OFDM Waveform Optimisation for Joint Communications and Sensing

Radar systems are radios to sense objects in their surrounding environment. These operate at a defined set of frequency ranges. Communication systems are used to transfer information between two points. In the present day, proliferation of mobile devices and the advancement of technology have led to communication systems being ubiquitous. This has made these systems to operate at the frequency bands already used by the radar systems. Thus, the communication signal interferes a radar receiver and vice versa, degrading performance of both systems. Different methods have been proposed to combat this phenomenon. One of the novel topics in this is the RF convergence, where a given bandwidth is used jointly by both systems. A differentiation criterion must be adopted between the two systems so that a receiver is able to separately extract radar and communication signals. The hardware convergence due to the emergence of software-defined radios also motivated a single system be used for both radar and communication. A joint waveform is adopted for both radar and communication systems, as the transmit signal. As orthogonal frequency-division multiplexing (OFDM) waveform is the most prominent in mobile communications, it is selected as the joint waveform. Considering practical cellular communication systems adopting OFDM, there often exist unused subcarriers within OFDM symbols. These can be filled up with arbitrary data to improve the performance of the radar system. This is the approach used, where the filling up is performed through an optimisation algorithm. The filled subcarriers are termed as radar subcarriers while the rest as communication subcarriers, throughout the thesis. The optimisation problem minimises the Cramer--Rao lower bounds of the delay and Doppler estimates made by the radar system subject to a set of constraints. It also outputs the indices of the radar and communication subcarriers within an OFDM symbol, which minimise the lower bounds. The first constraint allocates power between radar and communication subcarriers depending on their subcarrier ratio in an OFDM symbol. The second constraint ensures the peak-to-average power ratio (PAPR) of the joint waveform has an acceptable level of PAPR. The results show that the optimised waveform provides significant improvement in the Cramer--Rao lower bounds compared with the unoptimised waveform. In compensation for this, the power allocated to the communication subcarriers needs to be reduced. Thus, improving the performances of the radar and communication systems are a trade-off. It is also observed that for the minimum lower bounds, radar subcarriers need to be placed at the two edges of an OFDM symbol. Optimisation is also seen to improve the estimation performance of a maximum likelihood estimator, concluding that optimising the subcarriers to minimise a theoretical bound enables to achieve improvement for practical systems

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium