High efficiency smart voltage regulating module for green mobile computing

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In this thesis a design for a smart high efficiency voltage regulating module capable of supplying the core of modern microprocessors incorporating dynamic voltage and frequency scaling (DVS) capability is accomplished using a RISC based microcontroller to facilitate all the functions required to control, protect, and supply the core with the required variable operating voltage as set by the DVS management system. Normally voltage regulating modules provide maximum power efficiency at designed peak load, and the efficiency falls off as the load moves towards lesser values. A mathematical model has been derived for the main converter and small signal analysis has been performed in order to determine system operation stability and select a control scheme that would improve converter operation response to transients and not requiring intense computational power to realize. A Simulation model was built using Matlab/Simulink and after experimenting with tuned PID controller and fuzzy logic controllers, a simple fuzzy logic control scheme was selected to control the pulse width modulated converter and several methods were devised to reduce the requirements for computational power making the whole system operation realizable using a low power RISC based microcontroller. The same microcontroller provides circuit adaptations operation in addition to providing protection to load in terms of over voltage and over current protection. A novel circuit technique and operation control scheme enables the designed module to selectively change some of the circuit elements in the main pulse width modulated buck converter so as to improve efficiency over a wider range of loads. In case of very light loads as the case when the device goes into standby, sleep or hibernation mode, a secondary converter starts operating and the main converter stops. The secondary converter adapts a different operation scheme using switched capacitor technique which provides high efficiency at low load currents. A fuzzy logic control scheme was chosen for the main converter for its lighter computational power requirement promoting implementation using ultra low power embedded controllers. Passive and active components were carefully selected to augment operational efficiency. These aspects enabled the designed voltage regulating module to operate with efficiency improvement in off peak load region in the range of 3% to 5%. At low loads as the case when the computer system goes to standby or sleep mode, the efficiency improvent is better than 13% which will have noticeable contribution in extending battery run time thus contributing to lowering the carbon footprint of human consumption

Using Building Blocks to Design Analog Neuro-Fuzzy Controllers

We present a parallel architecture for fuzzy controllers and a methodology for their realization as analog CMOS chips for low- and medium-precision applications. These chips can be made to learn through the adaptation of electrically controllable parameters guided by a dedicated hardware-compatible learning algorithm. Our designs emphasize simplicity at the circuit level—a prerequisite for increasing processor complexity and operation speed. Examples include a three-input, four-rule controller chip in 1.5-μm CMOS, single-poly, double-metal technology

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

An Investigation into Neuromorphic ICs using Memristor-CMOS Hybrid Circuits

The memristance of a memristor depends on the amount of charge flowing through it and when current stops flowing through it, it remembers the state. Thus, memristors are extremely suited for implementation of memory units. Memristors find great application in neuromorphic circuits as it is possible to couple memory and processing, compared to traditional Von-Neumann digital architectures where memory and processing are separate. Neural networks have a layered structure where information passes from one layer to another and each of these layers have the possibility of a high degree of parallelism. CMOS-Memristor based neural network accelerators provide a method of speeding up neural networks by making use of this parallelism and analog computation. In this project we have conducted an initial investigation into the current state of the art implementation of memristor based programming circuits. Various memristor programming circuits and basic neuromorphic circuits have been simulated. The next phase of our project revolved around designing basic building blocks which can be used to design neural networks. A memristor bridge based synaptic weighting block, a operational transconductor based summing block were initially designed. We then designed activation function blocks which are used to introduce controlled non-linearity. Blocks for a basic rectified linear unit and a novel implementation for tan-hyperbolic function have been proposed. An artificial neural network has been designed using these blocks to validate and test their performance. We have also used these fundamental blocks to design basic layers of Convolutional Neural Networks. Convolutional Neural Networks are heavily used in image processing applications. The core convolutional block has been designed and it has been used as an image processing kernel to test its performance.Comment: Bachelor's thesi

Analysis and Characterization of Single-Poly Floating Gate Devices in 0.35um PDSOI Process

The purpose of this thesis is to demonstrate a single-poly Floating Gate Device (FGD) in 0.35 m Partially Depleted Silicon On Insulator (PDSOI) process for use in analog circuits for post process trimming. Floating gate devices with different aspect ratios have been fabricated to facilitate this behavioral study in PDSOI process. Fundamentals of floating gate devices, the advantages and disadvantages of PDSOI compared to bulk CMOS with respect to single-poly floating gate devices are discussed. Various experiments on behavior and performance of threshold voltage have been conducted and its variation with programming/erasing time and amplitude has been analyzed. The single-poly FGD’s on-resistance variation and hysteresis behavior with threshold voltage has been documented. A mathematical relation between FGD’s on-resistance and threshold voltage has been experimentally derived. Intrinsic data retention has been estimated through extrapolation of experimental data. A process independent MATLAB simulation model has been successfully developed for understanding the threshold voltage time dependence characteristics. And finally, this work has shown that programmable or post-process trimmable analog circuits can be implemented in SOI using single-poly FGDs as programmable resistive elements. A SOI programmable beta-multiplier current reference has been successfully demonstrated using the singlepoly FGD as a resistive element

Research in the effective implementation of guidance computers with large scale arrays Interim report

Functional logic character implementation in breadboard design of NASA modular compute

34th Midwest Symposium on Circuits and Systems-Final Program

Organized by the Naval Postgraduate School Monterey California. Cosponsored by the IEEE Circuits and Systems Society. Symposium Organizing Committee: General Chairman-Sherif Michael, Technical Program-Roberto Cristi, Publications-Michael Soderstrand, Special Sessions- Charles W. Therrien, Publicity: Jeffrey Burl, Finance: Ralph Hippenstiel, and Local Arrangements: Barbara Cristi