Wide I/O Dram Architecture Utilizing Proximity Communication

The bandwidth and power consumption of dynamic random access memory, used as the main memory of a computer system, impacts the computer’s execution rate even with the existence of a memory hierarchy. DRAM manufacturers focus on density increases due to the innate price per bit decline of main memory while processor manufacturers continually focus on boosting performance by increasing the number of instructions completed per second. This leads to a performance gap between the microprocessor and DRAM. Proximity communication promises to increase the I/O density of DRAM products while reducing the power consumption of the main memory system. This thesis develops and discusses the design of a memory system employing 4 Gb DRAM chips with a 64-bit wide communication bus using proximity communication. Technological roadblocks are analyzed and novel solutions are proposed. The proposed 4 Gb DRAM architecture can reduce the power consumption of a main memory system by 50% while increasing the bandwidth by 100%. The 4 Gb chip developed in this thesis measures 68.88 mm2 and has an array efficiency of 59.9%. These estimates are comparable to the 2012 International Technology Roadmap for Semiconductors’ estimates of 74 mm2 and 56%, respectfully

Performance Analysis of a 3D Wireless Massively Parallel Computer

In previous work, the authors presented a 3D hexagonal wireless direct-interconnect network for a massively parallel computer, with a focus on analysing processor utilisation. In this study, we consider the characteristics of such an architecture in terms of link utilisation and power consumption. We have applied a store-and-forward packet-switching algorithm to both our proposed architecture and a traditional wired 5D direct network (the same as IBM’s Blue Gene). Simulations show that for small and medium-size networks the link utility of the proposed architecture is comparable with (and in some cases even better than) traditional 5D networks. This work demonstrates that there is a potential for wireless processing array concepts to address High-Performance Computing (HPC) challenges whilst alleviating some significant physical construction drawbacks of traditional systems

Wireless Testing of Integrated Circuits.

Integrated circuits (ICs) are usually tested during manufacture by means of automatic testing equipment (ATE) employing probe cards and needles that make repeated physical contact with the ICs under test. Such direct-contact probing is very costly and imposes limitations on the use of ATE. For example, the probe needles must be frequently cleaned or replaced, and some emerging technologies such as three-dimensional ICs cannot be probed at all. As an alternative to conventional probe-card testing, wireless testing has been proposed. It mitigates many of the foregoing problems by replacing probe needles and contact points with wireless communication circuits. However, wireless testing also raises new problems which are poorly understood such as: What is the most suitable wireless communication technique to employ, and how well does it work in practice? This dissertation addresses the design and implementation of circuits to support wireless testing of ICs. Various wireless testing methods are investigated and evaluated with respect to their practicality. The research focuses on near-field capacitive communication because of its efficiency over the very short ranges needed during IC manufacture. A new capacitive channel model including chip separation, cross-talk, and misalignment effects is proposed and validated using electro-magnetic simulation studies to provide the intuitions for efficient antenna and circuit design. We propose a compact clock and data recovery architecture to avoid a dedicated clock channel. An analytical model which predicts the DC-level fluctuation due to the capacitive channel is presented. Based on this model, feed-forward clock selection is designed to enhance performance. A method to select proper channel termination is discussed to maximize the channel efficiency for return-to-zero signaling. Two prototype ICs incorporating wireless testing systems were fabricated and tested with the proposed methods of testing digital circuits. Both successfully demonstrated gigahertz communication speeds with a bit-error rate less than 10^−11. A third prototype IC containing analog voltage measurement circuits was implemented to determine the feasibility of wirelessly testing analog circuits. The fabricated prototype achieved satisfactory voltage measurement with 1 mV resolution. Our work demonstrates the validity of the proposed models and the feasibility of near-field capacitive communication for wireless testing of ICs.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/93993/1/duelee_1.pd

Evaluating Techniques for Wireless Interconnected 3D Processor Arrays

In this thesis the viability of a wireless interconnect network for a highly parallel computer is investigated. The main theme of this thesis is to project the performance of a wireless network used to connect the processors in a parallel machine of such design. This thesis is going to investigate new design opportunities a wireless interconnect network can offer for parallel computing. A simulation environment is designed and implemented to carry out the tests. The results have shown that if the available radio spectrum is shared effectively between building blocks of the parallel machine, there are substantial chances to achieve high processor utilisation. The results show that some factors play a major role in the performance of such a machine. The size of the machine, the size of the problem and the communication and computation capabilities of each element of the machine are among those factors. The results show these factors set a limit on the number of nodes engaged in some classes of tasks. They have shown promising potential for further expansion and evolution of our idea to new architectural opportunities, which is discussed by the end of this thesis. To build a real machine of this type the architects would need to solve a number of challenging problems including heat dissipation, delivering electric power and Chip/board design; however, these issues are not part of this thesis and will be tackled in future