A General Framework for Analyzing, Characterizing, and Implementing Spectrally Modulated, Spectrally Encoded Signals

Fourth generation (4G) communications will support many capabilities while providing universal, high speed access. One potential enabler for these capabilities is software defined radio (SDR). When controlled by cognitive radio (CR) principles, the required waveform diversity is achieved via a synergistic union called CR-based SDR. Research is rapidly progressing in SDR hardware and software venues, but current CR-based SDR research lacks the theoretical foundation and analytic framework to permit efficient implementation. This limitation is addressed here by introducing a general framework for analyzing, characterizing, and implementing spectrally modulated, spectrally encoded (SMSE) signals within CR-based SDR architectures. Given orthogonal frequency division multiplexing (OFDM) is a 4G candidate signal, OFDM-based signals are collectively classified as SMSE since modulation and encoding are spectrally applied. The proposed framework provides analytic commonality and unification of SMSE signals. Applicability is first shown for candidate 4G signals, and resultant analytic expressions agree with published results. Implementability is then demonstrated in multiple coexistence scenarios via modeling and simulation to reinforce practical utility

Chinese cellular telecommunications in the past and the 21st century

Cellular telecommunication technology is one of the hottest topics of the last two decades. The annual rate of user growth is more than 30 percent. It began with the first generation (1G) networks and bloomed with second generation (2G) of cellular technologies. New third generation cellular (3G) technologies aim at offering high-speed, superior-quality information service to mobile subscribers. [2] The Chinese cellular market is developing with unbelievable speed. China launched its first cellular network in 1987. At the end of 2002, it was the biggest wireless market in the world, with more than 200 million subscribers. [56] Technologies used in the migration from the 2G networks to the 3G networks are referred to as 2.5 generation or 2.5G. It is no doubt that the 3G pattern selected in China will deeply affect the competition among the 3G technologies. This thesis will forecast the 3G systems to be selected for use in China. It will begin with the 1G and 2G networks and then look into the 2.5 G and the 3G cellular telecommunication technologies in more detail. Analysis the history, culture and business conditions in China will follow. Finally, this paper will make a prediction of the principal Chinese 3G technologies that will be chosen based on analyzing concrete information. An examination of other Asia markets, such as the 3G markets in Japan, and South Korea will be included. The conclusion of this thesis is that WCDMA (Wideband Code Division Multiple Access), a 3G technology that is developed and supported by European telecommunication manufacturers, will take the lion\u27s share of the Chinese 3G market, about 65% to 70%. Another technology, CDMA2000, will take more than 20% of the Chinese 3G market share. There is also a Chinese oriented 3G technology named TD-SCDMA (Time Division Synchronous Code Division Multiple Access). With the Chinese government\u27s support, it will collect the remaining 10% to 15% market share

A Link-Level Simulator of the cdma2000 Reverse-Link Physical Layer.

The cdma2000 system is an evolutionary enhancement of the IS-95 standards which support 3G services defined by the International Telecommunications Union (ITU). cdma2000 comes in two phases: 1XRTT and 3XRTT (1X and 3X indicates the number of 1.25 MHz wide radio carrier channels used and RTT stands for Radio Transmission Technology). The cdma2000 1XRTT, which operates within a 1.25 MHz bandwidth, can be utilized in existing IS-95 CDMA channels as it uses the same bandwidth, while 3XRTT requires the commitment of 5 MHz bandwidth to support higher data rates. This paper describes a software model implementation of the cdma2000 reverse link and its application for evaluating the effect of rake receiver design parameters on the system performance under various multipath fading conditions. The cdma2000 models were developed at the National Institute of Standards and Technology (NIST), using SPW (Signal Processing Worksystem) commercial software tools. The model has been developed in a generic manner that includes all the reverse link six radio configurations and their corresponding data rates, according to cdma2000 specifications. After briefly reviewing the traffic channel characteristics of the cdma2000 reverse link (subscriber to base station), the paper discusses the rake receiver implementation including an ideal rake receiver. It then evaluates the performance of each receiver for a Spreading Rate 3 (3XRTT) operation, which is considered as a true "3G" cdma2000 technology. These evaluations are based on the vehicular IMT-2000 (International Mobile Telecommunication 2000) channel model using the link budget defined in cdma2000 specifications for the reverse link

Esquemas de pré-codificação IA com IB-DFE para sistemas MC-CDMA

Mestrado em Engenharia Eletrónica e TelecomunicaçõesTo achieve high bit rates, needed to meet the quality of service requirements of future multimedia applications, multi-carrier code division multiple access (MC-CDMA) has been considered as a candidate air-interface. Interference alignment (IA) is a promising technique that allows high capacity gains in interfering channels. On the other hand, iterative block decision feedback equalization (IB-DFE) based receivers can efficiently exploit the inherent space-frequency diversity of the MIMO MC-CDMA systems. In this thesis we proposed an IA precoding at the transmitter with IB-DFE based processing at the receiver for MC-CDMA systems. The IA precoding is applied at chip level instead of the data symbols level, as in the conventional IA based systems. The receiver is designed in two steps: first the equalizers based on zero forcing (ZF) or minimum mean square error (MMSE) are used to remove the aligned users´ interference. Then and after a whitening noise process, an IB-DFE based equalizer is designed to remove both the residual inter-user aligned and inter-carrier interferences. The results have shown that the obtained performance is very close to the one obtained by the optimal matched filter, with few iterations at the receiver side.Para atingir maiores ritmos de transmissão, as futures aplicações multimédia necessitam de atingir a qualidade de serviço necessária. Para isso, o multi-carrier code division multiple access (MC-CDMA) tem sido apontado como um forte candidato para interface ar dos futuros sistemas celulares. O Interference Alignment (IA) ou alinhamento de interferência é uma técnica promissora que permite ter altos ganhos de capacidade em canais com interferência. Por outro lado, temos receptores baseados no conceito iterative block decision feedback equalization(IB-DFE) que conseguem tirar partido, de uma forma eficiente, da inerente diversidade espaço-frequência dos sistemas MIMO MC-CDMA. Nesta dissertação é implementada uma pré-codificação baseada no conceito de IA considerando três transmissores (ou estações base) juntamente, com um processamento IB-DFE no receptor para sistemas MC-CDMA.A pré-codificação é aplicada ao nível de chip em vez de ser aplicado ao nível dos dados. O receptor é projectado em dois passos: em primeiro lugar equalizadores baseados em ZF ou em MMSE são utilizados para remover a interferência alinhada dos restantes utilizadores. De seguida, e após aplicar um processo de branqueamento do ruído ao sinal à saída do primeiro equalizador, um segundo equalizador baseado em IB-DFE é projectado para remover a interferência inter-utilizador residual e também a interferência residual entre portadoras. Os resultados obtidos mostraram-se satisfatórios na remoção da interferência obtendo-se um desempenho muito próximo do obtido considerando um filtro adaptado

Flat Cellular (UMTS) Networks

Traditionally, cellular systems have been built in a hierarchical manner: many specialized cellular access network elements that collectively form a hierarchical cellular system. When 2G and later 3G systems were designed there was a good reason to make system hierarchical: from a cost-perspective it was better to concentrate traffic and to share the cost of processing equipment over a large set of users while keeping the base stations relatively cheap. However, we believe the economic reasons for designing cellular systems in a hierarchical manner have disappeared: in fact, hierarchical architectures hinder future efficient deployments. In this paper, we argue for completely flat cellular wireless systems, which need just one type of specialized network element to provide radio access network (RAN) functionality, supplemented by standard IP-based network elements to form a cellular network. While the reason for building a cellular system in a hierarchical fashion has disappeared, there are other good reasons to make the system architecture flat: (1) as wireless transmission techniques evolve into hybrid ARQ systems, there is less need for a hierarchical cellular system to support spatial diversity; (2) we foresee that future cellular networks are part of the Internet, while hierarchical systems typically use interfaces between network elements that are specific to cellular standards or proprietary. At best such systems use IP as a transport medium, not as a core component; (3) a flat cellular system can be self scaling while a hierarchical system has inherent scaling issues; (4) moving all access technologies to the edge of the network enables ease of converging access technologies into a common packet core; and (5) using an IP common core makes the cellular network part of the Internet

LTE-verkon suorituskyvyn parantaminen CDMA2000:sta LTE:hen tehdyn muutoksen jälkeen

CDMA2000 technology has been widely used on 450 MHz band. Recently the equipment availability and improved performance offered by LTE has started driving the operators to migrate their networks from CDMA2000 to LTE. The migration may cause the network performance to be in suboptimal state. This thesis presents four methods to positively influence LTE network performance after CDMA2000 to LTE migration, especially on 450 MHz band. Furthermore, three of the four presented methods are evaluated in a live network. The measured three methods were cyclic prefix length, handover parameter optimization and uplink coordinated multipoint (CoMP) transmission. The objective was to determine the effectiveness of each method. The research methods included field measurements and network KPI collection. The results show that normal cyclic prefix length is enough for LTE450 although the cell radius may be up to 50km. Only special cases exist where cyclic prefix should be extended. Operators should consider solving such problems individually instead of widely implementing extended cyclic prefix. Handover parameter optimization turned out to be an important point of attention after CDMA2000 to LTE migration. It was observed that if the handover parameters are not concerned, significant amount of unnecessary handovers may happen. It was evaluated that about 50% of the handovers in the network were unnecessary in the initial situation. By adjusting the handover parameter values 47,28 % of the handovers per user were removed and no negative effects were detected. Coordinated multipoint transmission has been widely discussed to be an effective way to improve LTE network performance, especially at the cell edges. Many challenges must be overcome before it can be applied to downlink. Also, implementing it to function between cells in different eNBs involve challenges. Thus, only intra-site uplink CoMP transmission was tested. The results show that the performance improvements were significant at the cell edges as theory predicted.CDMA2000 teknologiaa on laajalti käytetty 450 MHz:n taajuusalueella. Viime aikoina LTE:n tarjoamat halvemmat laitteistot ja parempi suorituskyky ovat kannustaneet operaattoreita muuttamaan verkkoaan CDMA2000:sta LTE:hen. Kyseinen muutos saattaa johtaa epäoptimaaliseen tilaan verkon suorituskyvyn kannalta. Tämä työ esittelee neljä menetelmää, joilla voidaan positiivisesti vaikuttaa LTE-verkon suorituskykyyn CDMA2000:ste LTE:hen tehdyn muutoksen jälkeen erityisesti 450 MHz:n taajuusalueella. Kolmea näistä menetelmistä arvioidaan tuotantoverkossa. Nämä kolme menetelmää ovat suojavälin pituus, solunvaihtoparametrien optimointi ja ylälinkin koordinoitu monipistetiedonsiirto. Tavoite oli määrittää kunkin menetelmän vaikutus. Tutkimusmenetelmiin kuului kenttämittaukset ja verkon suorituskykymittareiden analyysi. Tutkimustulosten perusteella voidaan sanoa, että normaali suojaväli on riittävän pitkä LTE450:lle vaikka solujen säde on jopa 50km. Vain erikoistapauksissa tarvitaan pidennettyä suojaväliä. Operaattoreiden tulisi ratkaista tällaiset tapaukset yksilöllisesti sen sijaan, että koko verkossa käytettäisiin pidennettyä suojaväliä. Solunvaihtoparametrien optimointi osoittautui tärkeäksi huomion aiheeksi CDMA2000:sta LTE:hen tehdyn muutoksen jälkeen. Turhia solunvaihtoja saattaa tapahtua merkittäviä määriä, mikäli parametreihin ei kiinnitetä huomiota. Lähtötilanteessa noin 50 % testiverkon solunvaihdoista arvioitiin olevan turhia. Solunvaihtoparametreja muuttamalla 47,28 % solunvaihdoista per käyttäjä saatiin poistettua ilman, että mitään haittavaikutuksia olisi huomattu. Koordinoidun monipistetiedonsiirron on laajalti sanottu olevan tehokas tapa parantaa LTE-verkon suorituskykyä, etenkin solujen reunoilla. Monia haasteita pitää ratkaista, enne kuin sitä voidaan käyttää alalinkin tiedonsiirtoon. Lisäksi sen käyttöön eri tukiasemien solujen välillä liittyy haasteita. Tästä syystä monipistetiedonsiirtoa voitiin testata vain ylälinkin suuntaan ja vain yhden tukiaseman välisten solujen kesken. Tulokset osoittivat, että suorituskyky parani merkittävästi solun reunalla

Power control for WCDMA

This project tries to introduce itself in the physical implementations that make possible the denominated third generation mobile technology. As well as to know the technology kind that makes possible, for example, a video-call in real time. During this project, the different phases passed from the election of WCDMA like the access method for UMTS will appear. Its coexistence with previous network GSM will be analyzed, where the compatibility between systems has been one of the most important aspects in the development of WCDMA, the involved standardization organisms in the process, as well as the different protocols that make the mobile communications within a network UTRAN possible. Special emphasis during the study of the great contribution that has offered WCDMA with respect to the control of power of the existing signals will be made. The future lines that are considered in the present, and other comment that already are in their last phase of development in the field of the mobile technology. UMTS through WCDMA can be summarized like a revolution of the air interface accompanied by a revolution in the network of their architecture

Linear space-time modulation in multiple-antenna channels

This thesis develops linear space–time modulation techniques for (multi-antenna) multi-input multi-output (MIMO) and multiple-input single-output (MISO) wireless channels. Transmission methods tailored for such channels have recently emerged in a number of current and upcoming standards, in particular in 3G and "beyond 3G" wireless systems. Here, these transmission concepts are approached primarily from a signal processing perspective. The introduction part of the thesis describes the transmit diversity concepts included in the WCDMA and cdma2000 standards or standard discussions, as well as promising new transmission methods for MIMO and MISO channels, crucial for future high data-rate systems. A number of techniques developed herein have been adopted in the 3G standards, or are currently being proposed for such standards, with the target of improving data rates, signal quality, capacity or system flexibility. The thesis adopts a model involving matrix-valued modulation alphabets, with different dimensions usually defined over space and time. The symbol matrix is formed as a linear combination of symbols, and the space-dimension is realized by using multiple transmit and receive antennas. Many of the transceiver concepts and modulation methods developed herein provide both spatial multiplexing gain and diversity gain. For example, full-diversity full-rate schemes are proposed where the symbol rate equals the number of transmit antennas. The modulation methods are developed for open-loop transmission. Moreover, the thesis proposes related closed-loop transmission methods, where space–time modulation is combined either with automatic retransmission or multiuser scheduling.reviewe

Macroscopic Diversity Applications of Mult-input Multi-output (Mimo) Systems for Broadband Mobile Communication

Electrical Engineerin

Performance Comparison of Dual Connectivity and Hard Handover for LTE-5G Tight Integration in mmWave Cellular Networks

MmWave communications are expected to play a major role in the Fifth generation of mobile networks. They offer a potential multi-gigabit throughput and an ultra-low radio latency, but at the same time suffer from high isotropic pathloss, and a coverage area much smaller than the one of LTE macrocells. In order to address these issues, highly directional beamforming and a very high-density deployment of mmWave base stations were proposed. This Thesis aims to improve the reliability and performance of the 5G network by studying its tight and seamless integration with the current LTE cellular network. In particular, the LTE base stations can provide a coverage layer for 5G mobile terminals, because they operate on microWave frequencies, which are less sensitive to blockage and have a lower pathloss. This document is a copy of the Master's Thesis carried out by Mr. Michele Polese under the supervision of Dr. Marco Mezzavilla and Prof. Michele Zorzi. It will propose an LTE-5G tight integration architecture, based on mobile terminals' dual connectivity to LTE and 5G radio access networks, and will evaluate which are the new network procedures that will be needed to support it. Moreover, this new architecture will be implemented in the ns-3 simulator, and a thorough simulation campaign will be conducted in order to evaluate its performance, with respect to the baseline of handover between LTE and 5G.Comment: Master's Thesis carried out by Mr. Michele Polese under the supervision of Dr. Marco Mezzavilla and Prof. Michele Zorz