Comparative evaluation of approaches in T.4.1-4.3 and working definition of adaptive module

The goal of this deliverable is two-fold: (1) to present and compare different approaches towards learning and encoding movements us- ing dynamical systems that have been developed by the AMARSi partners (in the past during the first 6 months of the project), and (2) to analyze their suitability to be used as adaptive modules, i.e. as building blocks for the complete architecture that will be devel- oped in the project. The document presents a total of eight approaches, in two groups: modules for discrete movements (i.e. with a clear goal where the movement stops) and for rhythmic movements (i.e. which exhibit periodicity). The basic formulation of each approach is presented together with some illustrative simulation results. Key character- istics such as the type of dynamical behavior, learning algorithm, generalization properties, stability analysis are then discussed for each approach. We then make a comparative analysis of the different approaches by comparing these characteristics and discussing their suitability for the AMARSi project

Calibration of the NuSTAR High Energy Focusing X-ray Telescope

We present the calibration of the \textit{Nuclear Spectroscopic Telescope Array} (\nustar) X-ray satellite. We used the Crab as the primary effective area calibrator and constructed a piece-wise linear spline function to modify the vignetting response. The achieved residuals for all off-axis angles and energies, compared to the assumed spectrum, are typically better than $\pm 2$\% up to 40\,keV and 5--10\,\% above due to limited counting statistics. An empirical adjustment to the theoretical 2D point spread function (PSF) was found using several strong point sources, and no increase of the PSF half power diameter (HPD) has been observed since the beginning of the mission. We report on the detector gain calibration, good to 60\,eV for all grades, and discuss the timing capabilities of the observatory, which has an absolute timing of $\pm$ 3\,ms. Finally we present cross-calibration results from two campaigns between all the major concurrent X-ray observatories (\textit{Chandra}, \textit{Swift}, \textit{Suzaku} and \textit{XMM-Newton}), conducted in 2012 and 2013 on the sources 3C\,273 and PKS\,2155-304, and show that the differences in measured flux is within $\sim$10\% for all instruments with respect to \nustar

Architectural level delay and leakage power modelling of manufacturing process variation

PhD ThesisThe effect of manufacturing process variations has become a major issue regarding the estimation of circuit delay and power dissipation, and will gain more importance in the future as device scaling continues in order to satisfy market place demands for circuits with greater performance and functionality per unit area. Statistical modelling and analysis approaches have been widely used to reflect the effects of a variety of variational process parameters on system performance factor which will be described as probability density functions (PDFs). At present most of the investigations into statistical models has been limited to small circuits such as a logic gate. However, the massive size of present day electronic systems precludes the use of design techniques which consider a system to comprise these basic gates, as this level of design is very inefficient and error prone. This thesis proposes a methodology to bring the effects of process variation from transistor level up to architectural level in terms of circuit delay and leakage power dissipation. Using a first order canonical model and statistical analysis approach, a statistical cell library has been built which comprises not only the basic gate cell models, but also more complex functional blocks such as registers, FIFOs, counters, ALUs etc. Furthermore, other sensitive factors to the overall system performance, such as input signal slope, output load capacitance, different signal switching cases and transition types are also taken into account for each cell in the library, which makes it adaptive to an incremental circuit design. The proposed methodology enables an efficient analysis of process variation effects on system performance with significantly reduced computation time compared to the Monte Carlo simulation approach. As a demonstration vehicle for this technique, the delay and leakage power distributions of a 2-stage asynchronous micropipeline circuit has been simulated using this cell library. The experimental results show that the proposed method can predict the delay and leakage power distribution with less than 5% error and at least 50,000 times faster computation time compare to 5000-sample SPICE based Monte Carlo simulation. The methodology presented here for modelling process variability plays a significant role in Design for Manufacturability (DFM) by quantifying the direct impact of process variations on system performance. The advantages of being able to undertake this analysis at a high level of abstraction and thus early in the design cycle are two fold. First, if the predicted effects of process variation render the circuit performance to be outwith specification, design modifications can be readily incorporated to rectify the situation. Second, knowing what the acceptable limits of process variation are to maintain design performance within its specification, informed choices can be made regarding the implementation technology and manufacturer selected to fabricate the design

A Latent Variable Approach to Multivariate Quantitative Trait Loci

A novel approach based on latent variable modelling is presented for the analysis of multivariate quantitative and qualitative trait loci. The approach is general in the sense that it enables the joint analysis of many kinds of quantitative and qualitative traits (including count data and censored traits) in a single modelling framework. In the framework, the observations are modelled as functions of latent variables, which are then affected by quantitative trait loci. Separating the analysis in this way means that measurement errors in the phenotypic observations can be included easily in the model, providing robust inferences. The performance of the method is illustrated using two real multivariate datasets, from barley and Scots pine