Measuring gravitational waves from binary black hole coalescences: II. the waves' information and its extraction, with and without templates

We discuss the extraction of information from detected binary black hole (BBH) coalescence gravitational waves, focusing on the merger phase that occurs after the gradual inspiral and before the ringdown. Our results are: (1) If numerical relativity simulations have not produced template merger waveforms before BBH detections by LIGO/VIRGO, one can band-pass filter the merger waves. For BBHs smaller than about 40 solar masses detected via their inspiral waves, the band pass filtering signal to noise ratio indicates that the merger waves should typically be just barely visible in the noise for initial and advanced LIGO interferometers. (2) We derive an optimized (maximum likelihood) method for extracting a best-fit merger waveform from the noisy detector output; one "perpendicularly projects" this output onto a function space (specified using wavelets) that incorporates our prior knowledge of the waveforms. An extension of the method allows one to extract the BBH's two independent waveforms from outputs of several interferometers. (3) If numerical relativists produce codes for generating merger templates but running the codes is too expensive to allow an extensive survey of the merger parameter space, then a coarse survey of this parameter space, to determine the ranges of the several key parameters and to explore several qualitative issues which we describe, would be useful for data analysis purposes. (4) A complete set of templates could be used to test the nonlinear dynamics of general relativity and to measure some of the binary parameters. We estimate the number of bits of information obtainable from the merger waves (about 10 to 60 for LIGO/VIRGO, up to 200 for LISA), estimate the information loss due to template numerical errors or sparseness in the template grid, and infer approximate requirements on template accuracy and spacing.Comment: 33 pages, Rextex 3.1 macros, no figures, submitted to Phys Rev

Engineering studies related to geodetic and oceanographic remote sensing using short pulse techniques

For the Skylab S-193 radar altimeter, data processing flow charts and identification of calibration requirements and problem areas for defined S-193 altimeter experiments are presented. An analysis and simulation of the relationship between one particular S-193 measurement and the parameter of interest for determining the sea surface scattering cross-section are considered. For the GEOS-C radar altimeter, results are presented for system analyses pertaining to signal-to-noise ratio, pulse compression threshold behavior, altimeter measurement variance characteristics, desirability of onboard averaging, tracker bandwidth considerations, and statistical character of the altimeter data in relation to harmonic analysis properties of the geodetic signal

Frequency-modulated continuous-wave LiDAR compressive depth-mapping

We present an inexpensive architecture for converting a frequency-modulated continuous-wave LiDAR system into a compressive-sensing based depth-mapping camera. Instead of raster scanning to obtain depth-maps, compressive sensing is used to significantly reduce the number of measurements. Ideally, our approach requires two difference detectors. % but can operate with only one at the cost of doubling the number of measurments. Due to the large flux entering the detectors, the signal amplification from heterodyne detection, and the effects of background subtraction from compressive sensing, the system can obtain higher signal-to-noise ratios over detector-array based schemes while scanning a scene faster than is possible through raster-scanning. %Moreover, we show how a single total-variation minimization and two fast least-squares minimizations, instead of a single complex nonlinear minimization, can efficiently recover high-resolution depth-maps with minimal computational overhead. Moreover, by efficiently storing only $2m$ data points from $m<n$ measurements of an $n$ pixel scene, we can easily extract depths by solving only two linear equations with efficient convex-optimization methods

Detection of a close supernova gravitational wave burst in a network of interferometers, neutrino and optical detectors

Trying to detect the gravitational wave (GW) signal emitted by a type II supernova is a main challenge for the GW community. Indeed, the corresponding waveform is not accurately modeled as the supernova physics is very complex; in addition, all the existing numerical simulations agree on the weakness of the GW emission, thus restraining the number of sources potentially detectable. Consequently, triggering the GW signal with a confidence level high enough to conclude directly to a detection is very difficult, even with the use of a network of interferometric detectors. On the other hand, one can hope to take benefit from the neutrino and optical emissions associated to the supernova explosion, in order to discover and study GW radiation in an event already detected independently. This article aims at presenting some realistic scenarios for the search of the supernova GW bursts, based on the present knowledge of the emitted signals and on the results of network data analysis simulations. Both the direct search and the confirmation of the supernova event are considered. In addition, some physical studies following the discovery of a supernova GW emission are also mentioned: from the absolute neutrino mass to the supernova physics or the black hole signature, the potential spectrum of discoveries is wide.Comment: Revised version, accepted for publication in Astroparticle Physic

A New Approach to Time Domain Classification of Broadband Noise in Gravitational Wave Data

Broadband noise in gravitational wave (GW) detectors, also known as triggers, can often be a deterrant to the efficiency with which astrophysical search pipelines detect sources. It is important to understand their instrumental or environmental origin so that they could be eliminated or accounted for in the data. Since the number of triggers is large, data mining approaches such as clustering and classification are useful tools for this task. Classification of triggers based on a handful of discrete properties has been done in the past. A rich information content is available in the waveform or 'shape' of the triggers that has had a rather restricted exploration so far. This paper presents a new way to classify triggers deriving information from both trigger waveforms as well as their discrete physical properties using a sequential combination of the Longest Common Sub-Sequence (LCSS) and LCSS coupled with Fast Time Series Evaluation (FTSE) for waveform classification and the multidimensional hierarchical classification (MHC) analysis for the grouping based on physical properties. A generalized k-means algorithm is used with the LCSS (and LCSS+FTSE) for clustering the triggers using a validity measure to determine the correct number of clusters in absence of any prior knowledge. The results have been demonstrated by simulations and by application to a segment of real LIGO data from the sixth science run.Comment: 16 pages, 16 figure

Time domain analysis of switching transient fields in high voltage substations

Switching operations of circuit breakers and disconnect switches generate transient currents propagating along the substation busbars. At the moment of switching, the busbars temporarily acts as antennae radiating transient electromagnetic fields within the substations. The radiated fields may interfere and disrupt normal operations of electronic equipment used within the substation for measurement, control and communication purposes. Hence there is the need to fully characterise the substation electromagnetic environment as early as the design stage of substation planning and operation to ensure safe operations of the electronic equipment. This paper deals with the computation of transient electromagnetic fields due to switching within a high voltage air-insulated substation (AIS) using the finite difference time domain (FDTD) metho

Performance of self bit synchronizers for the detection of anticorrelated binary signals

Self bit synchronizers for detection of anticorrelated binary systems of digital communication system