, a low and fixed inductance value and the need for a large silicon area. Furthermore, it is shown in the literature that CMOS Active Inductors (AIs), which are synthesized using MOS transistors, offer a number of attractive characteristics as compared with their spiral counterparts. These characteristics include a low silicon consumption, a large and tunable self-resonant frequency, a large and tunable inductance, a large and tunable quality factor, and fully realizable in digital CMOS technologies. Then principles, topologies, characterizations and implementation of the Gyrator-C (GC) network is discussed in-depth. The GC networks, which are implemented by operational transconductance amplifier, are suitable for RF application. This property arises from their minimum usage of active elements. It is shown that both grounded and floating active inductors can be implemented by GC networks. To provide a quantitative measure of the performance of AIs, a number of figure-of-merits have been introduced in the thesis. These figure-of-merits include frequency range, inductance tunability, quality factor, noise and power consumption. Due to parasitic components of CMOS transistors, designed AIs have inductive behavior in a specified frequency range. The low frequency bound is set by the frequency of the zero of the gyrator-C networks while the upper frequency bound is set by Self-Resonance Frequency (SRF). One of the key advantages of active inductors over their spiral counterparts is the large tunability of their inductance. The inductance of GC AIs can be tuned by varying either the transconductances of the transconductors or the load capacitance, which is implemented by MOS varactor. Based on GC topology, there are many reported CMOS AI circuits in literature. All of them have tried to invent high performance AI by using different techniques. Some of recent proposed Grounded AI (GAI) and Floating AI (FAI) circuits are reviewed in the thesis. Some of them use negative resistor to compensate the loss of AI for QF enhancement. Some others try to use minimum number of transistors in order to increase the self-resonance frequency of AI for RF applications. In some applications, AIs are used in LNA circuits for gain boosting purpose. In that applications, designers have tried to cancel the noise of AI by using a feedback stage with a degeneration resistor to reduce the noise contribution to the input. The main aim of all the techniques is to cancel or reduce the effects of parasitic components. In the thesis, four new grounded and floating AIs are designed by using advanced circuit techniques. The first one, Multi Regulated Cascode (MRC) stages are employed for lowering conductance in input and output nodes of AI. Thus, Q performance is improved. Since these stages are used only for increasing impedance of input/output nodes, they are made up of PMOS transistors in order to: • minimize the input transistor as small as possible in order to adjust second stage biasing, • decrease the number of transistors in main path of AC signal Theoretical analysis and post-layout simulation results shows the effectiveness of using MRC stages usage in properties of AI. High Q symmetric floating version of low loss inductor is also designed by utilizing MRC stages. Designers do their best to improve SRF and QF, two main characteristics in term of AI performance. An AI with ability to adjust its SRF and QF without affecting each other is designed and simulated as a third. The cascoding and RC feedback structures are used in the new design of AI. As it discussed before, input transistor is very important regarding to AI characterizations. Cascoding input transistor gives the ability to adjust the first gyrator’s transconductance and input parasitic capacitance independently which it results in adjusting the self-resonance frequency and quality factor separately. Due to our best knowledge from literature reviewing, it is first time that the properties of an inductor can be adjusted independently. Furthermore, the inductance value can be adjusted by other transistor’s transconductances. Also, the RC feedback is utilized to cancel the parasitic series-resistance of AI which results in QF enhancement. Since, bias condition of cascoding transistors is provided by a diode-connected transistor, the proposed structure is robust in terms of performance over variation in process, voltage and temperature. The Noise of designed AIs has limited the use of them in RF applications such as LNAs. The main noise source of an AI is its input transistor. In order to have low noise AI, the input transistor should be designed large enough. But it leads to low SRF which limited the inductive frequency band. As a fourth active inductor design, a low-noise and low-loss AI is presented suitable for RF low noise applications. Utilizing all transistors in Common Sourse (CS) configuration on the AI circuit leads to low conductance nodes which causes the AI to have high Q. P-type MOS transistors and Feed-Forward Path (FFP) are employed to decrease noise of the AI, respectively. The GC topologies can convert a low capacitance variation to high impedance changing which makes it a good choice for capacitive sensors. The capacitive based micro sensors convert mechanical signals to small capacitance variation. The capacitance variation in micro sensor is in the range of femto-Farads which makes it difficult to sense. Thus, the GC topologies can be used in capacitive sensors in order to sense small capacitive variations. In the thesis, this technique is used in a new accelerometer sensor. It is first time that a gyrator-C network is employed as an interface circuit for capacitive change detection in micro sensors. The new accelerometer structure is designed by using with ability to cancel cross section sensitivity. The sensor’s electrodes are located in such a way that enables the structure to detect acceleration in 3-axis independently. Embedding all 3-axis detecting electrodes in a single proof mass and ability to detect acceleration orientation are salient features of the proposed sensor. Consequently, a new GC configuration for sensing very small capacitance changes in a capacitive sensor is presented in the thesis. In the proposed configuration, the operating frequency range and scaling factor can be adjusted without affecting each other by tuning the bias currents of utilized gyrators. In addition, the proposed configuration employs RC feedback together with the cascoding technique to cancel the effect of the parasitic components in order to get accurate scaling from gyrator-C network. Finally, in order to show versatility of designed AIs, they are used in designed third and sixth order broadband microwave filters. The first one is a third order Chebyshev low pass filter. The second one, which is designed by using simplified real frequency technique is a sixth order Chebyshev band pass filter. The simulated frequency response of filters prove the workability of the designed AIs.DoktoraPh
IMPLEMENTATION OF CMOS RF CIRCUITS WITH OCTAVE & MULTI-OCTAVE BANDWIDTH FOR PHASED ARRAY ANTENNAS
Ph.DDOCTOR OF PHILOSOPH
Monolithic active resonator filters for high frequencies
This doctoral thesis deals with monolithic active resonators and their use in high-frequency filters. The emphasis has been put on noise and distortion properties of active resonators, as these are crucial in potential applications. Two active resonator types are considered: passive LC resonators with active negative resistance compensation, and gyrator-based active inductor resonators.
An introduction to the theory of passive resonators is given, and the basic quality factor and noise characteristics are discussed in detail. Filter structures based on parallel resonators are studied and techniques for frequency tuning briefly introduced.
Based on a three-port equivalent, different negative resistor structures suitable for integration are categorized, and their fundamental small-signal and tuning properties derived. The noise properties of the topologies are analyzed and compared. The Volterra-series method is applied in the distortion estimations for each negative resistor type. Practical examples of integrated negative resistor are given with realistic measured data.
High-Q active inductors based on integrated high-frequency gyrators are analyzed using the total loop phase shift as an essential parameter. Theoretical limitations of high-frequency performance and tuning are found. Noise and distortion properties are assessed in the same manner as with negative resistors to give grounds for direct comparisons. Practical issues of monolithic active inductor resonators are tackled and realized topologies with measured results are presented.
Active resonator filters employing either of the resonator types are discussed. Their noise and distortion performance derived from the respective resonator results is calculated. Automated tuning techniques are briefly discussed. Exemplary designs are presented with measured data. The two realized active resonator filters with negative resistance resonators operate in the 3 – 4 GHz region with 1.1% and 12% relative bandwidths, 400-MHz tuning ranges, and 19-dB and 11-dB noise figures respectively. The DC power consumption is a low 15 mW per resonator. The active inductor filter has a center frequency of 2.4 GHz with almost 1-GHz tuning range. The noise figure is a high 30 dB as estimated by the theory.
System considerations show that active filters cannot directly replace passive filters in traditional radio architectures due to their relatively poor performance, but as a new potential application, an LO signal generation system for direct-conversion transmitters with a monolithic band-pass filter is presented. Both GaAs and Si-BiCMOS realizations show the feasibility of the concept. With the comparable quality factors of 415 and 300 and approximately the same –1-dB output compression points of –20 dBm, the BiCMOS topology consumes only a fraction of DC power but still gives more than 80 dBc mirror rejection thanks to its dual-mixer topology.reviewe
Recommended from our members
Surpassing Fundamental Limits through Time Varying Electromagnetics
Surpassing the fundamental limits that govern all electromagnetic structures, such as reciprocity and the delay-bandwidth-size limit, will have a transformative impact on all applications based on electromagnetic circuits and systems. For instance, violating principles of reciprocity enables non-reciprocal components such as isolators and circulators, which find application in full-duplex wireless radios, radar, biomedical imaging, and quantum computing systems. Overcoming the delay-bandwidth-size limit enables ultra-broadband yet extremely-compact devices whose size is not fundamentally related to the wavelength at the operating frequency. The focus of this dissertation is on using time-variance as a new toolbox to overcome these fundamental limits and re-imagine circuit and system design.
Traditional non-reciprocal components are realized using ferrite materials that loose their reciprocity under the application of external magnetic bias. However, the sheer volume, cost and weight of these magnet based non-reciprocal components coupled with their inability to be fabricated in conventional semiconductor processes, have limited their application to bulky and large-scale systems. Other approaches such as active-biased and non-linearity based non-reciprocity are compatible with semiconductor processes, however, they suffer from other poor linearity and noise performance. In this dissertation, using passive transistor switch as the modulating element, we have proposed the concept of spatio-temporal conductivity modulation and have demonstrated a gamut of non-reciprocal devices ranging from gyrators to isolators and circulators. Through novel circuit topologies, for the first time, we have demonstrated on-chip circulators with multi-watt input power handling, operation at high millimeter-wave frequencies, and tailor made circulators for emerging technologies such as simultaneous-transmit-and-receive MRI and quantum computing.
Delay-bandwidth-size trade-off is another fundamental electromagnetic limit, that constrains the delay imparted by a medium or a device within a fixed footprint to be inversely proportional to the signal bandwidth. It is this limit that governs the size of any microwave passive devices to be inversely proportional to its operating frequency. As a part of this dissertation, through intelligent clocking of switched capacitor networks we overcame the delay-bandwidth-size limit, thus resulting in infinitesimal, yet broadband microwave devices. Here we proposed a new paradigm in wave propagation where the properties such as the propagation delay and characteristic impedance does not depend on the constituent elements/materials of the medium, but rather heavily rely on the user-defined modulation scheme, thereby opening huge opportunities for realizing highly-reconfigurable passives. Leveraging these concepts, we demonstrated wide range of reciprocal an non-reciprocal devices including ultra-compact delay elements, highly-reconfigurable microwave passives, ultra-wideband circulators with infinitesimal form-factors and dispersion-free chip scale floquet topological insulators. Application of these devices have also been evaluated in real-world systems through our demonstrations of wideband, full-duplex receivers leveraging switched capacitors based true-time-delay interference cancelers and floquet topological insulator based antenna interfaces for full-duplex phased-arrays and ultra-wideband beamformers.
Furthermore, to cater the growing RF and microwave needs of future, large-scale quantum computing systems, we demonstrated a low-cryogenic, wideband circulator based on time modulation of superconducting devices. This superconducting circulator is expected to operate alongside the superconducting qubits, inside a dilution refrigerator at 10mK-100mK, thus enabling a tightly integrated quantum system. We also presented the design and implementation of a cryogenic-CMOS clock driver chip that will generate the clocks required by the superconducting circulator. Finally, we also demonstrated the design and implementation of a low-noise, low power consumption, 6GHz - 8GHz cryogenic downconversion receiver at 4K for cryogenic qubit readout
Recommended from our members
Fully-Integrated Magnetic-Free Nonreciprocal Components by Breaking Lorentz Reciprocity: from Physics to Applications
Reciprocity is a fundamental physical precept that governs wave propagation in a wide variety of physical domains. The various reciprocity theorems state that the response of a system remains unchanged if the excitation source and the measuring point are interchanged within a medium, and are closely related to the concept of time reversal symmetry in physics. Lorentz reciprocity is a fundamental characteristic of linear, time-invariant electronic and photonic structures with symmetric permittivity and permeability tensors. However, breaking reciprocity enables the realization of nonreciprocal components, such as isolators and circulators, which are critical to electronic, optical and acoustic systems, as well as new functionalities and devices based on novel wave propagation modes.
Nonreciprocal components have traditionally relied on magnetic materials such as ferrites that lose reciprocity under the application of an external magnetic field through the Faraday Effect. The need for a magnetic bias limits the applicability of such approaches in small-form-factor Complementary Metal–Oxide–Semiconductor (CMOS)-compatible integrated devices. One of the main features of CMOS technology is the availability of high-speed transistor switches which can be turned ON and OFF, modulating the conductance of the medium.
In this dissertation, a novel approach to break Lorentz reciprocity is presented based on staggered commutation in Linear Periodically-Time-Varying (LPTV) circuits. We have demonstrated the world’s first CMOS passive magnetic-free nonreciprocal circulator through spatio-temporal conductivity modulation. Since conductivity in semiconductors can be modulated over a wide range (CMOS transistor ON/OFF conductance ratio at Radio Frequency (RF)/millimeter-wave frequencies is as high as 103-105), commutated LPTV networks break reciprocity within a deeply sub-wavelength form-factor with low loss and high linearity.
The resulting nonreciprocal components find application in antenna interfaces of wireless communication systems, connecting the Transmitter (TX) and the Receiver (RX) to a shared antenna. This is particularly important for full-duplex wireless, where the TX and the RX operate simultaneously at the same frequency band and need to be highly isolated in order to maintain receiver sensitivity. Multiple fully-integrated full-duplex receivers are demonstrated in this dissertation that best show the synergy between the physical concept and application-based implementations by using circuit techniques to benefit the system-level performance, such as TX-side linearity enhancement and co-design and co-optimization of the antenna interface and the RX and utilization of the multi-phase structure of our antenna interfaces for analog beamforming in multi-antenna systems.
Finally, this dissertation discusses some of the fundamental limits of space-time modulated nonreciprocal structures, as well as new directions to build nonreciprocal components which can ideally be infinitesimal in size. A novel family of inductor-less nonreciprocal components including circulators and isolators have been demonstrated that achieve a wide tuning range in an infinitesimal form-factor. This family of devices combine reciprocal and nonreciprocal modes of operation, through the transfer properties of fundamental and harmonics of the system and enable a wide variety of functionalities
Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies
The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection
A Monolithic Gm-C Filter based Very Low Power, Programmable, and Multi-Channel Harmonic Discrimination System using Analog Signal Processing
A highly selective monolithic band-pass filter with programmable characteristics at micro-power operation is presented. Very low power signal processing is of great interest in wireless sensing and Internet-of-Things applications. This filter enables long-term battery powered operation of a highly selective harmonic signal discriminator for an analog signal processing system. The Gm-C biquadratic circuits were fabricated in a 0.18-μm [micrometer] CMOS process. Each 2nd-order biquad filter nominally consumes 20 μW [microwatt] and can be programmed for the desired gain (0db3dB), quality factor (5 to 20), and center-frequency from 1kHz to 100kHz. The 8th-order filter channel achieved an effective quality factor of 30 at 100kHz with an overall power consumption of 108 μW
- …