Co-design of Reconfigurable and Multifunction Passive RF/Microwave Components

In order to meet the market demands, multi-band communication systems that are able to accommodate different wireless technologies to be compatible with different wireless standards should be investigated and realized. Multifunction and multi-band RF front-end components are promising solutions for reducing the size and enhancing the performance of multi-band communication systems. This dissertation focuses on the design and implementation of different multifunction and tunable microwave components for use in multi-standard, flexible transceiver. For frequency-domain duplexing (FDD) communication systems, in which the uplink and downlink channels are carried on different RF frequencies, a diplexer is an essential component to separate the transmitting and receiving signals from the antenna. Electrically tunable diplexers simplify the architecture of reconfigurable RF-front end. Moreover, in modern communication systems, the crowding of the spectrum and the scaling of electronics can result in higher common-mode interference and even-order non-linearity issues. In this dissertation, three tunable compact SIW-based dual-mode diplexers, with various SE (single-ended) and BAL (balanced) capabilities, are introduced for the first time. The dual-mode operation results in a dependent tuning between the two ports. The presented designs are for SE-SE, SE-BAL, and BAL-BAL. However, based on the presented design concepts, any combination of the diplexer ports can be achieved in terms of supporting the balanced and single-ended system interface. The fabricated diplexers show low insertion loss, high isolation, good tuning range and high common mode rejection. Tunable bandstop filter (BSF) is one of the essential components in the design of RF front-ends that require wide-band operations. A wide-open front-end leaves the receiver vulnerable to jamming by high-power signals. As a result, this type of front-ends requires dynamic isolation of any interfering signal. Realization of such filters in a balanced configuration, as a second function, is an important step in the realization of full-balanced RF front-ends. Balanced (differential) circuits have many important advantages over unbalanced (single-ended) circuits such as immunity to system noise, reduction of transient noise generation and inherent suppression of even-order nonlinearities. All reported balanced filters are bandpass filters that target wide pass-bands and high common-mode rejection. These filters are necessary for wide-band RF front-ends but, as mentioned above, leave the system open to interferers and jammers. In this dissertation, a new differential coupling structure for evanescent-mode cavity resonators is developed, enabling the design of fully-balanced tunable BSF. The proposed filter is tunable from 1.57-3.18 GHz with 102% tuning range. In addition, over the full range, the measured 10-dB fractional bandwidth ranges from 1-2.4%, and the attenuation level is better than 47 dB. Lastly, Substrate Integrated Waveguide (SIW) evanescent-mode cavity resonators (EVA) are employed in the design of RF couplers, quadrature hybrid and rat-race couplers. These couplers are used in the design of numerous RF front-end components such as power amplifiers, balanced mixers, and antenna array feeding networks. Utilizing such resonators (EVA) in the design allows the couplers to have wide spurious-free range, low power consumption, high power handling capability and both tunability and filtering capabilities. The proposed quadrature hybrid coupler can be tuned starting from 1.32–2.22 GHz with a measured insertion loss range from 1.29 to 0.7 dB. The measured reflection and isolation are better than 12 dB and 17 dB, respectively. Moreover, the coupler has a measured spurious free range of 5.1–3fo (lowest–highest frequency). Regarding rat-race coupler, two designs are introduced. The first design is based on a full-mode cavity while the second one is more compact and based on a half-mode cavity. Both designs show more than 70% tuning range, and the isolation is better than 30 dB

Antennas and Arrays for Mobile Platforms -- Direct Broadcast Satellite and Wireless Communication

Flexibility of any proposed communication links is becoming one of the most challenging features. Direct broadcasting satellite services, for example, will be greatly enhanced by providing service-on-the-move. This market is very demanding as it necessitates the development of a low cost, low profile antenna that can be mounted on top of SUVs and minivans, which is capable of continuously tracking the satellite. Another example is the wireless antennas for laptops and smart-phones, where the antennas should fit within an extremely small volume and should be capable of addressing many services over wide frequency range. In this dissertation, both DBS and the wireless antennas are addressed. In these studies, efforts have been concentrated in developing low profile planar antennas, in particular, slot arrays. Travelling wave slotted waveguide arrays have been utilized to minimize the scanning angle range limits due to their inherent beam tilt angle. CNC machines were utilized first to fabricate the early prototypes for sub-array developments. Subsequently, a low cost fabrication technology is adopted to develop a low cost and light weight full array using substrate integrated waveguides (SIWs). The SIW is fully characterized and an excellent equivalent model has been derived to allow easy translation of metallic waveguide components to SIW. Various SIW junctions, transitions, and arrays have been developed for array feed networks including a 64 radiating SIW full array and a 32 radiating SIW array with folded feed. Meanwhile, for the wireless antennas, the utilization of reconfigurable hardware has been introduced to provide the required multi-functionality services and wide frequency coverage. Various reconfigurable antennas were developed and utilized to demonstrate their advantages compared to other design options such as wide-band or multi-band approaches. Both micro-electro-mechanical switches MEMS and PIN diodes have been successfully utilized to switch between the different configurations. The placement, control, and modeling of the switches are also discussed and novel modeling and biasing topologies are introduced. A novel and practical concept of reconfigurable multiband antenna is introduced here too, where advantages of both the multi-band and the reconfigurable antenna structures can be simultaneously achieved while supporting more services

Size Reduction and Harmonics Suppression in Microwave Power Dividers: A Comprehensive Review

In this paper, several types of microstrip power divider are studied and compared in terms of harmonics suppression and size reductions. The importance of this research lies in the fact that power dividers are critical components in various communication systems, and their performance directly affects the overall system efficiency. The conventional structure of the power divider has an acceptable performance at operating frequency in terms of excellent output ports isolation, low insertion loss, and high return loss, but occupies large size and passes unwanted signals at higher frequencies along with desired signal without any suppression. Harmonics are popular distortion and has different distortion impacts in many different facilities. Recently, several techniques are introduced to overcome these drawbacks. Applied open stubs, applied resonators, lumped reactive components such as capacitors and inductors, coupled lines, defected ground structure (DGS), and electronic band gaps are common methods, which are widely used to overcome these drawbacks. Finally, the study results show that the resonator-based power dividers and coupled-line-based power dividers have good performances in terms of size reduction and harmonic suppression but increase insertion loss parameter. Furthermore, the lumped reactive component-based power dividers and applied DGS and electromagnetic bandgap cells suppress unwanted harmonics, but they need extra process to fabrication, which is undesirable. Moreover, the open-stub-based power dividers have moderate performance with simple structure, but size reduction and harmonics suppression are not so superior in this method

Design of Ku-band power divider using Substrate Integrated Waveguide technique

A Ku-band Substrate Integrated Waveguide power divider is proposed. In this work, the SIW power divider is designed with T-junction configuration. The SIW technique enables the power divider to have low insertion loss, low cost and features uniplanar circuit. An additional of metallic via hole is added in the center of the junction to improve the return loss performance of the T-junction SIW power divider. The simulated input return losses at port 1 are better than 27 dB, and features equal power division of about -3.1 dB ±0.4 dB at both output ports across frequency range of 13.5-18 GHz. The SIW power divider is fabricated, and the measurement results show acceptable performances. Since there are some losses contributed by the SMA connector of the fabricated SIW power divider prototype, an additional SIW transmission line is simulated and fabricated to analyze the connector loss

Multilayered balanced dual-band bandpass filter based on magnetically coupled open-loop resonators with intrinsic common-mode rejection

A new dual-band balanced bandpass filter based on magnetically coupled open-loop resonators in multilayer technology is proposed in this paper. The lower differential passband, centered at the Global Positioning System (GPS) L1 frequency, 1.575 GHz, was created by means of two coupled resonators etched in the middle layer of the structure, while the upper differential passband, centered at a Wi-Fi frequency of 2.4 GHz, was generated by coupling two resonators on the top layer. Magnetic coupling was used to design both passbands, leading to an intrinsic common-mode rejection of 39 dB within the lower passband and 33 dB within the upper passband. Simulation and measurement results are provided to verify the usefulness of the proposed dual-band differential bandpass filter.Ministerio de Ciencia, Innovación y Universidades TEC2017-84724-

Millimeter-Wave Components and Antennas for Spatial and Polarization Diversity using PRGW Technology

The evolution of the wireless communication systems to the future generation is accompanied by a huge improvement in the system performance through providing a high data rate with low latency. These systems require access to millimeter wave (mmWave) bands, which offer several advantages such as physically smaller components and much wider bandwidthcomparedtomicrowavefrequencies. However, mmWavecomponentsstillneed a significant improvement to follow the rapid variations in future technologies. Although mmWave frequencies can carry more data, they are limited in terms of their penetration capabilities and their coverage range. Moreover, these frequencies avoid deploying traditional guiding technologies such as microstrip lines due to high radiation and material losses. Hence, utilizing new guiding structure techniques such as Printed Ridge Gap Waveguide (PRGW) is essential in future mmWave systems implementation. ThemainpurposeofthisthesisistodesignmmWavecomponents,antennasubsystems and utilize both in beam switching systems. The major mmWave components addressed in this thesis are hybrid coupler, crossover, and differential power divider where the host guidingstructureisthePRGW.Inaddition,variousdesignsfordifferentialfeedingPRGW antennas and antenna arrays are presented featuring wide bandwidth and high gain in mmWave band. Moreover, the integration of both the proposed components and the featured antennas is introduced. This can be considered as a significant step toward the requirements fulfillment of today's advanced communication systems enabling both space and polarization diversity. The proposed components are designed to meet the future ever-increasing consumer experience and technical requirements such as low loss, compact size, and low-cost fabrication. This directed the presented research to have a contribution into three major parts. The first part highlights the feeding structures, where mmWave PRGW directional couplers and differential feeding power divider are designed and validated. These components are among the most important passive elements of microwave circuits used in antennabeam-switchingnetworks. Different3-dBquadraturehybridcouplersandcrossover prototypes are proposed, featured with a compact size and a wide bandwidth beyond 10 % at 30 GHz. In the second part, a beam switching network implemented using hybrid couplers is presented. The proposed beam switching network is a 4 × 4 PRGW Butler matrix that used to feed a Magneto-electric (ME) dipole antenna array. As a result, a 2-D scanning antenna array with a compact size, wide bandwidth, and high radiation efficiency larger than84%isachieved. Furthergainenhancementof5dBiisachievedthroughdeployinga hybridgainenhancementtechniqueincludingAMCmushroomshapesaroundtheantenna array with a dielectric superstrate located in the broadside direction. The proposed scanning antenna array can be considered as a step toward the desired improvement in the data rate and coverage through enabling the space diversity for the communication link. The final activity is related to the development of high-gain wide-band mmWave antenna arrays for potential use in future mmWave applications. The first proposed configuration is a differential feeding circular polarized aperture antenna array implemented with PRGW technology. Differential feeding antenna designs offer more advantages than single- ended antennas for mmWave communications as they are easy to be integrated with differential mmWave monolithic ICs that have high common-mode rejection ratio providing an immunity of the environmental noise. The proposed differential feeding antenna array is designed and fabricated, which featured with a stable high gain and a high radiation efficiency over a wide bandwidth. Another proposed configuration is a dualpolarized ME-dipole PRGW antenna array for mmWave wireless communication. Dual polarizationisconsideredoneofthemostimportantantennasolutionsthatcansavecosts and space for modern communication systems. In addition, it is an effective strategy for multiple-input and multiple-output systems that can reduce the size of multiple antennas systems by utilizing extra orthogonal polarization. The proposed dual- polarized antenna array is designed to achieve a stable gain of 15 ± 1 dBi with low cross- polarization less than -30 dB over a wide frequency range of 20 % at 30 GHz

Microwave and Millimeter-wave Miniaturization Techniques, and Their Applications

Miniaturization is an inevitable requirement for modern microwave and mm-wave circuits and systems. With the emerging of high frequency monolithic integrated circuits, it is the passive components’ section that usually occupies the most of the area. As a result, developing creative miniaturization techniques in order to reduce the physical sizes of passive components while keep their high performance characteristics is demanding. On the other hand, it is the application that defines the importance and effectiveness of the miniaturization method. For example, in commercial handset wireless communication systems, it is the portability that primarily dictates miniaturization. However, in case of liquid sensing applications, the required volume of the sample, cost, or other parameters might impose size limitations. In this thesis, various microwave and mm-wave miniaturization methods are introduced. The methods are applied to various passive components and blocks in different applications to better study their effectiveness. Both componentlevel designs and system-level hybrid integration are benefited from the miniaturization methods introduced in this thesis. The proposed methods are also experimentally tested, and the results show promising potential for the proposed methods