Programmable rate modem utilizing digital signal processing techniques

The engineering development study to follow was written to address the need for a Programmable Rate Digital Satellite Modem capable of supporting both burst and continuous transmission modes with either binary phase shift keying (BPSK) or quadrature phase shift keying (QPSK) modulation. The preferred implementation technique is an all digital one which utilizes as much digital signal processing (DSP) as possible. Here design tradeoffs in each portion of the modulator and demodulator subsystem are outlined, and viable circuit approaches which are easily repeatable, have low implementation losses and have low production costs are identified. The research involved for this study was divided into nine technical papers, each addressing a significant region of concern in a variable rate modem design. Trivial portions and basic support logic designs surrounding the nine major modem blocks were omitted. In brief, the nine topic areas were: (1) Transmit Data Filtering; (2) Transmit Clock Generation; (3) Carrier Synthesizer; (4) Receive AGC; (5) Receive Data Filtering; (6) RF Oscillator Phase Noise; (7) Receive Carrier Selectivity; (8) Carrier Recovery; and (9) Timing Recovery

A 300-800MHz Tunable Filter and Linearized LNA applied in a Low-Noise Harmonic-Rejection RF-Sampling Receiver

A multiband flexible RF-sampling receiver aimed at software-defined radio is presented. The wideband RF sampling function is enabled by a recently proposed discrete-time mixing downconverter. This work exploits a voltage-sensing LNA preceded by a tunable LC pre-filter with one external coil to demonstrate an RF-sampling receiver with low noise figure (NF) and high harmonic rejection (HR). The second-order LC filter provides voltage pre-gain and attenuates the source noise aliasing, and it also improves the HR ratio of the sampling downconverter. The LNA consists of a simple amplifier topology built from inverters and resistors to improve the third-order nonlinearity via an enhanced voltage mirror technique. The RF-sampling receiver employs 8 times oversampling covering 300 to 800 MHz in two RF sub-bands. The chip is realized in 65 nm CMOS and the measured gain across the band is between 22 and 28 dB, while achieving a NF between 0.8 to 4.3 dB. The IIP2 varies between +38 and +49 dBm and the IIP3 between -14 dBm and -9 dBm, and the third and fifth order HR ratios are more than 60 dB. The LNA and downconverter consumes 6 mW, and the clock generator takes 12 mW at 800 MHz RF.\ud \u

An in-band full-duplex radio receiver with a passive vector modulator downmixer for self-interference cancellation

In-band full-duplex (FD) wireless, i.e., simultaneous transmission and reception at the same frequency, introduces strong self-interference (SI) that masks the signal to be received. This paper proposes a receiver in which a copy of the transmit signal is fed through a switched-resistor vector modulator (VM)that provides simultaneous downmixing, phase shift, and amplitude scaling and subtracts it in the analog baseband for up to 27 dB SI-cancellation. Cancelling before active baseband amplification avoids self-blocking, and highly linear mixers keep SIinduced distortion low, for a receiver SI-to-noise-and-distortionratio (SINDR) of up to 71.5 dB in 16.25 MHz BW. When combined with a two-port antenna with only 20 dB isolation, the low RX distortion theoretically allows sufficient digital cancellation for over 90 dB link budget, sufficient for short-range, low-power FD links

Filter Bank Multicarrier Modulation for Spectrally Agile Waveform Design

In recent years the demand for spectrum has been steadily growing. With the limited amount of spectrum available, Spectrum Pooling has gained immense popularity. As a result of various studies, it has been established that most of the licensed spectrum remains underutilized. Spectrum Pooling or spectrum sharing concentrates on making the most of these whitespaces in the licensed spectrum. These unused parts of the spectrum are usually available in chunks. A secondary user looking to utilize these chunks needs a device capable of transmitting over distributed frequencies, while not interfering with the primary user. Such a process is known as Dynamic Spectrum Access (DSA) and a device capable of it is known as Cognitive Radio. In such a scenario, multicarrier communication that transmits data across the channel in several frequency subcarriers at a lower data rate has gained prominence. Its appeal lies in the fact that it combats frequency selective fading. Two methods for implementing multicarrier modulation are non-contiguous orthogonal frequency division multiplexing (NCOFDM)and filter bank multicarrier modulation (FBMC). This thesis aims to implement a novel FBMC transmitter using software defined radio (SDR) with modulated filters based on a lowpass prototype. FBMCs employ two sets of bandpass filters called analysis and synthesis filters, one at the transmitter and the other at the receiver, in order to filter the collection of subcarriers being transmitted simultaneously in parallel frequencies. The novel aspect of this research is that a wireless transmitter based on non-contiguous FBMC is being used to design spectrally agile waveforms for dynamic spectrum access as opposed to the more popular NC-OFDM. Better spectral containment and bandwidth efficiency, combined with lack of cyclic prefix processing, makes it a viable alternative for NC-OFDM. The main aim of this thesis is to prove that FBMC can be practically implemented for wireless communications. The practicality of the method is tested by transmitting the FBMC signals real time by using the Simulink environment and USRP2 hardware modules

Hardware Implementation of Filtering Based Sidelobe Suppression for Spectrally Agile Multicarrier based Cognitive Radio Systems

Due to the ever increasing dependency on existing wireless technologies and the growing usage of sophisticated wireless devices, the demand for bandwidth is rising exponentially. Also, the Federal Communications Commission (FCC) has reserved a considerable amount of spectrum for licensed users. As a result, the unlicensed spectrum usage is constrained to the overcrowded unlicensed spectrum. Various spectral management surveys have indicated inefficient spectrum utilization in the licensed spectral bands. The congested unlicensed spectrum and inefficiently used licensed frequency bands calls for an approach to use the available spectrum opportunistically. Therefore, the concept of Spectrum Pooling , which is based on Dynamic Spectrum Access (DSA), was proposed to make the unused sections of licensed spectrum available to the unlicensed users. In Spectrum Pooling, an empty section of licensed spectrum is borrowed by a secondary user for certain period of time without interfering with the licensed user. Orthogonal Frequency Division Multiplexing (OFDM) is a transmission scheme that is a candidate for Spectrum Pooling since it is capable of forming an adaptive spectral shape that allows coexistence of licensed and unlicensed users while attemting to minimize any interference. Subcarriers in the OFDM signal can be deactivated to generate Non-Contiguous OFDM (NC-OFDM). Even though NC-OFDM allows efficient use of available spectrum, it causes out of band (OOB) radiation, which adversely affects the performance of adjacent user. This thesis presents two novel techniques for combat the effects of OOB radiation generated by NC-OFDM. The proposed techniques employ a filtering-based approach combined with the technique of windowing in order to suppress the unwanted sidelobes by around 35dB-40dB. The attenuation is achieved without affecting other transmission parameters of the secondary user significantly

Design and Implementation of a Loss-Programmable Filtering Attenuator

With the increased demand for modern wireless systems in various applications, the need for adaptable radio frequency (RF) systems has greatly increased. These modern systems rely on the ability to operate in the microwave frequency spectrum (1 GHz to 1 THz) without interference from other devices while also retaining the ability to detect very low and very high power signals simultaneously. There is also an ever-increasing demand for the reduction of cost, size, weight, and power (C-SWaP) of these modern RF systems that drives an ever-increasing demand for more agile filters in the microwave frequency spectrum. A filtering attenuator (filtenuator) is a device that combines the frequency-selective characteristics of a filter and the loss-programmable characteristics of an attenuator into a single component. In this thesis, a generalized theory of filtenuators is presented. A loss-programmable, third-order filtenuator is also designed to verify the generalized theory. The design of the filtenuator is based on tuning the resistance of a pi-network of resistors. The tuning of the resistances is achieved through the use of PIN diodes. The pi-network of resistances is built around a third-order filter that provides the filter response of the filtenuator. The filtenuator is designed to operate at 1 GHz and have a tunable attenuation range of 2-10 dB. This filtenuator demonstrates the feasibility of a tunable, low C-SWaP solution to increase RF system dynamic range as well as demonstrating a design process that allows for future development of filtenuators

A baseband wireless spectrum hypervisor for multiplexing concurrent OFDM signals

The next generation of wireless and mobile networks will have to handle a significant increase in traffic load compared to the current ones. This situation calls for novel ways to increase the spectral efficiency. Therefore, in this paper, we propose a wireless spectrum hypervisor architecture that abstracts a radio frequency (RF) front-end into a configurable number of virtual RF front ends. The proposed architecture has the ability to enable flexible spectrum access in existing wireless and mobile networks, which is a challenging task due to the limited spectrum programmability, i.e., the capability a system has to change the spectral properties of a given signal to fit an arbitrary frequency allocation. The proposed architecture is a non-intrusive and highly optimized wireless hypervisor that multiplexes the signals of several different and concurrent multi-carrier-based radio access technologies with numerologies that are multiple integers of one another, which are also referred in our work as radio access technologies with correlated numerology. For example, the proposed architecture can multiplex the signals of several Wi-Fi access points, several LTE base stations, several WiMAX base stations, etc. As it able to multiplex the signals of radio access technologies with correlated numerology, it can, for instance, multiplex the signals of LTE, 5G-NR and NB-IoT base stations. It abstracts a radio frequency front-end into a configurable number of virtual RF front ends, making it possible for such different technologies to share the same RF front-end and consequently reduce the costs and increasing the spectral efficiency by employing densification, once several networks share the same infrastructure or by dynamically accessing free chunks of spectrum. Therefore, the main goal of the proposed approach is to improve spectral efficiency by efficiently using vacant gaps in congested spectrum bandwidths or adopting network densification through infrastructure sharing. We demonstrate mathematically how our proposed approach works and present several simulation results proving its functionality and efficiency. Additionally, we designed and implemented an open-source and free proof of concept prototype of the proposed architecture, which can be used by researchers and developers to run experiments or extend the concept to other applications. We present several experimental results used to validate the proposed prototype. We demonstrate that the prototype can easily handle up to 12 concurrent physical layers