Efficient FPGA implementations of volterra DFES for optical systems

In this work suitable architectures and high-throughput FPGA implementations of Volterra Decision Feedback Equalizers (VDFEs) for optical communication links are presented. Two VDFE configurations were selected based on the available resources of the employed FPGA devices, and two multiplexer-based architectures were developed for each of them in order to achieve the target throughput. The comparison of the experimental results with respect to different VDFE configurations, throughput, and FPGA devices points out the platform-specific design characteristics. The introduced architectures meet the desired 10Gb/s throughput, so it is demonstrated that the FPGA is a suitable platform for high-speed optical fiber communication systems

FPGA implementation of a MIMO DFE in 40 GB/S DQPSK optical links

In this paper, an FPGA implementation of a Multi Input Multi Output (MIMO) Decision Feedback equalizer (DFE) is proposed, for the electronic compensation of the impairments in 40Gb/s Intensity Modulated Direct Detection (IM/DD) optical communication links employing NRZ DQPSK signaling. The proposed equalizer is used for the electronic compensation the residual Chromatic Dispersion (CD) along the installed optically compensated optical paths. The required processing rate is achieved by applying intensive pipelining and parallelism in the original architecture of the equalizer. At the given processing rate, a 8-input 2-output DFE involving three taps feedforward filtering and two taps backward filtering is implemented on a single, cutting edge technology, Xilinx FPGA device

Machine learning for optical fiber communication systems: An introduction and overview

Optical networks generate a vast amount of diagnostic, control and performance monitoring data. When information is extracted from this data, reconfigurable network elements and reconfigurable transceivers allow the network to adapt both to changes in the physical infrastructure but also changing traffic conditions. Machine learning is emerging as a disruptive technology for extracting useful information from this raw data to enable enhanced planning, monitoring and dynamic control. We provide a survey of the recent literature and highlight numerous promising avenues for machine learning applied to optical networks, including explainable machine learning, digital twins and approaches in which we embed our knowledge into the machine learning such as physics-informed machine learning for the physical layer and graph-based machine learning for the networking layer

ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Energy-Efficient Receiver Design for High-Speed Interconnects

High-speed interconnects are of vital importance to the operation of high-performance computing and communication systems, determining the ultimate bandwidth or data rates at which the information can be exchanged. Optical interconnects and the employment of high-order modulation formats are considered as the solutions to fulfilling the envisioned speed and power efficiency of future interconnects. One common key factor in bringing the success is the availability of energy-efficient receivers with superior sensitivity. To enhance the receiver sensitivity, improvement in the signal-to-noise ratio (SNR) of the front-end circuits, or equalization that mitigates the detrimental inter-symbol interference (ISI) is required. In this dissertation, architectural and circuit-level energy-efficient techniques serving these goals are presented. First, an avalanche photodetector (APD)-based optical receiver is described, which utilizes non-return-to-zero (NRZ) modulation and is applicable to burst-mode operation. For the purposes of improving the overall optical link energy efficiency as well as the link bandwidth, this optical receiver is designed to achieve high sensitivity and high reconfiguration speed. The high sensitivity is enabled by optimizing the SNR at the front-end through adjusting the APD responsivity via its reverse bias voltage, along with the incorporation of 2-tap feedforward equalization (FFE) and 2-tap decision feedback equalization (DFE) implemented in current-integrating fashion. The high reconfiguration speed is empowered by the proposed integrating dc and amplitude comparators, which eliminate the RC settling time constraints. The receiver circuits, excluding the APD die, are fabricated in 28-nm CMOS technology. The optical receiver achieves bit-error-rate (BER) better than 1E−12 at −16-dBm optical modulation amplitude (OMA), 2.24-ns reconfiguration time with 5-dB dynamic range, and 1.37-pJ/b energy efficiency at 25 Gb/s. Second, a 4-level pulse amplitude modulation (PAM4) wireline receiver is described, which incorporates continuous time linear equalizers (CTLEs) and a 2-tap direct DFE dedicated to the compensation for the first and second post-cursor ISI. The direct DFE in a PAM4 receiver (PAM4-DFE) is made possible by the proposed CMOS track-and-regenerate slicer. This proposed slicer offers rail-to-rail digital feedback signals with significantly improved clock-to-Q delay performance. The reduced slicer delay relaxes the settling time constraint of the summer circuits and allows the stringent DFE timing constraint to be satisfied. With the availability of a direct DFE employing the proposed slicer, inductor-based bandwidth enhancement and loop-unrolling techniques, which can be power/area intensive, are not required. Fabricated in 28-nm CMOS technology, the PAM4 receiver achieves BER better than 1E−12 and 1.1-pJ/b energy efficiency at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist frequency. Third, digital neural-network-enhanced FFEs (NN-FFEs) for PAM4 analog-to-digital converter (ADC)-based optical interconnects are described. The proposed NN-FFEs employ a custom learnable piecewise linear (PWL) activation function to tackle the nonlinearities with short memory lengths. In contrast to the conventional Volterra equalizers where multipliers are utilized to generate the nonlinear terms, the proposed NN-FFEs leverage the custom PWL activation function for nonlinear operations and reduce the required number of multipliers, thereby improving the area and power efficiencies. Applications in the optical interconnects based on micro-ring modulators (MRMs) are demonstrated with simulation results of 50-Gb/s and 100-Gb/s links adopting PAM4 signaling. The proposed NN-FFEs and the conventional Volterra equalizers are synthesized with the standard-cell libraries in a commercial 28-nm CMOS technology, and their power consumptions and performance are compared. Better than 37% lower power overhead can be achieved by employing the proposed NN-FFEs, in comparison with the Volterra equalizer that leads to similar improvement in the symbol-error-rate (SER) performance.</p