Fast synchronization 3R burst-mode receivers for passive optical networks

This paper gives a tutorial overview on high speed burst-mode receiver (BM-RX) requirements, specific for time division multiplexing passive optical networks, and design issues of such BM-RXs as well as their advanced design techniques. It focuses on how to design BM-RXs with short burst overhead for fast synchronization. We present design principles and circuit architectures of various types of burst-mode transimpedance amplifiers, burst-mode limiting amplifiers and burst-mode clock and data recovery circuits. The recent development of 10 Gb/s BM-RXs is highlighted also including dual-rate operation for coexistence with deployed PONs and on-chip auto reset generation to eliminate external timing-critical control signals provided by a PON medium access control. Finally sub-system integration and state-of-the-art system performance for 10 Gb/s PONs are reviewed

Mixed-signal CNN array chips for image processing

Due to their local connectivity and wide functional capabilities, cellular nonlinear networks (CNN) are excellent candidates for the implementation of image processing algorithms using VLSI analog parallel arrays. However, the design of general purpose, programmable CNN chips with dimensions required for practical applications raises many challenging problems to analog designers. This is basically due to the fact that large silicon area means large development cost, large spatial deviations of design parameters and low production yield. CNN designers must face different issues to keep reasonable enough accuracy level and production yield together with reasonably low development cost in their design of large CNN chips. This paper outlines some of these major issues and their solutions

A RISC-V Vector Processor With Simultaneous-Switching Switched-Capacitor DC-DC Converters in 28 nm FDSOI

This work demonstrates a RISC-V vector microprocessor implemented in 28 nm FDSOI with fully integrated simultaneous-switching switched-capacitor DC-DC (SC DC-DC) converters and adaptive clocking that generates four on-chip voltages between 0.45 and 1 V using only 1.0 V core and 1.8 V IO voltage inputs. The converters achieve high efficiency at the system level by switching simultaneously to avoid charge-sharing losses and by using an adaptive clock to maximize performance for the resulting voltage ripple. Details about the implementation of the DC-DC switches, DC-DC controller, and adaptive clock are provided, and the sources of conversion loss are analyzed based on measured results. This system pushes the capabilities of dynamic voltage scaling by enabling fast transitions (20 ns), simple packaging (no off-chip passives), low area overhead (16%), high conversion efficiency (80%-86%), and high energy efficiency (26.2 DP GFLOPS/W) for mobile devices

Testing microelectronic biofluidic systems

According to the 2005 International Technology Roadmap for Semiconductors, the integration of emerging nondigital CMOS technologies will require radically different test methods, posing a major challenge for designers and test engineers. One such technology is microelectronic fluidic (MEF) arrays, which have rapidly gained importance in many biological, pharmaceutical, and industrial applications. The advantages of these systems, such as operation speed, use of very small amounts of liquid, on-board droplet detection, signal conditioning, and vast digital signal processing, make them very promising. However, testable design of these devices in a mass-production environment is still in its infancy, hampering their low-cost introduction to the market. This article describes analog and digital MEF design and testing method

Fault-tolerant design of RF front-end circuits

The continuing trends of scaling in the CMOS industry have, inevitably, been accompanied by an ever-increasing array of process faults and fabrication complexities. The relentless march towards miniaturization and massive integration, in addition to increasing operating frequencies has resulted in increasing concerns about the reliability of integrated RF front-ends. Coupled with rising cost per chip, the fault-tolerant paradigm has become pertinent in the RFIC domain. Two main reasons have contributed to the fact that fault-tolerant solutions for circuits that operate in the GHz domain have not been realized so far. First, GHz signals are extremely sensitive to higher-order effects such as stray pick-ups, interference, package & on-chip parasitics, etc. Secondly, the use of passives, especially inductors, in the feedback path poses huge area overheads, in addition to a slew of instability problems due to wide variations and soft faults. Hence traditional fault-tolerance methods used in digital and low frequency analog circuits cannot be applied in the RF domain. This work presents a unique methodology to achieve fault-tolerance in RF circuits through dynamic sensing and on-chip self-correction, along with the development of robust algorithms. This technique is minimally intrusive and is transparent during \u27normal\u27 use of the circuit. It is characterized by low area and power overheads, does not need any off-chip computing or DSP cores, and is characterized by self-correction times in the range of a few hundreds of microseconds. It compares very well with existing commercial RF test solutions that use DSP cores and require hundreds of milliseconds. The methodology is demonstrated on a LNA, since it is critical for the performance of the entire front-end. It is validated with simulation and fabrication results of the system designed in IBM 0.25 µm CMOS 6RF process

Ring oscillator clocks and margins

How much margin do we have to add to the delay lines of a bundled-data circuit? This paper is an attempt to give a methodical answer to this question, taking into account all sources of variability and the existing EDA machinery for timing analysis and sign-off. The paper is based on the study of the margins of a ring oscillator that substitutes a PLL as clock generator. A timing model is proposed that shows that a 12% margin for delay lines can be sufficient to cover variability in a 65nm technology. In a typical scenario, performance and energy improvements between 15% and 35% can be obtained by using a ring oscillator instead of a PLL. The paper concludes that a synchronous circuit with a ring oscillator clock shows similar benefits in performance and energy as those of bundled-data asynchronous circuits.Peer ReviewedPostprint (author's final draft