Experimental Evaluation of Techniques to Lower Spectrum Consumption in Wi-Red

Seamless redundancy layered atop Wi-Fi has been shown able to tangibly increase communication quality, hence offering industry-grade reliability. However, it also implies much higher network traffic, which is often unbearable as the wireless spectrum is a shared and scarce resource. To deal with this drawback the Wi-Red proposal includes suitable duplication avoidance mechanisms, which reduce spectrum consumption by preventing transmission on air of inessential frame duplicates. In this paper, the ability of such mechanisms to save wireless bandwidth is experimentally evaluated. To this purpose, specific post-analysis techniques have been defined, which permit to carry out such an assessment on a simple testbed that relies on plain redundancy and do not require any changes to the adapters' firmware. As results show, spectrum consumption decreases noticeably without communication quality is impaired. Further saving can be obtained if a slight worsening is tolerated for latencies.Comment: preprint, 13 page

Exploiting the power of multiplicity: a holistic survey of network-layer multipath

The Internet is inherently a multipath network: For an underlying network with only a single path, connecting various nodes would have been debilitatingly fragile. Unfortunately, traditional Internet technologies have been designed around the restrictive assumption of a single working path between a source and a destination. The lack of native multipath support constrains network performance even as the underlying network is richly connected and has redundant multiple paths. Computer networks can exploit the power of multiplicity, through which a diverse collection of paths is resource pooled as a single resource, to unlock the inherent redundancy of the Internet. This opens up a new vista of opportunities, promising increased throughput (through concurrent usage of multiple paths) and increased reliability and fault tolerance (through the use of multiple paths in backup/redundant arrangements). There are many emerging trends in networking that signify that the Internet's future will be multipath, including the use of multipath technology in data center computing; the ready availability of multiple heterogeneous radio interfaces in wireless (such as Wi-Fi and cellular) in wireless devices; ubiquity of mobile devices that are multihomed with heterogeneous access networks; and the development and standardization of multipath transport protocols such as multipath TCP. The aim of this paper is to provide a comprehensive survey of the literature on network-layer multipath solutions. We will present a detailed investigation of two important design issues, namely, the control plane problem of how to compute and select the routes and the data plane problem of how to split the flow on the computed paths. The main contribution of this paper is a systematic articulation of the main design issues in network-layer multipath routing along with a broad-ranging survey of the vast literature on network-layer multipathing. We also highlight open issues and identify directions for future work

A study of the applicability of software-defined networking in industrial networks

173 p.Las redes industriales interconectan sensores y actuadores para llevar a cabo funciones de monitorización, control y protección en diferentes entornos, tales como sistemas de transporte o sistemas de automatización industrial. Estos sistemas ciberfísicos generalmente están soportados por múltiples redes de datos, ya sean cableadas o inalámbricas, a las cuales demandan nuevas prestaciones, de forma que el control y gestión de tales redes deben estar acoplados a las condiciones del propio sistema industrial. De este modo, aparecen requisitos relacionados con la flexibilidad, mantenibilidad y adaptabilidad, al mismo tiempo que las restricciones de calidad de servicio no se vean afectadas. Sin embargo, las estrategias de control de red tradicionales generalmente no se adaptan eficientemente a entornos cada vez más dinámicos y heterogéneos.Tras definir un conjunto de requerimientos de red y analizar las limitaciones de las soluciones actuales, se deduce que un control provisto independientemente de los propios dispositivos de red añadiría flexibilidad a dichas redes. Por consiguiente, la presente tesis explora la aplicabilidad de las redes definidas por software (Software-Defined Networking, SDN) en sistemas de automatización industrial. Para llevar a cabo este enfoque, se ha tomado como caso de estudio las redes de automatización basadas en el estándar IEC 61850, el cual es ampliamente usado en el diseño de las redes de comunicaciones en sistemas de distribución de energía, tales como las subestaciones eléctricas. El estándar IEC 61850 define diferentes servicios y protocolos con altos requisitos en terminos de latencia y disponibilidad de la red, los cuales han de ser satisfechos mediante técnicas de ingeniería de tráfico. Como resultado, aprovechando la flexibilidad y programabilidad ofrecidas por las redes definidas por software, en esta tesis se propone una arquitectura de control basada en el protocolo OpenFlow que, incluyendo tecnologías de gestión y monitorización de red, permite establecer políticas de tráfico acorde a su prioridad y al estado de la red.Además, las subestaciones eléctricas son un ejemplo representativo de infraestructura crítica, que son aquellas en las que un fallo puede resultar en graves pérdidas económicas, daños físicos y materiales. De esta forma, tales sistemas deben ser extremadamente seguros y robustos, por lo que es conveniente la implementación de topologías redundantes que ofrezcan un tiempo de reacción ante fallos mínimo. Con tal objetivo, el estándar IEC 62439-3 define los protocolos Parallel Redundancy Protocol (PRP) y High-availability Seamless Redundancy (HSR), los cuales garantizan un tiempo de recuperación nulo en caso de fallo mediante la redundancia activa de datos en redes Ethernet. Sin embargo, la gestión de redes basadas en PRP y HSR es estática e inflexible, lo que, añadido a la reducción de ancho de banda debida la duplicación de datos, hace difícil un control eficiente de los recursos disponibles. En dicho sentido, esta tesis propone control de la redundancia basado en el paradigma SDN para un aprovechamiento eficiente de topologías malladas, al mismo tiempo que se garantiza la disponibilidad de las aplicaciones de control y monitorización. En particular, se discute cómo el protocolo OpenFlow permite a un controlador externo configurar múltiples caminos redundantes entre dispositivos con varias interfaces de red, así como en entornos inalámbricos. De esta forma, los servicios críticos pueden protegerse en situaciones de interferencia y movilidad.La evaluación de la idoneidad de las soluciones propuestas ha sido llevada a cabo, principalmente, mediante la emulación de diferentes topologías y tipos de tráfico. Igualmente, se ha estudiado analítica y experimentalmente cómo afecta a la latencia el poder reducir el número de saltos en las comunicaciones con respecto al uso de un árbol de expansión, así como balancear la carga en una red de nivel 2. Además, se ha realizado un análisis de la mejora de la eficiencia en el uso de los recursos de red y la robustez alcanzada con la combinación de los protocolos PRP y HSR con un control llevado a cabo mediante OpenFlow. Estos resultados muestran que el modelo SDN podría mejorar significativamente las prestaciones de una red industrial de misión crítica

Design of interface selection protocols for multi-homed wireless networks

This thesis was submitted for the degree of Doctor of Philosophy and was awarded by Brunel University on 10 December 2010.The IEEE 802.11/802.16 standards conformant wireless communication stations have multi-homing transmission capability. To achieve greater communication efficiency, multi-homing capable stations use handover mechanism to select appropriate transmission channel according to variations in the channel quality. This thesis presents three internal-linked handover schemes, (1) Interface Selection Protocol (ISP), belonging to Wireless Local Area Network (WLAN)- Worldwide Interoperability for Microwave Access (WiMAX) environment (2) Fast Channel Scanning (FCS) and (3) Traffic Manager (TM), (2) and (3) belonging to WiMAX Environment. The proposed schemes in this thesis use a novel mechanism of providing a reliable communication route. This solution is based on a cross-layer communication framework, where the interface selection module uses various network related parameters from Medium Access Control (MAC) sub-layer/Physical Layer (PHY) across the protocol suite for decision making at the Network layer. The proposed solutions are highly responsive when compared with existing multi-homed schemes; responsiveness is one of the key factors in the design of such protocols. Selected route under these schemes is based on the most up to date link-layer information. Therefore, such a route is not only reliable in terms of route optimization but it also fulfils the application demands in terms of throughput and delay. Design of ISP protocol use probing frames during the route discovery process. The 802.11 mandates the use of different rates for data transmission frames. The ISP-metric can be incorporated into various routing aspects and its applicability is determined by the possibility of provision of MAC dependent parameters that are used to determine the best path metric values. In many cases, higher device density, interference and mobility cause variable medium access delays. It causes creation of ‘unreachable zones’, where destination is marked as unreachable. However, by use of the best path metric, the destination has been made reachable, anytime and anywhere, because of the intelligent use of the probing frames and interface selection algorithm implemented. The IEEE 802.16e introduces several MAC level queues for different access categories, maintaining service requirement within these queues; which imply that frames from a higher priority queue, i.e. video frames, are serviced more frequently than those belonging to lower priority queues. Such an enhancement at the MAC sub-layer introduces uneven queuing delays. Conventional routing protocols are unaware of such MAC specific constraints and as a result, these factors are not considered which result in channel performance degradation. To meet such challenges, the thesis presents FCS and TM schemes for WiMAX. For FCS, Its solution is to improve the mobile WiMAX handover and address the scanning latency. Since minimum scanning time is the most important issue in the handover process. This handover scheme aims to utilize the channel efficiently and apply such a procedure to reduce the time it takes to scan the neighboring access stations. TM uses MAC and physical layer (PHY) specific information in the interface metric and maintains a separate path to destination by applying an alternative interface operation. Simulation tests and comparisons with existing multi-homed protocols and handover schemes demonstrate the effectiveness of incorporating the medium dependent parameters. Moreover, show that suggested schemes, have shown better performance in terms of end-to-end delay and throughput, with efficiency up to 40% in specific test scenarios

Heterogeneous LTE/ Wi-Fi architecture for intelligent transportation systems

Intelligent Transportation Systems (ITS) make use of advanced technologies to enhance road safety and improve traffic efficiency. It is anticipated that ITS will play a vital future role in improving traffic efficiency, safety, comfort and emissions. In order to assist the passengers to travel safely, efficiently and conveniently, several application requirements have to be met simultaneously. In addition to the delivery of regular traffic and safety information, vehicular networks have been recently required to support infotainment services. Previous vehicular network designs and architectures do not satisfy this increasing traffic demand as they are setup for either voice or data traffic, which is not suitable for the transfer of vehicular traffic. This new requirement is one of the key drivers behind the need for new mobile wireless broadband architectures and technologies. For this purpose, this thesis proposes and investigates a heterogeneous IEEE 802.11 and LTE vehicular system that supports both infotainment and ITS traffic control data. IEEE 802.11g is used for V2V communications and as an on-board access network while, LTE is used for V2I communications. A performance simulation-based study is conducted to validate the feasibility of the proposed system in an urban vehicular environment. The system performance is evaluated in terms of data loss, data rate, delay and jitter. Several simulation scenarios are performed and evaluated. In the V2I-only scenario, the delay, jitter and data drops for both ITS and video traffic are within the acceptable limits, as defined by vehicular application requirements. Although a tendency of increase in video packet drops during handover from one eNodeB to another is observed yet, the attainable data loss rate is still below the defined benchmarks. In the integrated V2V-V2I scenario, data loss in uplink ITS traffic was initially observed so, Burst communication technique is applied to prevent packet losses in the critical uplink ITS traffic. A quantitative analysis is performed to determine the number of packets per burst, the inter-packet and inter-burst intervals. It is found that a substantial improvement is achieved using a two-packet Burst, where no packets are lost in the uplink direction. The delay, jitter and data drops for both uplink and downlink ITS traffic, and video traffic are below the benchmarks of vehicular applications. Thus, the results indicate that the proposed heterogeneous system offers acceptable performance that meets the requirements of the different vehicular applications. All simulations are conducted on OPNET Network Modeler and results are subjected to a 95% confidence analysis