Novel Single Phase Dc-Ac Inverter Topology With Enhanced Power Quality

Inverters are widely employed in many application such as photovoltaic (PV), uninterruptable power supply (UPS) etc for the conversion of direct current (DC) power to alternating current (AC) power. The key challenges in design and implementation of inverters are the realization of higher efficiency and good quality output power. To achieve these, this thesis presents a novel single phase DC-AC inverter topology with enhanced power quality. In this topology, a switch is connected at the lower arm of the full-bridge switches to control the output voltage across the full-bridge inverter. The switch at the lower arm of the full-bridge controls the output of full-bridge inverter by increasing or reducing the voltage level at the lower arm of the bridge. This switch of lower arm is controlled by a high frequency sinusoidal pulse width modulation (SPWM) switching signal. While the power switches of full-bridge inverter operate with square wave switching signal at a frequency of 50 Hz. The proposed topology produces a clean sinusoidal output waveform with low distortion and with minimum switching losses, thus yielding high quality output at high efficiency. Next, a random switching hybrid pulse width modulation (HPWM) inverter is developed in order to give a comparison between the proposed inverter and the random switching HPWM inverter. Both computer simulation and experiment were carried out to verify the performance of proposed topology. From the presented results, it is shown that proposed topology has superior performance compared to its conventional counterpart

High Power Density, High Efficiency Single Phase Transformer-less Photovoltaic String Inverters

abstract: Two major challenges in the transformer-less, single-phase PV string inverters are common mode leakage currents and double-line-frequency power decoupling. In the proposed doubly-grounded inverter topology with innovative active-power-decoupling approach, both of these issues are simultaneously addressed. The topology allows the PV negative terminal to be directly connected to the neutral, thereby eliminating the common-mode ground-currents. The decoupling capacitance requirement is minimized by a dynamically-variable dc-link with large voltage swing, allowing an all-film-capacitor implementation. Furthermore, the use of wide-bandgap devices enables the converter operation at higher switching frequency, resulting in smaller magnetic components. The operating principles, design and optimization, and control methods are explained in detail, and compared with other transformer-less, active-decoupling topologies. A 3 kVA, 100 kHz single-phase hardware prototype at 400 V dc nominal input and 240 V ac output has been developed using SiC MOSFETs with only 45 μF/1100 V dc-link capacitance. The proposed doubly-grounded topology is then extended for split-phase PV inverter application which results in significant reduction in both the peak and RMS values of the boost stage inductor current and allows for easy design of zero voltage transition. A topological enhancement involving T-type dc-ac stage is also developed which takes advantage of the three-level switching states with reduced voltage stress on the main switches, lower switching loss and almost halved inductor current ripple. In addition, this thesis also proposed two new schemes to improve the efficiency of conventional H-bridge inverter topology. The first scheme is to add an auxiliary zero-voltage-transition (ZVT) circuit to realize zero-voltage-switching (ZVS) for all the main switches and inherent zero-current-switching (ZCS) for the auxiliary switches. The advantages include the provision to implement zero state modulation schemes to decrease the inductor current THD, naturally adaptive auxiliary inductor current and elimination of need for large balancing capacitors. The second proposed scheme improves the system efficiency while still meeting a given THD requirement by implementing variable instantaneous switching frequency within a line frequency cycle. This scheme aims at minimizing the combined switching loss and inductor core loss by including different characteristics of the losses relative to the instantaneous switching frequency in the optimization process.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

POWER CONDITIONING UNIT FOR SMALL SCALE HYBRID PV-WIND GENERATION SYSTEM

Small-scale renewable energy systems are becoming increasingly popular due to soaring fuel prices and due to technological advancements which reduce the cost of manufacturing. Solar and wind energies, among other renewable energy sources, are the most available ones globally. The hybrid photovoltaic (PV) and wind power system has a higher capability to deliver continuous power with reduced energy storage requirements and therefore results in better utilization of power conversion and control equipment than either of the individual sources. Power conditioning units (p.c.u.) for such small-scale hybrid PV-wind generation systems have been proposed in this study. The system was connected to the grid, but it could also operate in standalone mode if the grid was unavailable. The system contains a local controller for every energy source and the grid inverter. Besides, it contains the supervisory controller. For the wind generator side, small-scale vertical axis wind turbines (VAWTs) are attractive due to their ability to capture wind from different directions without using a yaw. One difficulty with VAWTs is to prevent over-speeding and component over-loading at excessive wind velocities. The proposed local controller for the wind generator is based on the current and voltage measured on the dc side of the rectifier connected to the permanent magnet synchronous generator (PMSG). Maximum power point tracking (MPPT) control is provided in normal operation under the rated speed using a dc/dc boost converter. For high wind velocities, the suggested local controller controls the electric power in order to operate the turbine in the stall region. This high wind velocity control strategy attenuates the stress in the system while it smoothes the power generated. It is shown that the controller is able to stabilize the nonlinear system using an adaptive current feedback loop. Simulation and experimental results are presented. The PV generator side controller is designed to work in systems with multiple energy sources, such as those studied in this thesis. One of the most widely used methods to maximize the output PV power is the hill climbing technique. This study gives guidelines for designing both the perturbation magnitude and the time interval between consecutive perturbations for such a technique. These guidelines would improve the maximum power point tracking efficiency. According to these guidelines, a variable step MPPT algorithm with reduced power mode is designed and applied to the system. The algorithm is validated by simulation and experimental results. A single phase H-bridge inverter is proposed to supply the load and to connect the grid. Generally, a current controller injects active power with a controlled power factor and constant dc link voltage in the grid connected mode. However, in the standalone mode, it injects active power with constant ac output voltage and a power factor which depends on the load. The current controller for both modes is based on a newly developed peak current control (p.c.c.) with selective harmonic elimination. A design procedure has been proposed for the controller. Then, the method was demonstrated by simulation. The problem of the dc current injection to the grid has been investigated for such inverters. The causes of dc current injection are analyzed, and a measurement circuit is then proposed to control the inverter for dc current injection elimination. Characteristics of the proposed method are demonstrated, using simulation and experimental results. At the final stage of the study, a supervisory controller is demonstrated, which manages the different operating states of the system during starting, grid-connected and standalone modes. The operating states, designed for every mode, have been defined in such a hybrid model to allow stability and smooth transition between these states. The supervisory controller switches the system between the different modes and states according to the availability of the utility grid, renewable energy generators, the state of charge (SOC) of energy storage batteries, and the load. The p.c.u. including the supervisory controller has been verified in the different modes and states by simulation

Modelling, Design and Implementation of D-Q Control in Single-Phase Grid-Connected Inverters for Photovoltaic Systems used in Domestic Dwellings.

This thesis focuses on the single-phase voltage-source inverter for use in photovoltaic (PV) electricity generating systems in both stand-alone and grid-tied applications. In many cases, developments in single-phase PV systems have followed developments in three-phase systems. Time-variant systems are more difficult to control than time-invariant systems. Nevertheless, by using suitable transformation techniques, time-variant systems can often be modelled as time-invariant systems. After the transformation, the control signals that are usually time-variant (often varying sinusoidally in time) become time-invariant at the fundamental frequency, and are hence much easier to deal with. With this approach, synchronous rotating frame control techniques have been previously proposed for high performance three-phase inverter applications. The transformation theory cannot be applied directly in single-phase systems without modification, and the d-q components would not be time-invariant in situations where harmonics, resonances or unbalance is present. Single-phase inverter controller designs based on the use of a synchronous rotating reference frame have been proposed, but such designs do not always perform as well as expected. This thesis aims to improve single-phase voltage-source inverters. The main objective is to address, in terms of cost, efficiency, power management and power quality, the problems found with single-phase designs based on a synchronous rotating frame single-phase inverter controller. Consequently, this thesis focuses on a novel controller approach in order to obtain a more reliable and flexible single-phase inverter. As the first step, this thesis investigates the single-phase inverter switching gate-drive algorithms and develops a form of space-vector pulse-width-modulation (SVPWM) in order to reduce total harmonic distortion. The results of the new SVPWM algorithm demonstrate its superior performance when compared with sinusoidal pulse-width-modulation (SPWM) which is often used with single-phase inverters. The second step, which is further reviewed and presented in this thesis, is the modelling of the single-phase inverter control based on the synchronous rotating frame. A mathematical analysis is conducted to determine the mechanism of the coupling that exists between the voltage phase and amplitude terms, and a new transformation strategy is proposed based on using the voltage phase as a reference at the Park transformation stages, and the current phase as a reference for the current at the transformation stages. The line-frequency components of the feedback signals are transformed to time-invariant components, thus eliminating the ripple and reducing the computational burden associated with the controller stage. Consequently, the inverter feedback controller stage is designed so that the coupling terms are decoupled within the controller itself. The effectiveness of the techniques proposed in this thesis are demonstrated by simulation using the MATLAB/SIMULINK environment. The proposed technique was also investigated through a practical implementation of the control system using a Digital Signal Processor (DSP) and a single-phase inverter. This practical system was tested up to 1 kW only (limited by the available inverter hardware). Nevertheless, the correlation between the simulation and the practical results is high and this gives confidence that the developed mechanism will allow the 2.5kW goal to be achieved. Practical test cases illustrate the effectiveness of the models. In addition, the comparisons between experimental and simulation results permit the system’s behaviour and performance to be accurately evaluated. With the development of the new controller, small-scale single-phase renewable energy systems will become more useful in the field of power quality management through their ability to separately control the phase and amplitude of the output voltage. Consequently, incorporation of this type of generator within the national electrical distribution network, as distributed generators (DG) at low-voltage level, can assist with power quality management at the consumer side of the grid. In addition, such a generator can also operate in stand-alone mode if the grid becomes unavailable. The third step in this thesis investigates small-scale single-phase renewable energy systems operating as decentralized distributed generators within a local network. This operation is achieved by controlling the inverter side using the quantities measured at the common coupling point between the grid and the inverter, without requiring other extensive communications. Thus, the small-scale single-phase renewable energy distributed generator systems will contain only a local controller at each installation.Republic of Iraqi Ministry of Higher Education and Scientific researc