New Design Techniques for Dynamic Reconfigurable Architectures

L'abstract è presente nell'allegato / the abstract is in the attachmen

DeSyRe: on-Demand System Reliability

The DeSyRe project builds on-demand adaptive and reliable Systems-on-Chips (SoCs). As fabrication technology scales down, chips are becoming less reliable, thereby incurring increased power and performance costs for fault tolerance. To make matters worse, power density is becoming a significant limiting factor in SoC design, in general. In the face of such changes in the technological landscape, current solutions for fault tolerance are expected to introduce excessive overheads in future systems. Moreover, attempting to design and manufacture a totally defect and fault-free system, would impact heavily, even prohibitively, the design, manufacturing, and testing costs, as well as the system performance and power consumption. In this context, DeSyRe delivers a new generation of systems that are reliable by design at well-balanced power, performance, and design costs. In our attempt to reduce the overheads of fault-tolerance, only a small fraction of the chip is built to be fault-free. This fault-free part is then employed to manage the remaining fault-prone resources of the SoC. The DeSyRe framework is applied to two medical systems with high safety requirements (measured using the IEC 61508 functional safety standard) and tight power and performance constraints

Improving reconfigurable systems reliability by combining periodical test and redundancy techniques: a case study

This paper revises and introduces to the field of reconfigurable computer systems, some traditional techniques used in the fields of fault-tolerance and testing of digital circuits. The target area is that of on-board spacecraft electronics, as this class of application is a good candidate for the use of reconfigurable computing technology. Fault tolerant strategies are used in order for the system to adapt itself to the severe conditions found in space. In addition, the paper describes some problems and possible solutions for the use of reconfigurable components, based on programmable logic, in space applications

Dynamic Partial Reconfiguration for Dependable Systems

Moore’s law has served as goal and motivation for consumer electronics manufacturers in the last decades. The results in terms of processing power increase in the consumer electronics devices have been mainly achieved due to cost reduction and technology shrinking. However, reducing physical geometries mainly affects the electronic devices’ dependability, making them more sensitive to soft-errors like Single Event Transient (SET) of Single Event Upset (SEU) and hard (permanent) faults, e.g. due to aging effects. Accordingly, safety critical systems often rely on the adoption of old technology nodes, even if they introduce longer design time w.r.t. consumer electronics. In fact, functional safety requirements are increasingly pushing industry in developing innovative methodologies to design high-dependable systems with the required diagnostic coverage. On the other hand commercial off-the-shelf (COTS) devices adoption began to be considered for safety-related systems due to real-time requirements, the need for the implementation of computationally hungry algorithms and lower design costs. In this field FPGA market share is constantly increased, thanks to their flexibility and low non-recurrent engineering costs, making them suitable for a set of safety critical applications with low production volumes. The works presented in this thesis tries to face new dependability issues in modern reconfigurable systems, exploiting their special features to take proper counteractions with low impacton performances, namely Dynamic Partial Reconfiguration

A DevOps approach to integration of software components in an EU research project

We present a description of the development and deployment infrastructure being created to support the integration effort of HARNESS, an EU FP7 project. HARNESS is a multi-partner research project intended to bring the power of heterogeneous resources to the cloud. It consists of a number of different services and technologies that interact with the OpenStack cloud computing platform at various levels. Many of these components are being developed independently by different teams at different locations across Europe, and keeping the work fully integrated is a challenge. We use a combination of Vagrant based virtual machines, Docker containers, and Ansible playbooks to provide a consistent and up-to-date environment to each developer. The same playbooks used to configure local virtual machines are also used to manage a static testbed with heterogeneous compute and storage devices, and to automate ephemeral larger-scale deployments to Grid5000. Access to internal projects is managed by GitLab, and automated testing of services within Docker-based environments and integrated deployments within virtual-machines is provided by Buildbot

Toward Fault-Tolerant Applications on Reconfigurable Systems-on-Chip

L'abstract è presente nell'allegato / the abstract is in the attachmen

Adaptive Intelligent Systems for Extreme Environments

As embedded processors become powerful, a growing number of embedded systems equipped with artificial intelligence (AI) algorithms have been used in radiation environments to perform routine tasks to reduce radiation risk for human workers. On the one hand, because of the low price, commercial-off-the-shelf devices and components are becoming increasingly popular to make such tasks more affordable. Meanwhile, it also presents new challenges to improve radiation tolerance, the capability to conduct multiple AI tasks and deliver the power efficiency of the embedded systems in harsh environments. There are three aspects of research work that have been completed in this thesis: 1) a fast simulation method for analysis of single event effect (SEE) in integrated circuits, 2) a self-refresh scheme to detect and correct bit-flips in random access memory (RAM), and 3) a hardware AI system with dynamic hardware accelerators and AI models for increasing flexibility and efficiency. The variances of the physical parameters in practical implementation, such as the nature of the particle, linear energy transfer and circuit characteristics, may have a large impact on the final simulation accuracy, which will significantly increase the complexity and cost in the workflow of the transistor level simulation for large-scale circuits. It makes it difficult to conduct SEE simulations for large-scale circuits. Therefore, in the first research work, a new SEE simulation scheme is proposed, to offer a fast and cost-efficient method to evaluate and compare the performance of large-scale circuits which subject to the effects of radiation particles. The advantages of transistor and hardware description language (HDL) simulations are combined here to produce accurate SEE digital error models for rapid error analysis in large-scale circuits. Under the proposed scheme, time-consuming back-end steps are skipped. The SEE analysis for large-scale circuits can be completed in just few hours. In high-radiation environments, bit-flips in RAMs can not only occur but may also be accumulated. However, the typical error mitigation methods can not handle high error rates with low hardware costs. In the second work, an adaptive scheme combined with correcting codes and refreshing techniques is proposed, to correct errors and mitigate error accumulation in extreme radiation environments. This scheme is proposed to continuously refresh the data in RAMs so that errors can not be accumulated. Furthermore, because the proposed design can share the same ports with the user module without changing the timing sequence, it thus can be easily applied to the system where the hardware modules are designed with fixed reading and writing latency. It is a challenge to implement intelligent systems with constrained hardware resources. In the third work, an adaptive hardware resource management system for multiple AI tasks in harsh environments was designed. Inspired by the “refreshing” concept in the second work, we utilise a key feature of FPGAs, partial reconfiguration, to improve the reliability and efficiency of the AI system. More importantly, this feature provides the capability to manage the hardware resources for deep learning acceleration. In the proposed design, the on-chip hardware resources are dynamically managed to improve the flexibility, performance and power efficiency of deep learning inference systems. The deep learning units provided by Xilinx are used to perform multiple AI tasks simultaneously, and the experiments show significant improvements in power efficiency for a wide range of scenarios with different workloads. To further improve the performance of the system, the concept of reconfiguration was further extended. As a result, an adaptive DL software framework was designed. This framework can provide a significant level of adaptability support for various deep learning algorithms on an FPGA-based edge computing platform. To meet the specific accuracy and latency requirements derived from the running applications and operating environments, the platform may dynamically update hardware and software (e.g., processing pipelines) to achieve better cost, power, and processing efficiency compared to the static system

Enhancing Real-time Embedded Image Processing Robustness on Reconfigurable Devices for Critical Applications

Nowadays, image processing is increasingly used in several application fields, such as biomedical, aerospace, or automotive. Within these fields, image processing is used to serve both non-critical and critical tasks. As example, in automotive, cameras are becoming key sensors in increasing car safety, driving assistance and driving comfort. They have been employed for infotainment (non-critical), as well as for some driver assistance tasks (critical), such as Forward Collision Avoidance, Intelligent Speed Control, or Pedestrian Detection. The complexity of these algorithms brings a challenge in real-time image processing systems, requiring high computing capacity, usually not available in processors for embedded systems. Hardware acceleration is therefore crucial, and devices such as Field Programmable Gate Arrays (FPGAs) best fit the growing demand of computational capabilities. These devices can assist embedded processors by significantly speeding-up computationally intensive software algorithms. Moreover, critical applications introduce strict requirements not only from the real-time constraints, but also from the device reliability and algorithm robustness points of view. Technology scaling is highlighting reliability problems related to aging phenomena, and to the increasing sensitivity of digital devices to external radiation events that can cause transient or even permanent faults. These faults can lead to wrong information processed or, in the worst case, to a dangerous system failure. In this context, the reconfigurable nature of FPGA devices can be exploited to increase the system reliability and robustness by leveraging Dynamic Partial Reconfiguration features. The research work presented in this thesis focuses on the development of techniques for implementing efficient and robust real-time embedded image processing hardware accelerators and systems for mission-critical applications. Three main challenges have been faced and will be discussed, along with proposed solutions, throughout the thesis: (i) achieving real-time performances, (ii) enhancing algorithm robustness, and (iii) increasing overall system's dependability. In order to ensure real-time performances, efficient FPGA-based hardware accelerators implementing selected image processing algorithms have been developed. Functionalities offered by the target technology, and algorithm's characteristics have been constantly taken into account while designing such accelerators, in order to efficiently tailor algorithm's operations to available hardware resources. On the other hand, the key idea for increasing image processing algorithms' robustness is to introduce self-adaptivity features at algorithm level, in order to maintain constant, or improve, the quality of results for a wide range of input conditions, that are not always fully predictable at design-time (e.g., noise level variations). This has been accomplished by measuring at run-time some characteristics of the input images, and then tuning the algorithm parameters based on such estimations. Dynamic reconfiguration features of modern reconfigurable FPGA have been extensively exploited in order to integrate run-time adaptivity into the designed hardware accelerators. Tools and methodologies have been also developed in order to increase the overall system dependability during reconfiguration processes, thus providing safe run-time adaptation mechanisms. In addition, taking into account the target technology and the environments in which the developed hardware accelerators and systems may be employed, dependability issues have been analyzed, leading to the development of a platform for quickly assessing the reliability and characterizing the behavior of hardware accelerators implemented on reconfigurable FPGAs when they are affected by such faults