A Practical Cooperative Multicell MIMO-OFDMA Network Based on Rank Coordination

An important challenge of wireless networks is to boost the cell edge performance and enable multi-stream transmissions to cell edge users. Interference mitigation techniques relying on multiple antennas and coordination among cells are nowadays heavily studied in the literature. Typical strategies in OFDMA networks include coordinated scheduling, beamforming and power control. In this paper, we propose a novel and practical type of coordination for OFDMA downlink networks relying on multiple antennas at the transmitter and the receiver. The transmission ranks, i.e.\ the number of transmitted streams, and the user scheduling in all cells are jointly optimized in order to maximize a network utility function accounting for fairness among users. A distributed coordinated scheduler motivated by an interference pricing mechanism and relying on a master-slave architecture is introduced. The proposed scheme is operated based on the user report of a recommended rank for the interfering cells accounting for the receiver interference suppression capability. It incurs a very low feedback and backhaul overhead and enables efficient link adaptation. It is moreover robust to channel measurement errors and applicable to both open-loop and closed-loop MIMO operations. A 20% cell edge performance gain over uncoordinated LTE-A system is shown through system level simulations.Comment: IEEE Transactions or Wireless Communications, Accepted for Publicatio

Specification of downlink-fixed reference channel DL-FRC for 5G new radio technology

The next generation for mobile communication is new radio (NR) that supporting air interface which referred to the fifth generation or 5G. Long term evolution (LTE), universal mobile telecommunications system (UMTS), and global system for mobile communication (GSM) are 5G NR predecessors, also referred to as fourth generation (4G), third generation (3G) and second generation (2G) technologies. Pseudo-noise (PN) code length and modulation technique used in the 5G technology affect the output spectrum and the payload of DL-FRC specification, in this paper quadrature phase shift keying (QPSK), 16 QAM modulation approaches tested under additive white Gaussian noise (AWGN) in term of bit error rate (BER) which used with 5G technology system implemented with MATLAB-Simulink and programing and, resulting of 1672, 12296 bit/slot payload at frequency range FR1 from 450 MHz-6 GHz and 4424, 20496 bit/slot payload at frequency range FR2 from 24.25 GHz-52.6 GHz, also determining subcarrier spacing, allocated source block, duplex mode, payload bit/slot, RBW (KHz), sampling rate (MHz), the gain and the bandwidth of main, side loop where illustrated

SCMA for Open-Loop Joint Transmission CoMP

Sparse Code Multiple Access (SCMA), a non-orthogonal multiple access scheme, has been introduced as a key 5G technology to improve spectral efficiency. In this work, we propose SCMA to enable open-loop coordinated multipoint (CoMP) joint transmission (JT). The scheme combines CoMP techniques with multi-user SCMA (MU-SCMA) in downlink. This scheme provides open-loop user multiplexing and JT in power and code domains, with robustness to mobility and low overhead of channel state information (CSI) acquisition. The combined scheme is called MU-SCMA-CoMP, in which SCMA layers and transmit power of multiple transmit points (TPs) are shared among multiple users while a user may receive multiple SCMA layers from multiple TPs within a CoMP cluster. The benefits of the proposed scheme includes: i) drastic overhead reduction of CSI acquisition, ii) significant increase in throughput and coverage, and iii) robustness to channel aging. Various algorithms of MU-SCMA-CoMP are presented, including the detection strategy, power sharing optimization, and scheduling. System level evaluation shows that the proposed schemes provide significant throughput and coverage gains over OFDMA for both pedestrian and vehicular users

LTE-Advanced radio access enhancements: A survey

Long Term Evolution Advanced (LTE-Advanced) is the next step in LTE evolution and allows operators to improve network performance and service capabilities through smooth deployment of new techniques and technologies. LTE-Advanced uses some new features on top of the existing LTE standards to provide better user experience and higher throughputs. Some of the most significant features introduced in LTE-Advanced are carrier aggregation, enhancements in heterogeneous networks, coordinated multipoint transmission and reception, enhanced multiple input multiple output usage and deployment of relay nodes in the radio network. Mentioned features are mainly aimed to enhance the radio access part of the cellular networks. This survey article presents an overview of the key radio access features and functionalities of the LTE-Advanced radio access network, supported by the simulation results. We also provide a detailed review of the literature together with a very rich list of the references for each of the features. An LTE-Advanced roadmap and the latest updates and trends in LTE markets are also presented

Evaluating the effectiveness of Cooperative/Coordinated Multipoint (CoMP) LTE feature in uplink and downlink transmissions

Shannon demonstrated that the channel capacity depends of the ratio of the received signal power to interference plus noise power (SINR). Inter-cell interference caused by neighbouring base stations (BSs) has been identified as one of the most severe problem towards the deployment of LTE technology as it can significantly deteriorate the performance of cellside User Equipment (UE). However, because of regulatory and radiation restrictions as well as operational costs, signal power may only be increased only up to a certain limit to reduce the interference. The other common radio propagation impairment is multipath. Multipath refers to a scenario where multiple copies of a signal propagate to a receiver using different paths. The paths can be created due to signal reflection, scattering and diffraction. As will be discussed later the effects of multipath contribute little to intercell interference because multipath characteristics such as delay spread are compensated for using cyclic prefixes. In this work, we will limit our scope to interference as it has been identified as the main cause of performance degradation for cell edge users due to the full frequency reuse technique used in LTE. To mitigate interference 3GPP devised options of increasing the capacity in LTEAdvanced Release 12 which include the use of spectral aggregation, employing Multiple Input and Multiple Output (MIMO) Antenna techniques, deploying more base stations and micro and femto cells, increasing the degree of sectorisation and Coordinated Multipoint (CoMP). We are primarily interested in evaluating performance improvements introduced when uplink (UL) and downlink (DL) coordinated/cooperative multipoint (CoMP) is enabled in LTE Advanced Release 12 as a way of reducing interference among sites. The CoMP option of reducing interference does not require deployment of new equipment compared to the other options mentioned above hence network deployment costs are minimal. CoMP in theory is known to reduce interference especially for cell edge users and therefore improves network fairness. With CoMP, multiple points coordinate with each other such that transmission of signals to and from other points do not incur serious interference or the interference can even be exploited as a meaningful signal. In September 2011 work on specifications for CoMP support was started in 3GPP LTEAdvanced as one of the core features in LTE-Advanced Release 11 to improve cell edge user throughput as well as the average network throughput. We set to do field measurements in the evaluation of the effectiveness of CoMP in LTE. 3GPP LTE Release 12 was used and cell edge users' performance was the focus. The network operates in 2330 - 2350 MHz band (Channel 40). From the field measurements, it was demonstrated that the CoMP (Scenario 2) feature indeed effective in improving service quality/user experience/fairness for cell edge users. CoMP inherently improves network capacity. A seven (7) percent throughput was noticed

Scheduler Algorithms for MU-MIMO

In multi-user multiple input multiple output (MU-MIMO), the complexity of the base-station scheduler has increased further compared to single-user multiple input multiple output (SU-MIMO). The scheduler must understand if several users can be spatially multiplexed in the same time-frequency resource. One way to spatially separate users is through beamforming with sufficiently many antennas. In this thesis work, two downlink beamforming algorithms for MU-MIMO are studied: The first algorithm implements precoding without considering inter-cell interference (ICI). The second one considers it and attempts to mitigate or null transmissions in the direction of user equipments (UEs) in other cells. The two algorithms are evaluated in SU-MIMO and MU-MIMO setups operating in time division duplex (TDD) mode and serving with single and dual-antenna terminals. Full-Buffer (FB) and file transfer protocol (FTP) data traffic profiles are studied. Additionally, various UE mobility patterns, UE transmit antenna topologies, sounding reference signal (SRS) periodicity configurations, and uniform linear array (ULA) topologies are considered. Simulations have been performed using a system level simulation framework developed by Ericsson AB. Another important part of this thesis work is the functional verification of this simulation framework, which at the time of writing is still undergoing development. Our simulation results show that in SU-MIMO, the second algorithm, which considers ICI, outperforms the first one for FB traffic profile and all UE speeds, but not for FTP traffic profile and medium (30 km/h) or high (60 km/h) UE speeds. In this case, the first algorithm, which does not consider ICI, can be used with advantage. In MU-MIMO, cell downlink throughput gains are observed for the second algorithm over the first one for low and medium system loads (number of users). For both algorithms, the cell throughput is observed to decrease with increasing UE speed and sounding periodicity.Scheduling in modern wireless standards, e.g., 3G, 4G and future 5G, can be defined as the task of allocating time and frequency resources by the base station (BS) to each user equipment (UE) that wants to engage in communication. Resources are allocated every transmission time interval (TTI), which is typically one millisecond. There exist both uplink (from the UEs to the BS) and downlink (from the BS to the UEs) resource schedulers implemented in the e-Node B, i.e., the base station (BS) in Long Term Evolution (LTE). The aim of this thesis work is to study how various communication techniques proposed for 5G can increase the overall system throughput of the downlink (DL) when a realistic resource scheduler is used. In particular, we consider: (i) Beamforming, (ii) Multi-user multiple input multiple output (MU-MIMO), and (iii) Inter-cell interference (ICI) mitigation. Beamforming can be achieved by deploying a large number of antenna elements at the BS with the aim of increasing the signal to interference noise ratio (SINR) towards the UE. Contrary to single-user multiple input multiple output (SU-MIMO), in MU-MIMO more than one UE are scheduled for transmissions in the same time-frequency resource; this is possible by judiciously pairing various UEs which are spatially sufficiently separated (according to some metric that we will define later). ICI mitigation can be achieved by means of proper precoding at BS where the precoder attempts to mitigate the interfering signal from BS towards UEs belonging to neighboring cells. In this thesis work, we investigate the performance of two scheduler algorithms for MU-MIMO, using SU-MIMO as baseline. The first algorithm does not consider ICI while the second one does. Dual layer beamforming (that is, two independent data streams are transmitted to each UE) and time division duplex (TDD) are assumed. In TDD mode the BS acquires the channel information from sounding reference signals (SRS) transmitted in the uplink (UL) and, by virtue of channel reciprocity, reuses the so-obtained channel information in the downlink. The performance evaluation of the two algorithms is based on the following parameters: UE Traffic profile, UE speed, SRS UL antenna configuration, SRS parameters, and BS antenna topology. - UE speed includes 3,30, and 60 km/h. - UE traffic profile includes full-buffer (FB) and file transfer protocol (FTP). With FB traffic profile, UEs send/receive data to/from the BS all the time, while this is not the case in the FTP traffic profile case. Some examples of FTP traffic profiles may include chatty, video, VoIP, web, etc. - SRS UL antenna configuration includes: (i) Two SRS, in which each UE sends two SRS to the BS from two antennas, (ii) one SRS with antenna selection, in which each UE alternately sends one SRS to the BS from each of two antennas, and (iii) one SRS without antenna selection, in which each UE sends one SRS to the BS from only one antenna. For two SRS UE case (note that in the downlink two layers, and hence two UE antennas, are always used). - SRS parameters include SRS bandwidth and SRS periodicity. In this thesis work, full-bandwidth SRS (20 MHz) with various SRS periodicities such as 5 ms, 10 ms, 20 ms are considered. - BS antenna topology includes 8 and 64 antenna elements at the BS. The main result of this thesis work is that in both SU-MIMO and MU-MIMO with FB traffic profile, it is better to use the second algorithm which considers ICI rather than the first one which does not. However, with FTP traffic profile, this is not always the case

A Flexible mmWave Layer 2 Protocol Implementation for Integrated Access and Backhaul Architecture

. This work was supported in part by the Spanish Ministry of Science, Innovation and Universities funded by MCIN/AEI/10.13039/501100011033 under Project PID2020-113979RB-C21; and in part by the Ministry of Economic Affairs and Digital Transformation and the European Union-NextGenerationEU under Project TSI-063000-2021-83 (DISRADIO). The work of Randy Verdecia-Peña was supported by the Ministry of Science and Innovation under Contract PRE2018-085032. Publisher Copyright: © 2013 IEEEIn this paper, we present a 3GPP-inspired hardware implementation for the out-of-band Integrated Access and Backhaul (IAB) network, which serves as a solution to both coverage extension and capacity boosting in 5G and beyond networks. By employing an Ettus x310 software-defined radio (SDR) board, Pasternack's 60 GHz Transmitter (Tx) waveguide module, and MatlabTM software, we design and develop an easy-to-use out-of-band mmWave Layer 2 protocol. The proposed protocol decodes a frequency range 1 (FR1) 5G signal as input at 3.5 GHz, which is retransmitted to the UE as a frequency range 2 (FR2) 5G signal at 60 GHz. In the implementation of the Layer 2 protocol, the least squares (LS) estimator is adopted by considering the demodulation reference signal (DM-RS) and the channel state information reference signal (CSI-RS) as pilot symbols in real-world environments. To alleviate the performance degradation in the mmWave access link, a phase noise cancellation (PNC) algorithm based on the phase tracking reference signal (PT-RS) is implemented at the UE node where a PT-RS block structure is introduced in the mmWave Layer 2 protocol transmitter stage. We review and evaluate the key performance indicators (KPIs) of the proposed Layer 2 protocol in real non-line-of-sight (NLOS) environments and a comparison between the gNode-to-UE link is carried out. Our results indicate that the performance of the proposed Layer 2 protocol is similar to the obtained with the off-the-shelf equipment demonstrating the right functionality of the developed algorithms. Experimental results evidence the superiority of the proposed Layer 2 protocol over the gNodeB-to-UE link (direct link communication) and the best performance is obtained when the PNC algorithm is considered in the IAB architecture.publishersversionpublishe

A survey of machine learning techniques applied to self organizing cellular networks

In this paper, a survey of the literature of the past fifteen years involving Machine Learning (ML) algorithms applied to self organizing cellular networks is performed. In order for future networks to overcome the current limitations and address the issues of current cellular systems, it is clear that more intelligence needs to be deployed, so that a fully autonomous and flexible network can be enabled. This paper focuses on the learning perspective of Self Organizing Networks (SON) solutions and provides, not only an overview of the most common ML techniques encountered in cellular networks, but also manages to classify each paper in terms of its learning solution, while also giving some examples. The authors also classify each paper in terms of its self-organizing use-case and discuss how each proposed solution performed. In addition, a comparison between the most commonly found ML algorithms in terms of certain SON metrics is performed and general guidelines on when to choose each ML algorithm for each SON function are proposed. Lastly, this work also provides future research directions and new paradigms that the use of more robust and intelligent algorithms, together with data gathered by operators, can bring to the cellular networks domain and fully enable the concept of SON in the near future