Investigation of Broadband S-Band to L-Band Erbium-Doped Fiber Amplifier (EDFA) Module

This chapter presents three sections that describe the broadband S-band to L-band erbium-doped fiber amplifier modules. In the first section, an S-band gain-clamped erbium-doped fiber amplifier (EDFA) module, employing a fiber Bragg grating (FBG) to act as a reflected element for generating a saturated tone injected into the EDFA module by using forward optical feedback method, is proposed. Moreover, the output performance of the gain and noise figure (NF) in the proposed gain-clamped S-band EDFA has been discussed in the wavelength range of 1478–1520 nm. In the second section, we demonstrate experimentally a gain-flattened two-stage erbium-based fiber amplifier (EBFA) module, which is composed of by an erbium-doped waveguide amplifier (EDWA) and a C-band EDFA in serial structure. In an operation range of 1528–1562 nm, the entire gain is larger than 35 dB and the observed NF is between 5.5 and 6.7 dB. Moreover, ±1.1 dB maximum gain variation is also obtained for the input signal power of -25 dBm. Hence, the proposed fiber amplifier not only enhances the gain but also achieves the flatness in the wavelength region. In the final section, a broadband hybrid two-stage fiber amplifier, which is composed by a C-band EDFA and a C-band semiconductor optical amplifier (SOA) in serial scheme, is investigated experimentally. Here, we only use a 3 m long erbium-doped fiber (EDF) serving as a preamplifier to increase the gain and reduce the noise figure. Therefore, the proposed hybrid amplifier achieves a 110 nm effectively amplification of 1500–1610 nm (from S- to L-band). In addition, the output performance of gain and NF in the proposed fiber amplifier has also been discussed

Fiber amplifiers, directly modulated transmitters and a ring network structure for optical communications

The three technologies that are considered the key elements in building a metropolitan area optical network are studied in this thesis. They are optical amplification, high-speed low cost transmitters and ring network structures. These studies concentrate on cost reduction of these three technologies thus enabling the use of optical networks in small customer base metropolitan areas. The research on optical amplification concentrated first on the solution doping process, at present the most used method for producing erbium doped fiber. It was found that separationing the soot growth and the sintering improved the uniformity of the porous layer. This made the homogeneity of the doping concentration in the fiber core better. The effects of index profile variations that arise from the non-ideal solution doping process were also simulated. In the search for a better doping method a new nanoparticle glass-forming process, the direct nanoparticle deposition, was developed. In this process the doping is done simultaneously with glass formation. Utilizing this new process it was possible to improve the uniformity of the doping resulting in higher usable doping levels and shorter erbium doped fiber lengths in the amplifiers. There were fewer limitations in the amplifier caused by optical non-linearities and polarization mode dispersion since shorter fiber lengths were needed. The double cladding fiber, which avoids the costly coupling of the pump laser into a single mode waveguide, was also studied. This pumping scheme was found to improve the inversion uniformity in the erbium doped fiber core thereby enhancing the power conversion efficiency for the long wavelength band amplifier. In characterizing the erbium doped fiber amplifier the gain and noise figure was measured with a temporal filter setup. It was made of simple, low cost components but yielded accurate measurements since the noise originating from the amplified spontaneous emission was measured at the signal wavelength. In the study of fiber amplifier controlling schemes the input power of the fiber amplifier was successfully used to regulate the pump laser. This feed-forward control scheme provides a simple, low cost control and managment system for the erbium doped fiber amplifier in metropolitan area network applications that require flexible adding and dropping of wavelength channels. The transmitter research focused on the DFB laser due to its simplicity and low cost structure. A solid state Fabry-Perot etalon made from double polished silicon chip was used as a frequency discriminator in the chirp analyser developed for the DFB lasers. This wavelength discriminator did not require repeated calibration or active stabilisation and was controled electrically enabling automatic measurements. The silicon Fabry-Perot etalon was also used for simultaneous spectral filtering and wavelength control of the laser. The usable dispersion limited transmission length was increased when the filter was used in conjunction with the directly modulated distributed feedback laser transmitter. The combination of spatial multiplexing and dense wavelength division multiplexing in ring topology was investigated in the course of the research on the ring network as the feeder part of the metropolitan network. A new way to organize different wavelengths and fibers was developed. This ring network structure was simulated and an experimental ring network built. The results of the studies demonstrated that the same limitations effecting uni-directional ring structures also are the main limitations on the scalability of the spatial and wavelength division multiplexed ring networks based on bi-directional transmission when the node spacing is short. The developed ring network structure demonstrated major cost reductions when compared with the heavy use of wavelength division multiplexing. The node structure was also greatly simplified resulting in less need for different wavelength transmitters in each node. Furthermore the node generated only minor losses for the passing signals thus reducing the need for optical amplification.reviewe

An Efficient and Low Noise L-band Erbium-Doped Fiber Amplifier

The use of the long-wavelength-band (Lband) is attractive for both increasing the capacity of wavelength division multiplexing (WDM) systems and has been used in WDM transmission experiments at over 1 Tb/s. Recently, a gain bandwidth of about 80nm has been achieved by integrating the L-band EDFA in parallel with conventional band (Cband) EDFA [1]. Moreover, the L-band EDFAs will make it possible to construct an effective WDM systems employing dispersion-shifted fiber (DSF) without the degradation caused by four-wave-mixing (FWM) [2]. The L-band erbium-doped fiber amplifier (EDFA) is studied because it can be constructed by silica-based erbium-doped fiber (EDF) and has a low linearity for WDM signals. However, L-band EDFAs have a low power conversion efficiency (PCE) compared to a C-band

56.6 dB high gain L-band EDFA utilizing short-length highly-doped erbium rare-earth material

In this paper, we experimentally investigate the performance of an efficient high gain L-band erbium-doped fiber (EDF) amplifier structure utilizing short-length highly-doped erbium rare-earth material with a single pump source. The amplifier gain and noise figure variation for different amplifier structures have been investigated. A filter is used to reduce the self-saturation effect and suppress the C-band amplified spontaneous emission (ASE) noise. The amplifier achieves a signal gain of 56.6 dB with a low noise figure of 4.8 dB at -50 dBm input signal power using only 8 m of EDF length. The amplifier gain shows significant improvement of 6 dB with C/L band coupler and 13 dB with tunable-band pass filter compared to amplifier structure without ASE suppression

Flat-gain wide-band erbium doped fiber amplifier by combining two difference doped fibers

A new erbium-doped fibre amplifier (EDFA) is demonstrated using a combination of newly developed Erbium Zirconia co-doped fiber (Zr-EDF) and the commercial silica-based Erbium-doped fiber (Si-EDF) as the gain medium. Both fibers have a very high concentration of erbium ion. A compact amplifier operating in C-band region is firstly reported using a double-pass configuration. It is shown that average gains of the proposed Zr-EDF amplifier are obtained at approximately 18 dB with a gain variation of +-2 dB within C-band region. A flat-gain and wide band operation is achieved by configuring the amplifier in two stages comprising a 2 m long Zr-EDF and 9 m long Si-EDF optimised for C- and L-band operations, respectively, in a double-pass parallel configuration. A chirp fibre Bragg grating (CFBG) is used in both stages to ensure double propagation of the signal and thus to increase the attainable gain in both C- and L-band regions. At an input signal power of 0 dBm, a flat gain of 15 dB is achieved with a gain variation of less than 0.5 dB within a wide wavelength range from 1530 to 1605 nm. The corresponding noise figure varies from 6.2 to 10.8 dB within this wavelength regio

Advances in Optical Amplifiers

Optical amplifiers play a central role in all categories of fibre communications systems and networks. By compensating for the losses exerted by the transmission medium and the components through which the signals pass, they reduce the need for expensive and slow optical-electrical-optical conversion. The photonic gain media, which are normally based on glass- or semiconductor-based waveguides, can amplify many high speed wavelength division multiplexed channels simultaneously. Recent research has also concentrated on wavelength conversion, switching, demultiplexing in the time domain and other enhanced functions. Advances in Optical Amplifiers presents up to date results on amplifier performance, along with explanations of their relevance, from leading researchers in the field. Its chapters cover amplifiers based on rare earth doped fibres and waveguides, stimulated Raman scattering, nonlinear parametric processes and semiconductor media. Wavelength conversion and other enhanced signal processing functions are also considered in depth. This book is targeted at research, development and design engineers from teams in manufacturing industry, academia and telecommunications service operators

Design and Experimental Characterization of EDFA Based WDM Ring Networks with Free ASE Light Re-circulation and Link Control for Network Survivability

In this paper, we theoretically and experimentally investigate the performance of erbium-doped fiber amplifier (EDFA)-based WDM ring networks with free amplified spontaneous emission (ASE) light recirculation. We show that, with proper network and amplifier design, the lasing light generated by free ASE recirculation within the looped network provides an effective gain clamping technique, ensuring limited signal power excursions under WDM channels add-drop operations. Considering a ring network composed of eight fiber sections and eight EDFAs, maximum signal power overshoots below 2.5 dB have been measured under 23 24 WDM channels drop. Optical signal-to-noise ratio (OSNR) analysis and bit-error rate (BER) measurement at 10 Gb/s confirm acceptable performances and negligible penalties due to polarization effects and relative intensity noise transfer from laser light to WDM signals. We also propose and demonstrate a new link control technique which overcomes the main limiting factors of such networks, respectively, related to OSNR degradation, stability and survivability to fiber and EDFA breakages

Flat-gain wide-band erbium doped fiber amplifier by combining two difference doped fibers

A new erbium-doped fibre amplifier (EDFA) is demonstrated using a combination of newly developed Erbium Zirconia co-doped fiber (Zr-EDF) and the commercial silica-based Erbium-doped fiber (Si-EDF) as the gain medium. Both fibers have a very high concentration of erbium ion. A compact amplifier operating in C-band region is firstly reported using a double-pass configuration. It is shown that average gains of the proposed Zr-EDF amplifier are obtained at approximately 18 dB with a gain variation of ±2 dB within C-band region. A flat-gain and wide band operation is achieved by configuring the amplifier in two stages comprising a 2 m long Zr-EDF and 9 m long Si-EDF optimised for C- and L-band operations, respectively, in a double-pass parallel configuration. A chirp fibre Bragg grating (CFBG) is used in both stages to ensure double propagation of the signal and thus to increase the attainable gain in both C- and L-band regions. At an input signal power of 0 dBm, a flat gain of 15 dB is achieved with a gain variation of less than 0.5 dB within a wide wavelength range from 1530 to 1605 nm. The corresponding noise figure varies from 6.2 to 10.8 dB within this wavelength region